Crestron FT-600 Operations & Installation Manual

Crestron FT-600
FlipTop™ Basic
Operations & Installation Guide

Regulatory Compliance

This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

As of the date of manufacture, the FT-600 has been tested and found to comply with specifications for CE
marking and standards per EMC and Radiocommunications Compliance Labelling.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron, the Crestron logo, DigitalMedia, and FlipTop are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for

errors in typography or photography.

This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.

Crestron FT-600 FlipTop Basic

Contents

FlipTop Basic: FT-600 1

Introduction ............................................................................................................................... 1

Features and Functions ................................................................................................ 1

Specifications .............................................................................................................. 3

Physical Description .................................................................................................... 4

Setup .......................................................................................................................................... 8

Supplied Hardware ...................................................................................................... 8

Installation ................................................................................................................... 8

Resources ................................................................................................................................. 12

Further Inquiries ........................................................................................................ 12

Future Updates .......................................................................................................... 12

Return and Warranty Policies .................................................................................................. 13

Merchandise Returns / Repair Service ...................................................................... 13

Crestron Limited Warranty ........................................................................................ 13

Operations & Installation Guide – DOC. 7596A Contents • i

Crestron FT-600 FlipTop Basic

• Flush mount tabletop connectivity in a stylish FlipTop design

FlipTop Basic: FT-600

Introduction

The FT-600 FlipTop™ Basic by Crestron® provides a highly configurable
connectivity solution in a stylish, flush mount tabletop design. Flipping open the
“FlipTop” lid accesses its connection compartment where interface cables and
connectors are kept at the ready for plugging in laptop computers, mobile devices,
AV source, and other equipment. A FlipTop is an ideal complement to a
DigitalMedia™ transmitter or any other AV interface device, providing easy access
to necessary connections while keeping the more intimidating and mundane
technology hidden away beneath the tabletop.

Features and Functions

• An ideal complement to Crestron DigitalMedia

• Configurable connection compartment allows versatile combinations of

FlipTop Design

Handsomely finished in a choice of black anodized or brushed aluminum, Crestron
FlipTops lend a contemporary metallic accent to conference tables and podiums. The
FT-600 installs cleanly in virtually any flat, horizontal surface up to 1 3/4” (44 mm)
thick. Beveled edges provide for a nearly flush appearance.

The FlipTop lid flips open with just the tip of a finger to access the connection
compartment. Once connections are made, the lid can be closed. A generous, tapered
notch at the front of the lid opening allows interface cables to remain connected even
when the lid is closed.

pull-out cables, cable retractors, connector plates, and AC power
outlets

• Tapered cable notch allows lid to be closed with cables plugged in

• Universal cutout size fits all new and future FlipTops

• Black anodized or brushed aluminum finish

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 1

FlipTop Basic Crestron FT-600

Connection Compartment

The FT-600 is highly configurable to provide a well organized connectivity solution
tailored to each unique application. It provides options for both pullout and panel­mounted connectors, with or without AC power outlets. It comes standard with two
cable pass-through plates and four blank plates, all of which can be swapped out for
a choice of cable retractors, connector plates, and AC power outlet modules.

• Cable Pass-Through Plates – Each cable pass-through plate provides four

grommeted holes to accommodate Crestron Certified Interface Cables* and
other AV, data, and communication cables. The user end of each cable
stows neatly within the connection compartment ready for use while excess
cable simply drops out of sight below the cable pass-through plate. The
grommets provide a smooth, slippery surface for easy pullout of each cable.
Blank caps are also provided to cover any unused holes. The cable
pass-through plates are positioned at the left and right sides of the
connection compartment. The FT-600 supports one or two cable
pass-through plates. Two are included.

• Cable Retractors – For an even more refined cable management solution,

the FT-600 accommodates up to six Crestron CBLR Cable Retractors*.
Crestron cable retractors feature a patent pending, lever actuated retraction
mechanism that ensures smooth operation while eliminating hanging cable
loops beneath the table. Up to three cable retractors can be installed in place
of each cable pass-through plate, allowing for a total of six cable retractors.

• Connector Plates – If panel mounted connectors are preferred, the FT-600

can accommodate up to four FTA-CP Connector Plates*. Connector plates
are offered with a variety of common AV and data connector types. Custom
connector plates may also be fabricated by the installer using the blank
plates provided. All four connector plates are positioned at the center of the
connection compartment.

• AC Power Outlet Modules – To provide power for laptops and other

portable devices, the FT-600 can be equipped with up to four AC power
outlets. A single FTA-PWR-102 Dual AC Power Outlet Module* can be
installed in place of the center two connector plates or two FTA-PWR-102s
can be installed in place of all four connector plates.

* Item(s) sold separately.

2 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

Specifications

Specifications for the FT-600 are listed in the following table.

FT-600 Specifications

SPECIFICATION DETAILS

Power Requirements

Utility power 10 amps at 125 Vac 50/60 Hz per each installed

Dual AC Power Outlet Module (FTA-PWR-102,
sold separately)

Environmental

Temperature 32º to 112º F (0º to 45º C)

Humidity 10% to 90% RH (non-condensing)

Enclosure

Chassis Metal, black

Cover Aluminum, black anodized or brushed aluminum

finish

Mounting Flush tabletop mount, 1 3/4 in (44 mm)

maximum surface thickness, 6 1/4” (159 mm)
deep x 7 1/2 in (190 mm) wide cutout (template
provided)

Dimensions

Height 7.06 in (180 mm)

10.80 in (275 mm) with lid open

Width 7.98 in (203 mm)

9.19 in (234 mm) with mounting brackets

Depth 6.77 in (172 mm)

7.88 in (200 mm) with lid open

Weight 5.6 lb (2.5 kg)

Available Models

FT-600-B FlipTop Basic, Black Anodized

FT-600-BALUM Flip Top Basic, Brushed Aluminum

Available Accessories

CBL Series Crestron Certified Interface Cables

CBLR Series Cable Retractors

CBLRA-BRKT-3-H Horizontal Mounting Option for CBLR

CBLRA-INSERT-2WIRE 2-Wire Insert for Cable Retractor Option

FTA-CP-DP-101 FlipTop Connector Plate, DisplayPort

FTA-CP-HD-101 FlipTop Connector Plate, HDMI

FTA-CP-RCA-103 FlipTop Connector Plate, RCA x 3

FTA-CP-RJ45-102 FlipTop 2 Connector Plate, RJ45 x 2

FTA-CP-USB-102 FlipTop Connector Plate, USB x 2

FTA-PWR-102 FlipTop Dual AC Power Outlet Module, NEMA 5

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 3

FlipTop Basic Crestron FT-600

6.22 in

(158 mm)

7.98 in

(203 mm)

6.77 in

(172 mm)

Physical Description

This section provides information on the connections, controls, and indicators
available on the FT-600.

FT-600 Overall Dimensions (Top View)

4 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

7.28 in

(185 mm)

6.72 in

(171 mm)

FT-600 Overall Dimensions (Front View)

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 5

FlipTop Basic Crestron FT-600

7.06 in

(180 mm)

6.94 in

(177 mm)

3.75 in

(95 mm)

5.12 in

(130 mm)

6.07 in

(155 mm)

7.88 in

(200 mm)

FT-600 Overall Dimensions (Side View)

6 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

Ground

FT-600 (Oblique View)

FT-600 (Bottom View)

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 7

FlipTop Basic Crestron FT-600

Setup

Supplied Hardware

The hardware supplied with the FT-600 is listed in the following table.

Supplied Hardware for the FT-600

DESCRIPTION PART NUMBER QUANTITY

Metal, Plate, Mounting 2036985 2

Screw, 10-32 x 2”, Steel, Socket HD, Zinc 2037109 4

Small Hole Plug 2036647 4

Large Hole Plug 2036649 4

Small Bushing, 5/16” ID, 0.5” OD 2009522 4

Large Bushing, 0.55” ID, 0.80” OD 2010496 4

Installation

NOTE: To prevent overheating, do not operate this product in an area that exceeds
the environmental temperature range listed in the table of specifications.
Consideration must be given if installed in a closed assembly, inside a closed desk or
in a closed podium since the operating ambient temperature of these environments
may be greater than the room ambient temperature. Contact with thermal insulating
materials should be avoided on all sides of the unit.

Cable Management Plates

The FT-600 ships with two cable management plates pre-installed. These provide a
pullout cable solution for the cables. Cables are looped through the cable
management plates.

The included bushings must be installed before mounting the FT-600 in a surface.
For a neat appearance, any unused openings can be filled using the included hole
plugs. The only tool required is a Phillips screwdriver.

1. Remove the two cable management plates and retain the 06-32 x 1/4” screw

that holds each one in place.

2. Place the bushings on the cables (eight bushings supplied).

3. Thread the cables through the appropriate slots on each plate.

4. Snap the bushings into the plate slots.

5. Feed all excess cable through the opening.

6. Attach each plate by first sliding its dovetail into the slot toward the rear of

the inside of the FT-600, then dropping the front into place and securing it
with the 06-32 x 1/4” screw from step 1. Refer to the following illustration.

8 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

Cable Management Plates (2)

Bushing

06-32 x 1/4” Screws (2)

Mounting Plate Dovetail Inserts Here

Maximum

Radius

1/8 in

(4 mm)

6 1/4 in

(159 mm)

7 1/2 in

(190 mm)

Cable Management Plate Installation

Mounting in a Surface

The FT-600 is designed to mount in a horizontal surface, such as a desktop, lectern,
or podium. The following diagram illustrates the required opening size to
accommodate the FT-600. A cutout template (40143) is included.

Cutout Dimensions

NOTE: Before inserting the FT-600 in the mounting hole, ensure that all required
cables have been installed.

Tools required:

• Phillips screwdriver

• #10 Allen wrench

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 9

FlipTop Basic Crestron FT-600

Surface Cutout

Studs for Mounting Plate

Use the following procedure to mount the FT-600.

1. Position the FT-600 in the mounting hole.

Mounting Plate Stud Locations

2. Install the four #10-32 socket screws (2037109) in the metal mounting

plates (2036985) (two screws per plate). Refer to the following illustration.

10 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

Screws (4) #10-32 x 2”,
Steel, Socket HD

Mounting Plates (2)

Mounting Surface

Mounting Plate Installation

3. Slide the mounting plates over the studs on each side of the FT-600.

4. Turn the four #10-32 socket screws equally, until they contact the underside

of the mounting surface.

NOTE: Do not overtighten the #10 screws as this may damage the surface
or the unit.

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 11

FlipTop Basic Crestron FT-600

Resources

Further Inquiries

To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for
assistance within a particular geographic region, refer to the listing of Crestron
worldwide offices at

To post a question about Crestron products, log onto Crestron’s Online Help at

www.crestron.com/onlinehelp. First-time users must establish a user account to fully

benefit from all available features.

Future Updates

As Crestron improves functions, adds new features, and extends the capabilities of
the FT-600, additional information may be made available as manual updates. These
updates are solely electronic and serve as intermediary supplements prior to the
release of a complete technical documentation revision.

www.crestron.com/offices.

Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.

12 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange or service without prior authorization from

Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer.
Only authorized Crestron dealers may contact the factory and request an RMA (Return
Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number and return address.

2. Products may be returned for credit, exchange or service with a Crestron Return Merchandise

Authorization (RMA) number. Authorized returns must be shipped freight prepaid to Crestron,
6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number clearly marked
on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall
be subject to refusal. Crestron reserves the right in its sole and absolute discretion to charge a 15%
restocking fee plus shipping costs on any products returned with an RMA.

3. Return freight charges following repair of items under warranty shall be paid by Crestron,

shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.

Crestron Limited Warranty

Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and
workmanship under normal use for a period of three (3) years from the date of purchase from Crestron,
with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads
and power supplies are covered for a period of one (1) year; touch screen display and overlay components
are covered for 90 days; batteries and incandescent lamps are not covered.

This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.

Crestron shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.

This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron
be liable for incidental or consequential damages of any kind (property or economic damages inclusive)
arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or
made by the purchaser for a third party.

Crestron shall, at its option, repair or replace any product found defective, without charge for parts or labor.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.

Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied,
nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or
fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms
of this limited warranty. This warranty statement supersedes all previous warranties.

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 13

FlipTop Basic Crestron FT-600

This page is intentionally left blank.

14 • FlipTop Basic: FT-600 Operations & Installation Guide – DOC. 7596A

Crestron FT-600 FlipTop Basic

This page is intentionally left blank.

Operations & Installation Guide – DOC. 7596A FlipTop Basic: FT-600 • 15

Crestron Electronics, Inc. Operations & Installation Guide – DOC. 7596A

15 Volvo Drive Rockleigh, NJ 07647 (2038123)
Tel: 888.CRESTRON 10.13
Fax: [phone] Specifications subject to
www.crestron.com change without notice.