Crestron FT2A-UTK-CLOAK-1T, FT2A-UTK-CLOAK, FT2A-UTK-CLOAK-WIDE, FT2A-UTK-CLOAK-WIDE-1T User Manual
Hook-and-loop
Hook-and-loop
fastener strips (4)
bracket
Power supply
Hook-and-loop fastener strips
FT2A-UTK-CLOAK Series
Under-Table Cloak for FT2 Series FlipTop™ Cable Management Solutions
The Crestron® FT2A‑UTK‑CLOAK, FT2A‑UTK‑CLOAK‑1T, FT2A‑UTK‑CLOAK‑WIDE, and FT2A‑UTK‑CLOAK‑WIDE‑1T are used to conceal
exposed cables and retractors in under‑table FT2 Series FlipTop™ applications.
The FT2A‑UTK‑CLOAK, FT2A‑UTK‑CLOAK‑WIDE, FT 2A‑UTK‑CLOAK‑1T, and FT2A‑UTK‑CLOAK‑WIDE‑1T are functionally similar. For simplicity
within this guide, the term “cloak ” is used except where noted.
The following information provides compatible FlipTop models and cable retractor types for each cloak.
Cloak Model Compatible FT2 Series Model
FT2A‑UTK‑CLOAK
Conceals up to four gravity retractors.
FT2A‑UTK‑CLOAK‑1T
Conceals up to four one‑touch retractors.
FT2A‑UTK‑CLOAK‑WIDE
Conceals up to four gravity retractors.
FT2A‑UTK‑CLOAK‑WIDE‑1T
Conceals up to four one‑touch retractors.
FT2A-UTK-CLOAK FT2A-UTK-CLOAK-WIDE-1T
fastener strips (4)
FT2‑202‑MECH, FT2‑202‑MECH‑AC, FT2‑202‑MECH‑ACUSB, FT2‑500‑MECH,
FT2‑500‑MECH‑AC, FT2‑500‑MECH‑ACUSB, FT2‑700‑MECH, FT2‑700‑MECH‑AC, FT2‑700‑
MECH‑ACUSB, FT2‑1200‑MECH, FT2‑1200‑MECH‑AC, FT2‑1200‑MECH‑ACUSB
FT2‑202‑ELEC, FT2‑500‑ELEC, FT2‑700‑ELEC, FT2‑1200‑ELEC
FT2‑1400‑MECH, FT2‑1400‑MECH‑AC, FT2‑1400‑MECH‑ACUSB
FT2‑1400‑ELEC
fastener strips (4)
>
Attach the Cloak
Attach the cloak to the FlipTop assembly after the assembly has been installed in the table and the cable retractors and modules are installed
in the assembly.
NOTE: Do not fold the cloak. Once creases are made in the fabric, they cannot be removed.
1. Locate the four small strips of hook‑and‑loop fasteners and remove them from the cloak. These four strips shall be applied to the portion
of the FlipTop enclosure that sits beneath the table.
2. Determine the placement of each fastener strip on the FlipTop enclosure. The top of the power supply bracket may be used as a guideline
around the enclosure for fastener placement.
NOTE: A minimum of two strips of hook‑and‑loop fasteners must be used. If only two strips are needed for the installation, place a strip
on the front power supply bracket and on the rear of the of the enclosure. These strips are outlined in blue in the illustration.
Recommended hook-and-loop fastener placement
fastener strip
bracket
*Inside
>
Check the Box
Item Qty
FT2A-UTK-CLOAK, FT2A-UTK-CLOAK-1T, FT2A-UTK-CLOAK-WIDE, or FT2A-UTK-CLOAK-WIDE-1T 1
*Inside
Power supply
3. Remove the protective backing from the fastener strips, and press them firmly onto the FlipTop enclosure.
4. Align the inside of the cloak with the hook‑and‑loop fasteners to the fastener strips applied to the FlipTop enclosure.
5. Carefully wrap and press the cloak onto the fastener strips attached to the FlipTop enclosure.
Hook-and-loop
FlipTop enclosure
Power supply bracket
Cloak
6. To prevent tangling or cable movement obstruction, ensure that the cables are routed properly within the cloak.
Additional Information
Scan or click the QR code for detailed product information.
FT 2 A‑UTK‑CLOAK FT 2 A‑UTK‑CLOAK‑1T FT 2 A‑UTK‑CLOAK‑WI DE FT 2 A‑UTK‑CLOAK‑WI DE‑1T
Compliance and Legal
Original Instructions: The U. S. Engl ish version of this document is t he original in stru ctio ns. All other l anguages are a transla tion of t he original instructio ns.
The product wa rrant y can be fo und at www.crestron.com/warranty.
The spe cific patent s that cover Crestron p roduc ts are l isted at www.crestron.com/legal/patents.
Certa in Cres tron products contain open source s oft ware. For speci fic informat ion, please v isit www.crestron.com/opensource.
Crestron, the Crestron logo, FlipTop, and FlipTops are ei ther trademarks or registered tradema rks of Crestro n Elec tronics, Inc. in the United States an d/or other countries. O ther
tradem arks , regis tered t radem arks , and tra de name s may be used in th is docu ment to re fer to either th e entit ies claiming the mark s and nam es or their product s. Cres tron disclaims any
propri etar y intere st in the marks a nd name s of othe rs. Cre stron is not res ponsible for e rrors i n typography or photo graphy.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Dr ive, Rockleig h, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 8532A
Specifications subject to
change without notice.
(2054 497)
10/10/19
Loading...