Page 1
Power outlet module
Locking bars (3)
FT2A-PWR-US-2-BX
The retractable
Lid retraction button
FT2A-PWR-US-2-BX
AC Power Outlet Module for FT2 Series
Suitable for use in the US and other countries, the Crestron® FT2A‑PWR‑US‑2‑BX provides two
NEMA Type 5 AC power outlets for installation in Crestron FT2 FlipTop™ cable management
assemblies.
The fixed 6 ft (1.83 m) BX pigtail connects the FT2A‑PWR‑US‑2‑BX to an electrical box. The
FT2 A‑PWR‑US‑2‑BX is rated for 10 A (total) at 125 V, 50/60 Hz.
NOTE: Only a qualified electrician should connect the module to the available electrical supply.
FT2A-PWR-US-2-BX
BX pigtail
6 ft (1.83 m)
Install the Module
Install the power module into the FT2 FlipTop assembly. If the bezel and locking bars have not
been installed on the FT2 FlipTop assembly, skip to step 5.
NOTE: The FT2A‑PWR‑US‑2‑BX uses three module slots. For ease of installation, install power
outlet modules before installing any other module.
To install the power outlet module:
1. Tap the lid retraction button to retract the one‑touch lid, which disappears into the FT2
FlipTop assembly. If the assembly has two lids, retract both.
2. Remove and retain the magnetic bezel from the FT2 FlipTop assembly by grasping the
inside of the bezel and firmly pulling it up and away from the assembly until the magnetic
hold is broken.
3. Use a manual torque screwdriver to unscrew, remove and retain the two locking bars on
either side of the module row where the module is to be installed.
Remove Two Locking Bars
Attach the Bezel
lid fits inside
this opening in
the bezel.
Retractable lid
Check the Box
Item Qty
FT2A‑PWR‑US‑2‑BX 1
4. Lift and remove the modules to be replaced.
5. Insert the new module’s BX pigtail cable through the empty module slots.
6. Orient the module as shown in the following illustration and slide it down into the
appropriate module slots. Use the guide ribs on the front and rear of the module to help
position it in the assembly.
Position the Module
7. Confirm that all modules are level with their surroundings and place the locking bars
(removed in step 3) into position so that the screws on either side engage the screw holes
in the assembly.
8. Use a manual torque screwdriver set to its lowest possible setting to tighten the locking
bar screws until the lock bars are secured to the FT2 FlipTop assembly.
9. Place the bezel (removed in step 2) onto the FT2 FlipTop assembly so that the retractable
lid fits inside the bezel opening. The bezel is held in place by magnets.
Wire the Module
Wire the FT2A‑PWR‑US‑2‑BX pigtail cable in accordance with appropriate electrical codes and
regulations.
Operate the Module
To operate the power outlet module:
1. Tap the lid retraction button to retract the one‑touch lid, which disappears into the FT2
FlipTop assembly.
2. Connect the device needing power to one of the available outlets on the module.
3. Confirm that the power indicator on the device shows that the device is receiving power.
Page 2
Additional Information
Scan or click the QR code for detailed product information.
FT2A‑PWR‑US‑2‑BX
Compliance and Legal
Original Instructions: The U. S. English version of thi s document is the o riginal instructi ons. All other l anguages are a translat ion
of the original instructions.
Regulatory Model: M201907002
Federal Communications Commission (FCC) Compliance Statement
This dev ice comp lies with part 15 of the FCC Rules. Operation is su bject to the following co nditi ons: (1) This dev ice may n ot
cause ha rmful interference and (2) this d evice must accep t any inter feren ce recei ved, inc luding i nterf erence t hat may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s a uthor ity to op erate the equip ment.
NOTE: This e quipm ent has been tested and found to comp ly with the limi ts for a Cl ass B digi tal devi ce, purs uant to part 15
of the FCC Rules. T hese limits are design ed to prov ide reasonable protection a gains t harmfu l inter ference in a residential
instal lation. This e quipment gene rates, u ses and can radiat e radio frequenc y energy and, if n ot installed an d used in
accorda nce with the ins tructions, may caus e harmful inter ferenc e to radio co mmunications . Howeve r, there is no gu arantee
that int erference wil l not occu r in a particula r instal lation. If this equipm ent does cause harmful interference to radio or
televi sion reception, which can be determined by turnin g the equipment o ff and on, the user is encouraged to try to co rrect the
inter ference by one or mo re of the fo llowin g measures:
• Reori ent or rel ocate th e receiving antenna.
• Increase the separation between the equipment and receiver.
• Conne ct the equipm ent into an o utlet o n a circuit different from t hat to which the re ceiver is connec ted.
• Consu lt the de aler or an experi enced radio/TV technician for help.
This pro duct is Liste d to appli cable UL® Standards and re quirem ents tested by Underwriters Laboratories Inc.
The product warranty can be found at www.crestron.com/warranty.
The spe cific p atent s that cov er Crest ron product s are listed at www.crestron.com/legal/patents.
Certa in Crestron product s contain o pen source sof tware. For specific informat ion, vi sit www.crestron.com/opensource.
Crestron, the Crestro n logo, a nd FlipTop are eith er trademarks or regis tered tradema rks of Cre stron E lect ronics, Inc. i n
the United States and/or other countr ies. O ther trademarks, re gistered trad emark s, and trade names may be used in this
document to refer to eithe r the ent ities cl aiming the mark s and nam es or the ir products . Crest ron disc laims any proprietary
interes t in the marks and names of o thers . Crest ron is not responsible for errors i n typo graphy or photog raphy.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Dr ive, Rockleigh , NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Do c. 8511A
Specifications subject to
change without notice.
(205 4350)
09/06/19
Loading...