Power outlet module
FT2A-PWR-IT-1-BASIC
The retractable
Lid retraction button
FT2A-PWR-IT
AC Power Outlet Modules for FT2 Series
Suitable for use in Italy and other countries using Type L AC power outlets, the Crestron®
FT2 A‑PWR‑IT‑1‑BASIC and FT 2A‑PWR‑IT‑2 are modules designed for installation in Crestron
FT2 FlipTop™ cable management assemblies.
The outlet modules provide up to two Type L AC power outlets on top of the table. A
2.74 m (9 ft) power cord is fixed to the bottom of the module. The premium power module
(FT2A‑PWR‑IT‑2) provides two under‑the‑table receptacles for power switchers, HDBaseT®
transmitters, chargers, and other devices. Each module is rated for 10 A (total) at 220‑240 V,
50/60 Hz. The following table provides a size and feature comparison among models.
Module Model Module Slots Required Outlets on Top of the
Table
FT2A‑PWR‑IT‑BASIC 2 1 None
FT2A‑PWR‑IT‑2 4 2 2
FT2A-PWR-IT-1-BASIC FT2A-PWR-IT-2
Power outlet module
Outlets Beneath the
Table
Power cable (2)
254 mm (10 in.)
Install the Module
Install the power module into the FT2 FlipTop assembly. If the bezel and locking bars have not
been installed on the FT2 FlipTop assembly, skip to step 5.
NOTE: For ease of installation, install power outlet modules before installing any other module.
To install the power outlet module:
1. Tap the lid retraction button to retract the one‑touch lid, which disappears into the FT2
FlipTop assembly. If the assembly has two lids, retract both.
2. Remove and retain the magnetic bezel from the FT2 FlipTop assembly by grasping the
inside of the bezel and firmly pulling it up and away from the assembly until the magnetic
hold is broken.
3. Use a manual torque screwdriver to unscrew, remove and retain the two locking bars on
either side of the module row where the module is to be installed.
Remove Two Locking Bars
Locking bars (3)
7. Confirm that all modules are level with their surroundings and place the locking bars
(removed in step 3) into position so that the screws on either side engage the screw holes
in the assembly.
8. Use a manual torque screwdriver set to its lowest possible setting to tighten the locking
bar screws until the lock bars are secured to the FT2 FlipTop assembly.
9. Place the bezel (removed in step 2) onto the FT2 FlipTop assembly so that the retractable
lid fits inside the bezel opening. The bezel is held in place by magnets.
Attach the Bezel
lid fits inside
this opening in
the bezel.
Retractable lid
Check the Box
Power cord
2.74 m (9 ft)
Power receptacle (2)
457 mm (18 in.)
Power cord
2.74 m (9 ft)
4. Lift and remove the modules to be replaced.
5. Insert the new module’s power cable(s) through the empty module slots.
6. Orient the module as shown in the following illustration and slide it down into the
appropriate module slots. Use the guide ribs on the front and rear of the module to help
position it in the assembly.
Position the Module (FT2A-PWR-IT-1-BASIC shown)
Connect the Module
The FT2A‑PWR‑IT‑2 provides two Type L AC power receptacles beneath the table (the
FT2 A‑PWR‑IT‑1‑BASIC does not). Use these receptacles to provide power to an electrical FT2
FlipTop assembly and to devices installed below the surface within the FT2 FlipTop assembly
system.
To activate the power outlet module, insert the three‑prong plug into a nearby AC wall or floor
outlet.
Operate the Module
To operate the power outlet module:
1. Tap the lid retraction button to retract the one‑touch lid, which disappears into the FT2
FlipTop assembly.
2. Connect the device needing power to one of the available outlets on the module.
3. Confirm that the power indicator on the device shows that the device is receiving power.
Item Qty
FT2A-PWR-IT-1-BASIC or FT2A-PWR-IT-2 1
Additional Information
Scan or click the QR code for detailed product information.
FT2A‑PWR‑IT‑1‑BASIC FT2 A‑PWR‑IT‑2
Compliance and Legal
Original Instructions: The U. S. English version of thi s document is the o riginal instructi ons. All other l anguages are a translat ion
of the original instructions.
Regulatory Model: M201907002
As of the date of manufac ture, th e produc t has be en tested and fou nd to comp ly with s pecif ications for CE marking .
The Wast e Electrical & El ectronic Equi pment ( WEEE) d irect ive marking on a product indicates that i t should not be dis posed
of with general h ousehold waste. Inst ead, you a re encou raged to reuse or re cycle t he product in accordance with Directi ve
2012/19/EU of th e Europe an Union. Prope r disposal of thi s produc t will help preve nt potential negative e ffec ts on the
environment an d human health, which cou ld otherwis e be cause d by inapp ropriate waste handling. Penalties may be applicable
for incorrect disposal of this waste, in a ccordan ce with yo ur national legislat ion. Fo r information about rec ycling this pro duct,
please contact your household waste disposal service, your original distributor, or Crestron.
The product warranty can be found at www.crestron.com/warranty.
The spe cific p atent s that cov er Crest ron product s are listed at www.crestron.com/legal/patents.
Certa in Crestron product s contain o pen source sof tware. For specific informat ion, vi sit www.crestron.com/opensource.
Crestron, the Crestro n logo, a nd FlipTop are eith er trademarks or regis tered tradema rks of Cre stron E lect ronics, Inc. i n the
United States and /or other countrie s. HTB aseT is eith er a trademark or r egistered tra demark of the HD BaseT Alliance in
the United States and/or other countr ies. O ther trademarks, re gistered trad emark s, and trade names may be used in this
document to refer to eithe r the ent ities cl aiming the mark s and nam es or the ir products . Crest ron disc laims any proprietary
interes t in the marks and names of o thers . Crest ron is not responsible for errors i n typo graphy or photog raphy.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Dr ive, Rockleigh , NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Do c. 8503 A
Specifications subject to
change without notice.
(2054247)
08/14/19
Loading...