Page 1
DO GUIDE
DM-TX-200-C-2G
Wall Plate DigitalMedia 8G+® Transmitter 200
DO Make Connections to the Rear Panel
®
Make connections to the rear panel of the Crestron
into an electrical box (not included) or oor box (not included).
Ground
NOTE: The DM OUT port is a Power over DM (PoDM) and HDBaseT® PoE (Power over Ethernet)
powered device (PD) por t. To receive PoDM or HDBaseT PoE, the DM-TX-200-C-2G requires a
connection to a DigitalMedia™ switcher or other equipment that has a PoDM or HDBaseT PoE
power sourcing equipment (PSE) port. Any wiring that is connected to a PoDM or HDBaseT PoE
PSE port is for intrabuilding use only and should not be connected to a line that runs outside of
the building in which the PSE is located.
DM-TX-200-C-2G before installing the unit
24 Vdc from
power pack
(included)
To DM® switcher,
receiver, or other
DM device or to
®
device
HDBaseT
DO Install the DM-TX-200-C-2G
Install the DM-TX-200-C-2G into a 2-gang electrical box or into a 6-inch oor box.
DO Check the Box
QTY PRODUCT PART NUM.
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045866
4 Screw, #6-32 x 3/4", Truss Head, Combo 20 09211
Installation into a Floor Box
Install the DM-TX-200-C-2G into a 2-gang opening in a 6-inch (153 mm) deep oor box.
Using a Phillips head screwdriver, attach the DM-TX-200-C-2G to an installed oor box using
the four included #6-32 x 3/4-inch truss combo head screws.
Installation into an Electrical Box
Install the DM-TX-200-C-2G into a 2-gang electrical box in a wall, oor, or ceiling. A minimum
mounting depth of 2-1/2 inches (64 mm) is required.
To install the DM-TX-200-C-2G into an electrical box, do the following:
1. Using a Phillips head screwdriver, attach the DM-TX-200-C-2G to the electrical box using
the four included #6-32 x 3/4-inch truss combo head screws.
2. Attach a decorator-style faceplate (not included) to the front panel of the DM-TX-200-C-2G
using four screws (not included).
Page 2
DO Make Connections to the Front Panel
Make connections to the front panel of the DM-TX-200-C-2G as required for the application.
®
digital
HDMI
video/audio input
RGB (VGA), component,
S-video, or composite
video input
Unbalanced
stereo line level
audio input
Mouse/keyboard
input
PWR
AUDIO
IN
USB
HID
RESET
SETUP
8G LINK
8G ACTV
HDMI
PC
HDMI
IN
IN
PC
DO Set the IP Address
The conguration of the DM-TX-200-C-2G within the DigitalMedia 8G+® system determines how
the IP address of the DM-TX-200-C-2G is set:
• If the DM-TX-200-C-2G connects to a DigitalMedia switcher, the DM-TX-200-C-2G is
congured by the switcher automatically.
• If the DM-TX-200-C-2G connects to a DigitalMedia 8G+ receiver, the
DM-TX-200-C-2G uses its own conguration settings. By default, DHCP (Dynamic Host
Conguration Protocol) is enabled. If it is desired that the default IP address be assigned
to the DM-TX-200-C-2G, hold down the SETUP button while the unit boots up. The default
IP address 192.168.1.239 overwrites the current setting. To manually set a different IP
address, use the Crestron Toolbox™ application.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with spe cications for CE mar king.
This product is Listed to applicable UL Standards an d requirements teste d by Underwriters Laboratories I nc.
Ce produit est homologué selon les normes et l es exigences U L applicable s par Und erwriters Laboratori es Inc.
Federal Communications Commission (FCC) Compliance Statement
This device com plies with par t 15 of the FCC Rules. Op erati on is subject to the followi ng two co nditions:
(1) This devic e may not cause harmful interference, and (2) this devic e must ac cept any inter ference rece ived, in cluding inter ference
that may cause undesired operation.
CAUTION: Changes or modica tions not expre ssly approved by the manu facturer res ponsible for complia nce could void th e
user’s authority to operate the e quipment.
NOTE: This e quipment has b een tes ted and found to comply with the limi ts for a Class A digital dev ice, pursuant to part 15 of
the FCC Rul es. These limi ts are de signe d to provide reas onable protec tion against harmfu l inter ference when the equi pment
is operated in a co mmercial environme nt. Thi s equip ment ge nerates, use s and can radiate radio frequency energy and, i f not
installed and used in accord ance wi th the ins truction manual, may c ause ha rmful inter ference to radio communications. Operation
of this equipment in a residenti al area i s likely to c ause ha rmful i nterference in whic h case the user will be req uired to c orrect the
inter ference at his own expense.
DO GUIDE
Industry Canada (IC) Compliance Statement
CAN ICES-3(A)/NMB-3(A)
The speci c patents that c over Crestron pro ducts are listed a t patents.crestron.com. The produ ct warranty ca n be found at www.crestron.com/warranty.
Crestr on, the Crestron l ogo, Crestron Toolb ox, DigitalMedi a, DigitalMedi a 8G+, and DM are eithe r trademarks or regi stered trademar ks of Crestron E lectronics, Inc . in the United Sta tes and/or
other coun tries. HDB aseT and the HDBa seT logo are either tr ademarks or reg istered trade marks of the HD BaseT Alliance in th e United Stat es and/or other c ountries. HD MI and the HDM I logo are
either tr ademarks or regi stered trade marks of HDM I Licensing LL C in the United S tates and/or o ther countri es. UL and the U L logo are either t rademarks or r egistered tr ademarks of Und erwriter s
Labora tories, Inc. in the U nited States and /or other countrie s. Other trademar ks, registered tr ademarks, and trad e names may be used in this do cument to refer to eit her the entities clai ming
the marks a nd names or their prod ucts. Crestro n disclaims any propr ietary intere st in the marks and nam es of others. Cre stron is not respo nsible for errors in t ypography or ph otography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2016 Crestron Electronics, Inc.
DOC. 775 9B (2 043 30 6) 11.16
Specic ations subject to c hange without not ice.
Loading...