Crestron CNWP User Manual

CRESTRON CNWP Wired Panels

DESCRIPTION:

The CNWP series of wired panels, illustrated in figure 1, interfaces with a CRESNET II control system
over the CRESNET II network. The panels use miniature pushbuttons with self-contained feedback LEDs.
Some models include bargraph indicators. The CNWP panels are designed for lectern mounting and are
also available premounted in consolettes with black trim. Custom panel finishes, engraving, colored button
caps, and the omission of unused buttons are all standard.

1392345

94710 11 12 13

175518 19 20 21

256326 27 28 29

6 7 8 3334353637

14 15 16 41 42 43 44 45

22 23 24

30 31 32

50 51 52

49

58

57

59

60

53

61

38

46

54

62

40

48

56

@MUTE1

MUTE1

64

DOWN1 DOWN2

Figure 1. CNWP Series of Wired Panels

Configuration Differences

There are six wired panel configurations available and selection depends on type of installation (lectern or
consolette), number of buttons, and number of bargraphs. A configuration, CNWP, is defined by its suffix.
The number of buttons is identified by a dash and number. A "B" following the button suffix indicates
consolette versus lectern installation. If the suffix contains "BG2" before the button suffix, there are two
bargraphs on the unit. Refer to table 1 for a concise listing of each wired panel configuration.

BAR1 BAR2

@MUTE2

MUTE2

UP2UP1

CONFIGURATION INSTALLATION BUTTONS BARGRAPHS

CNWPBG2-32 Lectern 3 2 Two
CNWPBG2-64 Lectern 6 4 Two

CNWPBG2-32B Consolette 32 Two

REMOTE CONTROL SYSTEMS

Table 1. Wired Panel Configurations

CNWP-32 Lectern 3 2 None
CNWP-64 Lectern 6 4 None

CNWP-32B Consolette 32 None

1 DOC. 8008D

Specifications subject to change without notice.

CRESTRON CNWP Wired Panels

LEADING SPECIFICATIONS:

Table 2 provides a summary of leading specifications for wired panels. Dimensions and weight are
approximations rounded to the nearest tenth unit.

Table 2. Leading Specifications

SPECIFICATION DETAILS

CRESNET II Workshop Version 3.40 or later
CRESNET II Operating System SR30160.OPS or later
Cresnet Power Factor (CNWP-32)

(CNWP-64)
(CNWPBG2-32)
(CNWPBG2-64)
(CNWP-32B)
(CNWPBG2-32B)

Dimensions & Weight:

Permit 4.0 inch (10.2 cm) depth for all
lectern-mounted units. Consult factory for
lectern cut-out information.

CNWP-32

CNWP-64

CNWPBG2-32

CNWPBG2-64

CNWP-32B

CNWPBG2-32B

3.0 Watts

5.5 Watts

4.0 Watts

6.5 Watts

3.0 Watts

4.0 Watts

Height: 5.5 in (14.0 cm)
Width: 5.8 in (14.6 cm)
Height: 5.5 in (14.0 cm)
Width: 10.8 in (27.3 cm)
Height: 5.5 in (14.0 cm)
Width: 8.3 in (21.0 cm)
Height: 5.5 in (14.0 cm)
Width: 12.5 in (31.8 cm)
Height: 6.1 in (15.6 cm)
Width: 6.4 in (16.2 cm)
Height: 6.1 in (15.6 cm)
Width: 8.9 in (22.5 cm)

INSTALLATION/SETUP:

Identity Code

Each unique panel or component on the CRESNET II network requires the setting of an identity code (ID
CODE). ID CODES are two-digit hexadecimal numbers, from 03 to FE.

The ID CODE of the panel should be set to match the ID CODE specified in the NET.ID statement of the
CRESNET II SIMPL-C program referencing the panel (refer to SYNTAX section). To set an ID CODE,
disconnect power and remove the back of the panel. Accessible through the opening are two miniature

REMOTE CONTROL SYSTEMS

2 DOC. 8008D

Specifications subject to change without notice.