Physical Description 2
Leading Specifications 3
Setup 4
General Use and Safety 4
RF Identity Code 4
Programming (Cresnet and SmarTouch systems) 9
Programming in SIMPL Windows (Cresnet and SmarTouch systems) 11
Accessing the Inlay Card 18
Problem Solving 20
Troubleshooting 20
Further Inquiries 21
Return and Warranty Policies 22
Merchandise Returns / Repair Service 22
CRESTRON Limited Warranty 22
Appendix A: AT Scan Code 23
Operations Guide - DOC. 5700A Contents • i
CRESTRON
Wireless Mouse
Description
Functional Description
The wireless mouse is a hand-held user interface that uses radio frequency (RF) to
communicate with the CRESNET system, SmarTouch STS or the portable
SmartPresenter system. As part of the CRESNET system, the wireless mouse
communicates with the system via the CNRFGWA, RF receiver. As part of the
SmarTouch STS, the wireless mouse communicates with the system via the ST-CP,
control processor. When used with the SmartPresenter system, the wireless mouse
communicates with the system control processor, SP-1.
NOTE: The CNRFGWA must have PROM # 2251 for wireless mouse support. A
CNRFGWA with this PROM reports on the network with software version 2.00.
Early versions of the CNRFGWA do not support the wireless mouse.
Models
There are two CRESTRON wireless mice available: CNWM and CNWML. The
only difference between the two configurations is that one, the CNWML, is
equipped with a laser pointer. The laser can be turned ON and OFF by depressing
the center button (button 5) or button 4 on the keypad of the unit.
CNWM/L used with Cresnet
By design, the most logical application for the wireless mouse is as the user interface
in a presentation system. The wireless mouse and PC keyboard/mouse controller,
CNMK, can be added to control your PC presentation. These devices in conjunction
with CRESTRON’s simple-to-use Windows software improve the portability of the
user interface. They facilitate the transmission of programmed PC mouse and
keyboard operations as well as serial and IR device commands remotely.
CNWM/L used with SmarTouch
The CNWM/L can be used in a SmarTouch system. SmarTouch is a radio frequency
(RF) control system that offers unprecedented performance and value. Adding the
CNWML to the SmarTouch system offers keyboard and mouse emulation (with
optional CNMK) and multi-purpose AV control.
Operations Guide - DOC. 5700A Wireless Mouse • 1
™
CRESTRON
CNWM/L used with SmartPresenter™
The wireless mouse serves as the RF transmitter for the SmartPresenter
™ system.
This is a unique presentation system that is fully operational using the wireless
mouse. With only the compact SP-1 control processor and the wireless mouse, users
can control up to four IR devices and one RS-232 device. SmartPresenter has the
potential to control up to six functions per device. Functions are assigned to the four
positions of the mouse button, the mouse trigger, and the center keypad button on
the wireless mouse. The SmartPresenter system can be programmed easily in the
field using the CNWM/L. Refer to the SmartPresenter Quick Guide (DOC. 5742)
for additional information on field programming.
Physical Description
The wireless mouse, shown below, is housed in a black plastic enclosure that can
easily fit in the user’s palm. Nearly all the buttons, except for the trigger, can be
found on the topside of the unit. The trigger can be found on the bottom of the unit.
Button placement has been carefully designed into the unit for ease of use.
Wireless Mouse Physical Views
Mouse
Button
Trigger
(button 6)
6.036"
153.31mm
1.775"
1.775"
45.09mm
45.09mm
CNWML
Lazer
Button
5.331"
135.41mm
1.775"
45.09mm
CNWM
Device
Buttons
(lg. btn. 5)
1.362"
34.59mm
Notice the lined paper beneath the clear plastic cover that surrounds the keypad
buttons. Once functionality has been assigned to the keypad buttons, a brief
description can be written on the lined paper. For a more professional look, a label
kit (SP-LK) is available for the wireless mice. The SP-LK label kit provides a sheet
of the most common control functions and several pre-cut mouse inlay cards.
To access the inlay card, refer to "Accessing the Inlay Card" on page 18.
Two AAA-sized batteries are provided with the wireless mouse. Access to the
battery compartment is permitted after the battery cover is removed. A sensor (photo
transistor) used to program the RF identity code is also located in the battery
compartment.
2 • Wireless Mouse Operations Guide - DOC. 5700A
CRESTRON
Battery Compartment (Rear View)
Leading Specifications
The table below provides a summary of leading specifications for the wireless
mouse. Dimensions and weight are approximations rounded to the nearest
thousandth unit.
Leading Specifications of the Wireless Mouse
SPECIFICATIONDETAILS
Battery
SIMPL™ Windows
CRESNET Operating System
CNRFGWA Software
SmarTouch (ST-CP) Operating
System*
SmarTouch (ST-CP) Monitor Version* 1.29 or later
VisionTools Pro™
Dimensions & Weight
(without batteries)
* NOTE: Upload the SmarTouch Monitor before uploading the SmarTouch
Operating System.
2 disposable "AAA" cells
®
Version 1.18 or later
3.17.29 or later
version 2.00/PROM # 2251
4.00.38-s or later
Version 1.1.3 or later
Height: 5.331 in (13.541 cm) for CN-WM
6.036 in (15.33 cm) for CN-WML
Width: 1.775 in (4.509 cm)
Depth: 1.380 in (3.505 cm)
Weight: 0.140 lb (0.064 kg) for CN-WM
0.270 lb (0.122 kg) for CN-WML
Laser Specifications of the CNWML
SPECIFICATIONDETAILS
Wavelength
Output Power
Operations Guide - DOC. 5700A Wireless Mouse • 3
670 nm (Class IIIa Product)
Less than 5 mW
CRESTRON
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. The equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
As of the date of manufacture, the unit has been tested and found to comply with
specifications for CE marking.
Setup
General Use and Safety
DANGER: The CNWML contains a Class IIIa laser. Avoid direct eye exposure.
Compliance to the following suggestions may extend the life of the wireless mouse
and laser.
• If the unit is not going to be used for a month or longer, remove
batteries. Never leave weak or dead batteries in the unit; they might
leak chemicals that can damage the unit.
• Use care when handling the unit. Dropping the unit can unfocus the
lens, damage circuit boards, and cause the unit to work improperly.
• Operate and store the unit in moderate temperatures. Do not place the
unit in environments below freezing or exceeding 110°F. Temperature
extremes can shorten the life of electrical devices, damage the batteries,
and distort or melt plastic parts.
• Keep the unit away from dust and dirt that can cause premature wear
on parts. Use a damp cloth to wipe the unit. Do not use harsh
chemicals, cleaning solvents, or strong detergents to clean the device.
RF Identity Code
Every hand-held wireless transmitter communicating with either the SmartPresenter,
ST-CP or CNRFGWA requires a unique RF identity (ID) code. The code is a two-
4 • Wireless Mouse Operations Guide - DOC. 5700A
CRESTRON
digit hexadecimal number. To maintain code diversity within a system, use codes
between 10 and FE for the transmitters. There are two methods to change the RF ID
code on the wireless mouse: via the CNIDC (Identity Code Cable) and Viewport
software or depressing buttons on the unit that represent a binary code.
NOTES: The RF ID CODE on the wireless mouse is factory set to 30.
Only use 10 through FE as RF ID code.
Do not confuse RF ID with network (NET) ID.
Match CNWM/L ID to SP-1 Receiver
(SmartPresenter)
Depress and hold the recessed button #1 on the SP-1 for at least 5 seconds (use a
paper clip or similar object) or until the red RF LED flashes on the SP-1.
Depress (position A) button on the CNWM/L while the RF LED flashes.
Observe that RF LED stops flashing and remains illuminated for about 4 seconds.
NOTE: An extinguished LED indicates a match of CNWM/L ID to that of the SP-1.
If the RF ID does not match, refer to "Change RF ID via CNWM/L Button Presses"
on page 7.
Verify RF ID with Crestron Software
(not required for SmartPresenter)
Use the Crestron Performance VeiwPort to view transmitter ID codes. Using either
SIMPL Windows or VisionTools Pro, select ViewPort from the Tools menu; the
“Crestron Performance Viewport” dialog box, shown below, appears.
From the Diagnostics menu in the dialog box, select Identify Transmitter ID to
open the “Transmitter Identification” dialog box. Press a button on the transmitter,
ViewPort will display the transmitter ID in hexadecimal format.
Operations Guide - DOC. 5700A Wireless Mouse • 5
CRESTRON
Change RF ID Crestron Software
(not required for SmartPresenter)
Use the Crestron Performance ViewPort to set a RF ID CODE. Using either SIMPL
Windows or VisionTools Pro, select ViewPort from the Tools menu; the “Crestron
Performance Viewport” dialog box, shown below, appears.
Crestron Performance Viewport Dialog Box
From the Options menu in the dialog box, select Set Transmitter ID to open the
“Set Transmitter ID” dialog box. Enter a two-digit hexadecimal number ranging
from 10 to FE. Click OK to confirm.
Set Transmitter ID Dialog Box
6 • Wireless Mouse Operations Guide - DOC. 5700A
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.