Page 1
Page 2
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
Page 3
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Contents
7 Channel Surround-Sound Amplifier: CNAMPX-7X200 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................ 1
Specifications ..............................................................................................................2
Physical Description.................................................................................................... 3
Industry Compliance ...................................................................................................4
Setup .......................................................................................................................................... 5
Rack Mounting ............................................................................................................ 5
Network Wiring........................................................................................................... 6
Identity Code ............................................................................................................... 7
Hookup ........................................................................................................................ 7
Typical System Configuration..................................................................................... 8
Programming .............................................................................................................................9
Programming with the Crestron AppBuilder...............................................................9
Programming with SIMPL Windows.......................................................................... 9
Problem Solving ......................................................................................................................13
Troubleshooting......................................................................................................... 13
Further Inquiries........................................................................................................ 14
Firmware Upgrades ...................................................................................................14
Future Updates ..........................................................................................................14
Return and Warranty Policies.................................................................................................. 15
Merchandise Returns / Repair Service ......................................................................15
CRESTRON Limited Warranty.................................................................................15
Operations Guide - DOC. 8179 Contents • i
Page 4
Page 5
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
•
7 Channel Surround-Sound
Amplifier: CNAMPX-7X200
Introduction
Features and Functions
The CNAMPX-7X200 is a high-powered, 7 channel amplifier that delivers 200
Watts per channel. Designed for surround-sound configurations that incorporate a
powered subwoofer, it is ideally suited for home theaters, large rooms, or multi-room
locations, to provide the authentic cinema experience for everything from action
movies to classic films. Like all Crestron CNAMPX intelligent amps, it runs over the
Cresnet control network. Designed for professional quality and ultimate reliability,
the CNAMPX-7x200 is an integral component of the Crestron Home
distribution solution. The CNAMPX-7X200 produces all the crystal clear highs and
rich lows that serious audiophiles demand and is ideal for use with Crestron’s CNXDAP8 or CNX-DAP8RC surround sound processors.
™
audio
As part of a Cresnet system, the unit can accept remote power on/off commands and
reports ambient temperature within the enclosure. Temperature is available as
Fahrenheit or Celsius and the signal can be used under program control to reduce the
audio volume, activate an external cooling fan, or turn the unit off.
Functional Summary
7 Channels of Amplification
− 200 Watts/Channel Stereo into 8 Ohm Load (300
Watts into 4 Ohms)
− Flat within +0, -0.1 dB from 20 Hz to 20 KHz
− SNR “A” Weighted > 100dB
− SMPTE IM Distortion 0.05%
• Designed to be used in a system that includes a powered
subwoofer
• Ideal for use with CNX-DAP8 or CNX-DAP8RC
surround-sound processors
• Provides authentic cinema experience in home theaters
or large rooms
All audio connectors are gold plated to minimize oxidation. Two types of wire
terminations can connect to the audio outputs. A highly efficient toroid transformer
provides ample power to the amplifier modules. No fans are required, but if the unit
is placed in a rack configuration, it must have a minimum of one rack space above
and below for adequate ventilation.
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 1
Page 6
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
The CNAMPX-7X200 is also available in an international version. All of the features
are identical with the exceptions of the international AC power requirements, the
power rating of the Master Switch circuit breaker, the power cord and the unit
nomenclature of CNAMPXI-7X200. Throughout this operations guide, all references
to CNAMPX-7X200 apply to both versions except where noted.
Specifications
The following table provides specifications for the CNAMPX-7X200 and
CNAMPXI-7X200.
CNAMPX-7X200 Specifications
SPECIFICATION DETAILS
Power Input Requirements: US version
International version
Cresnet Power Requirements 3 Watts (24VDC @ 0.125A)
Default NET ID 3F
Channels 7
Output Power – All channels driven, 20Hz
to 20KHz, at rated THD
Input Impedance 28K ohms
Power Bandwidth – 3dB 3Hz to 150KHz
Frequency Response @ 1W 8ohm Flat +0, -0.1dB from 20Hz to 20Khz
Total Harmonic Distortion @ full power 0.02% or less
SMPTE I.M. Distortion @ full power 0.05% or less
Signal to Noise Ratio (S/N) “A” Weighted > 110dB
Gain 28dB
Damping Factor > 1000
Channel Separation over full bandwidth > 100dB
Environmental Temperature &
Humidity
Rack Space Required 4U (not including free rack space above and
Master Switch 20-Amp Magnetic Circuit Breaker (US version)
Control System Update Files
2-Series Control System Update
CEN/CN-TVAV Update File
CNMSX-AV/Pro Update File
CNRACKX/-DP Update File
ST-CP Update File
Dimensions & Weight Height: 7.70 in (19.56 cm)
1. The latest versions can be obtained from the Downloads | Software Updates page of the Crestron
website (www.crestron.com)
2. Crestron 2-Series control systems include the AV2 with CAGE2, PAC2, PRO2, and RACK2.
3. CNX update files are required for either CNMSX-AV/Pro or CNRACKX/-DP. Filenames for CNX
update files have a UPZ extension and ST-CP files are in one EXE or zipped UPZ file. To avoid
program problems, make certain you are using the update file with the correct suffix letter (e.g., S, V,
W, X).
1, 2, 3
. Refer to NOTE after last footnote.
120 VAC ±10%, 60 Hz, 2400 Watts, 20 Amps max.
230 VAC ±10%, 50 Hz, 2400 Watts, 10 Amps max.
200 Watts/Channel into 8-ohm loads
300 Watts/Channel into 4-ohm loads
41 to 104° F (5 to 40°C)
10 to 90% RH (non-condensing)
below)
10-Amp Magnetic Circuit Breaker (Int’l version)
Version C2-1001.CUZ or later
Version 5.10.13V.UPZ or later
Version 5.10.11X.UPZ or later
Version 5.10.11W.UPZ or later
Version 4.01.04S.UPZ or later
Width: 19.0 in (48.26 cm) – with ears
17.18 in (43.64 cm) – without ears
Depth: 18.88 in (47.95 cm)
Weight: 94.4 lb (42.48 kg)
NOTE: Crestron software and any files on the FTP site are for Authorized Crestron
dealers only. New users may be required to register to obtain access to certain areas
of the FTP site.
2 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
Page 7
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Physical Description
The CNAMPX-7X200 is housed in a black enclosure with labeling on the front and
rear panels. The enclosure consists of 13-gauge powder-coated steel with stainless
steel screws. The front panel contains the main power switch with built-in lightemitting diode (LED). All audio input and output, Cresnet system, and power
connections are made on the rear panel. Four rubber feet on the base of the unit
provide stability and prevent slippage in shelf placement or stacked configurations.
Front and Rear Panels
CNAMPX-7X200 Front Panel
CNAMPX-7X200 Rear Panel
Ports, Indicators, and Controls
The ports, indicators, and controls provided on the front and rear of the CNAMPX7X200 are described below.
PWR Indicator
This LED (green) is illuminated when 24VDC is supplied via the Cresnet connector.
NET Indicator
This LED (yellow) indicates that the SIMPL program currently loaded in the control
system has a network device defined at the same NET ID code as the CNAMPX7X200.
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 3
Page 8
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
(Chassis Ground)
Use this chassis screw to connect the audio device(s) common ground(s) to the
CNAMPX-7X200.
NET
The 4-pin network connector is used to connect the CNAMPX-7X200 to the Cresnet
system. Refer to “Network Wiring” on Page 6 when making connections to the ports
labeled NET.
OVERRIDE/SETUP Button and Indicator
The OVERRIDE/SETUP button is used to activate AC power to the CNAMPX7X200 and activate the room outputs, overriding program control. This button
functions only when 24VDC is applied to the NET connector; the Master Switch and
front panel POWER switch must also be set to their On positions. The LED (red)
illuminates when the OVERRIDE function is activated.
Power Connector
Provides AC operating power to the CNAMPX-7X200. The connector is a 20 Amp
IEC connector. U.S. models require a dedicated 20-Amp line and receptacle. Use
only the supplied power cord, or equivalent, to connect to the AC power source.
Master Switch
This 20-amp magnetic circuit breaker (10-amp on international version) electrically
protects the internal circuitry from power overloads.
INPUTS
The seven gold plated RCA connectors are typically used to connect single-ended,
line-level pre-amplified audio to the CNAMPX-7X200.
4 – 8 OHM OUTPUTS
These seven pairs of speaker dual-binding posts output the amplified audio to the
speakers. The audio positive posts have red screw-on caps and the audio negative
posts have black screw-on caps. Each post is gold-plated and accepts bare wire or
banana plugs.
Front Panel Power Switch
The front panel of the CNAMPX-7X200 contains a power switch with an LED
indicator. This two-position switch turns operating power to the CNAMPX-7X200
circuitry on and off. It must be positioned to ON when the unit is to be controlled by
the control system. When the Cresnet system 24VDC is applied to the NET
connector on the rear panel and this switch is set to ON, AC power is applied to the
unit and the switch’s LED (green) illuminates.
Industry Compliance
As of the date of manufacture, this unit has been tested and found to comply with
specifications for CE marking and standards per EMC and Radio Communications
Compliance Labeling (N11785)
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
4 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
Page 9
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Setup
WARNING: To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety.
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
When mounting this unit assembly in a partially filled rack, load the rack from
the bottom to the top with the heaviest component at the bottom of the rack.
CAUTION: Due to the heat dissipation of the CNAMPX-
7X200 (and all audio
amplifiers in general), allow at least one free rack space above and below the
CNAMPX-7X200 for proper circulation.
NOTE: Reliable grounding of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit. (e.g., use of power strips).
Rack Mounting
Two “ears” are provided with the unit and must be installed so that it can be rack
mounted. Refer to the following illustration and complete the procedures below to
attach ears to the unit. The only tool required is an Allen wrench (supplied).
Ear Attachment for Rack Mounting
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 5
Page 10
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
1. Using the supplied Allen wrench, remove and retain the three side
screws closest to the front panel.
2. Position a rack ear so that its mounting holes align with the vacated
holes, and secure the ear to the unit with the three screws from step 1.
3. Repeat the procedure to attach the remaining ear to the opposite side.
Network Wiring
NOTE: When installing network wiring, refer to the latest revision of the wiring
diagram(s) appropriate for your specific system configuration, available from the
Downloads | Product Manuals | Software and Wiring Diagrams section of the
Crestron website (www.crestron.com)
When calculating the wire gauge for a particular Cresnet run, the length of the run
and the power factor of each network unit to be connected must be taken into
consideration. If Cresnet units are to be daisy-chained on the run, the power factor of
each unit to be daisy-chained must be added together to determine the power factor
of the entire chain. If the unit is a home-run from a Crestron system power supply
network port, the power factor of that unit is the power factor of the entire run. The
length of the run in feet and the power factor of the run should be used in the
following resistance equation to calculate the value on the right side of the equation.
Resistance Equation
.
40,000
Where:
R <
L x PF
The required wire gauge should be chosen such that the resistance value is less than
the value calculated in the resistance equation. Refer to the table below.
Wire Gauge Values
R = Resistance (refer to table below).
L = Length of run (or chain) in feet.
PF = Power factor of entire run (or chain).
RESISTANCE (R) WIRE GAUGE
4
6
10
15
13
8.7
NOTE: All Cresnet wiring must consist of two twisted-pairs. One twisted pair is the
+24V conductor and the GND conductor and the other twisted pair is the Y
conductor and the Z conductor. .
NOTE: When daisy-chaining Cresnet units, strip the ends of the wires carefully to
avoid nicking the conductors. Twist together the ends of the wires that share a pin on
the network connector, and tin the twisted connection. Apply solder only to the ends
of the twisted wires. Avoid tinning too far up the wires or the end becomes brittle.
Insert the tinned connection into the Cresnet connector plug and tighten the retaining
screw. Repeat the procedure for the other three conductors.
16
18
20
22
Doubled CAT5
Tripled CAT5
6 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
Page 11
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Identity Code
Every equipment and user interface within the Cresnet system requires a unique
identity code (NET ID). These codes consist of a two-digit hexadecimal number
from 03 to FE. The NET ID of the unit must match an ID code specified in the
SIMPL Windows program. The NET ID of the CNAMPX-7X200 is factory set to 3F.
The NET IDs of multiple CNAMPX-7X200s in the same system must be unique.
NET IDs are changed from a personal computer (PC) via the Crestron Viewport.
Complete the following steps to change the NET ID.
NOTE: For detailed information on establishing communication between the PC
and Control System, refer to the network’s Control System Operations Guide.
1. Ensure that the CNAMPX-7X200 is the only device connected to the
control system (verify that the software is running).
2. Open the Crestron Viewport.
3. From the Viewport menu, select Functions | Set Network ID. The
software checks the baud rate and then opens the “Set Network ID”
window.
4. In the “Set Network ID” window, select the CNAMPXCurrent Network Devices text window.
5. From the Choose the new network ID for the selected device (Hex): text
box, select the new Net ID for the CNAMPX-
6. Click Set ID to initiate the change. This will display the “ID command
has been sent” window.
7. In the “Command Complete” window, click OK.
8. In the Current Network Devices text window, verify the new NET ID
code.
9. In the “Set Network ID” window, click Close.
NOTE: The new NET ID code may also be verified by selecting Diagnostic |
Report Network Devices in the Viewport (alternately, select F4).
10. Repeat this procedure for each CNAMPX-7X200 to be added to the
system.
7X200.
7X200 from the
Hookup
Refer to the following suggested configuration diagram, and make the connections to
the input and output connectors of the CNAMPX-7X200 amplifier appropriate for
the intended operation of the unit. Other than making the power connection last,
complete the connections in any order. The power cord is supplied, but RCA audio
cables, speaker wire, or Cresnet cables are not provided.
NOTE: Each of the seven amplifier channels are functionally identical and can be
connected to a surround-sound processor in any convenient arrangement.
NOTE: Refer to “Network Wiring” on page 6 when making connections to the port
labeled NET.
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 7
Page 12
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
NOTE: U.S. models require a dedicated 20-Amp line and receptacle. Use only the
supplied power cord, or equivalent, to connect to the AC power source.
Suggested Hookup Connections for the CNAMPX-7X200
SURROUND SOUND PROCESSOR
SIDE REAR CENTER
FRONT
L
R
SURROUND SOUND OUT
SURROUND SOUND OUT
CNAMPX-7X200 SURROUND SOUND AMPLIFIER
CNAMPX-7X200 SURROUND SOUND AMPLIFIER
LEFT
FRONT
RIGHT
FRONT
LEFT
SIDE
RIGHT
SIDE
Typical System Configuration
SUBWOOFER
SUBWOOFER
LEFT
REAR
RIGHT
REAR
SUBWOOFER
CENTER
(FRONT)
TO
The following figure shows a typical head-end/room audio configuration using the
CNAMPX-
8 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
7X200.
Page 13
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
p
Programming
You can create a program that allows you to control the CNAMPX-7X200 through a
Crestron control system using the Crestron programming tools Crestron Application
Builder™ (AppBuilder) and SIMPL™ Windows®. These tools are intended for users
with different levels of programming knowledge. The flexibility of each tool is
proportional to the degree of programming expertise (i.e., the more flexible, the more
a programmer needs to know and account for). Of course, one can initiate
programming using the easiest method (Crestron AppBuilder) and use advanced
techniques that are available from SIMPL Windows to customize the job.
The following are recommended software version requirements for the PC:
• SIMPL Windows version 2.01.05 or later. Requires SIMPL+ Cross
Compiler version 1.1.
• Crestron Database version 15.6.8 or later.
• Application Builder version 1.0.9 or later. Requires SIMPL Windows.
Programming with the Crestron AppBuilder
The easiest method of
rogramming, but does not
offer as much flexibility as
SIMPL Windows.
The Crestron AppBuilder offers automatic programming for such residential and
commercial applications as audio distribution, home theater, video conferencing, and
lighting. The interface of this tool guides you through a few basic steps for
designating rooms and specifying the control system, touchpanels, devices, and
functionality. The Crestron AppBuilder then programs the system, including all
touchpanel projects and control system logic.
The Crestron AppBuilder is fully integrated with Crestron's suite of software
development tools, including SIMPL Windows, VT Pro-e, Crestron Database, User
IR Database, and User Modules Directory. The Crestron AppBuilder accesses these
tools behind the scenes, enabling you to easily create robust systems.
Programming with SIMPL Windows
NOTE: The following assumes that the reader has knowledge of SIMPL Windows.
If not, refer to the extensive help information provided with the software.
NOTE: In the following, the PRO2 control system is used.
SIMPL Windows is Crestron's software for programming Crestron control systems.
It provides a well-designed graphical environment with a number of workspaces
(i.e., windows) in which a programmer can select, configure, program, test, and
monitor a Crestron control system. SIMPL Windows offers drag and drop
functionality in a familiar Windows
This section explains how to create a SIMPL Windows program that includes the
CNAMPX-7X200.
Configuration Manager is where programmers “build” a Crestron control system by
selecting hardware from the Device Library. In Configuration Manager, drag the
PRO2 from the Control Systems folder of the Device Library and drop it in the upper
pane of the System Views. The PRO2 with its associated communication ports is
displayed in the System Views upper pane.
environment.
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 9
Page 14
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
PRO2 System View
The System Views lower pane displays the PRO2 system tree. This tree can be
expanded to display and configure the communications ports.
Expanded PRO2 System Tree
C2Net-Device Slot in Configuration Manager
The C2Net-Device Slot can accept an amplifier such as the CNAMPX-7X200. Once
the amplifier is configured in a C2Net-Device Slot, the slot allows Cresnet
communication between the amplifier and the control system.
In Configuration Manager, drag the CNAMPX-7X200 from the Cresnet Control
Modules | Cresnet Audio Modules folder of the Device Library and drop it on the
PRO2 C2Net-Device slot in System Views. The System Views upper pane displays
the CNAMPX-7X200 device icon below the PRO2 graphic. The PRO2 system tree
displays the amplifier in Slot 9, with a default NET ID of 3F.
C2Net Device, Slot 9
Double-click the CNAMPX-7X200 icon in the upper pane to open the “Device
Settings” window. This window displays CNAMPX-7X200 device information. The
NET ID can be changed in this window using the NET ID tab.
10 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
Page 15
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Device Settings Window
NOTE: SIMPL Windows automatically resets the default NET ID values of a
device added to a program if a duplicate device or a device with the same default
NET ID already exists in the program. Always ensure that the network device NET
IDs set via Viewport match the ones in your SIMPL Windows program.
CNAMPX-7X200 Symbol in Programming Manager
Programming Manager is where programmers “program” a Crestron control system
by assigning signals to symbols. The diagram below shows the CNAMPX-7X200
symbol in the Detail View of the Programming Manager.
Detail View of the CNAMPX-7X200 Symbol in SIMPL Windows Programming Manager
The two tables on the next page list the input and outputs, respectively, and their
functional descriptions.
NOTE: All signals listed in the following tables are DIGITAL signals unless noted
otherwise. A digital signal can be high (logic level of 1), low (logic level of 0), and
also have rising edge (when it goes from low to high) and falling edge (from high to
low) transitions. Depending upon how the symbol was created, symbol inputs may
work at the logic levels or on transitions.
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 11
Page 16
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
CNAMPX-7X200 Symbol Input Signal Descriptions
INPUT DESCRIPTION
Main_Power This signal activates the main operating power to the CNAMPX-
7X200 circuitry. (Master Switch and front panel POWER switch
must be set to On.)
High/1=power on
Low/0=power off
Enable_Temp_Rpt This signal selects whether or not the Temp(x10) analog output
described in the next table is updated with the CNAMPX-7X200
enclosure temperature.
High/1 = update temperature
Low/0/default = temperature not updated
Temp_Format This signal selects the format of the temperature to be displayed.
High/1 = Celsius
Low/0/default = Fahrenheit
CNAMPX-7X200 Symbol Output Signal Descriptions
OUTPUT DESCRIPTION
OverRide_F This signal indicates that the audio output override function is
activated.
High/1 = override active
Low/0 = override not active
Temp(x10)
(analog)
The OverRide_F signal is typically used to provide a visual indication (e.g., on a
Touchpanel screen) that the Override function has been selected, preventing program
control of the audio output. The temperature report signal is typically used under
program control to activate amplifier power shutoff when the temperature reaches a
predetermined level.
This analog signal corresponds to the ambient temperature
within the CNAMPX-7X200 enclosure. The temperature reports
approximately once every 2-seconds. (The Enable_Temp_Rpt
entry in previous table must be driven high/1 for this to update.)
The temperature reports in tenths of a degree (eg, 725
corresponds to 72.5 degrees).
Example Program
An example program for the CNAMPX-7X200 is available from the Crestron FTP
site (www.ftp.crestron.com)
CNAMPXE1.ZIP.
12 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
. Select the Examples folder and search for
Page 17
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Problem Solving
Troubleshooting
The table below provides corrective action for possible trouble situations. If further
assistance is required, please contact a Crestron customer service representative.
CNAMPX-7X200 Troubleshooting
TROUBLE
No functions and
no indicators
illuminate.
Green PWR LED
does not illuminate.
Yellow NET LED
does not illuminate.
Hum on audio. Grounding problem. Either connect or remove chassis ground
Audio is supplied to
room regardless of
programming.
Audio distorted or
not present at room
output.
POSSIBLE
CAUSE(S)
CNAMPX-7X200 is
not receiving VAC
power.
CNAMPX-7X200 is
not receiving 24VDC
Cresnet power.
CNAMPX-7X200 in
SIMPL Windows
program not properly
configured.
CNAMPX-7X200 is
not receiving 24VDC
Cresnet power.
Improper NET ID. Verify that CNAMPX-7X200 NET ID
Override/Setup
function selected.
Audio input cable(s)
loose or not
connected.
Room output
(speaker) wire(s)
loose or not
connected.
Verify that POWER switch is positioned to
ON, AC power cord is plugged into
CNAMPX-7X200 power port and cord is
plugged into a good power source.
Reset Master Switch circuit breaker.
Verify that 24VDC is present at cable
plugged into NET port.
Verify SIMPL Windows CNAMPX-7X200
program.
Verify that 24VDC is present at cable
plugged into NET port.
matches NET ID in software program.
wire; remove AC ground.
Press OVERRIDE/SETUP button on rear
panel of CNAMPX-7X200.
Verify that audio input cables plugged into
INPUTS ports are secure.
Verify that speaker wires connected to
OUTPUTS terminals are secure.
CORRECTIVE ACTION
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 13
Page 18
7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
Further Inquiries
If after reviewing this Operations Guide you cannot locate specific information or
have questions, please take advantage of Crestron's award winning customer service
team by calling:
• In the US and Canada, call Crestron’s corporate headquarters at
1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400.
• In Europe, call Crestron International at +32-15-50-99-50.
• In Asia, call Crestron Asia at +852-2341-2016.
• In Latin America, call Crestron Latin America at +5255-5093-2160.
• In Australia and New Zealand, call Crestron Pacific at
+613-9480-2999.
Firmware Upgrades
To take advantage of all the CNAMPX-7x200 features, it is important that the unit
contains the latest firmware available. Therefore, please check our website
(http://www.crestron.com/downloads/software_updates.asp) for the latest version of
firmware. Not every product has a firmware upgrade, but as Crestron improves
functions, adds new features, and extends the capabilities of our products, firmware
upgrades are posted. For questions regarding upgrade procedures, contact Crestron
customer service.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the CNAMPX-7X200, additional information and programming examples may be
made available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation
revision.
Check the Crestron website (www.crestron.com
availability and its subjective value. Updates are available from the Downloads |
Product Manuals section and are identified as an “Addendum” in the Download
column.
) periodically for manual update
14 • 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179
Page 19
Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange, or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number, and
return address.
2. Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, Cresskill, N.J., or its authorized subsidiaries, with RMA number
clearly marked on the outside of all cartons. Shipments arriving freight collect or without an
RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and
absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products
returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1)
year; touchscreen display and overlay components are covered for 90 days; batteries and
incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the
dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in
any application other than that for which it was intended, or if it has been subjected to misuse,
accidental damage, modification, or improper installation procedures. Furthermore, this warranty
does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for
any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be
covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed
or implied, nor authorizes any other party to offer any other party to offer any warranty, including
any implied warranties of merchantability or fitness for a particular purpose. Any implied
warranties that may be imposed by law are limited to the terms of this limited warranty. This
warranty statement supercedes all previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft
Corporation.
Operations Guide – DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 • 15
Page 20
Crestron Electronics, Inc. Operations Guide – DOC. 8179
15 Volvo Drive Rockleigh, NJ 07647 04.02
Tel: 888.CRESTRON
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...