
infiNET™ DIMMERS
Introduction
Features and Functions
The CLW-DIM1RF (-DIM1RF) and CLW-DIM4RF
(-DIM4RF) are stand-alone wall box dimmers that can
also act as wireless infiNET™ devices that report to a
Crestron
such as the Crestron C2N-MNETGW. The -DIM1RF and
-DIM4RF have three preset lighting levels that can be
adjusted. For more information, refer to the latest version
of the infiNET Dimmers Operations Guide (Doc. 6396)
which is available from the Crestron website
(www.crestron.com/manuals).
These dimmers are part of Crestron’s line of lighting
products using infiNET mesh network technology.
infiNET technology is “Wi-Fi” friendly and provides fault
tolerance and increased effective signal strength as
network devices are added.
Up to 30 infiNET devices (including C2N-MNETRPT
infiNET Repeaters) can communicate with one
C2N-MNETGW Gateway. If more devices are needed,
more C2N-MNETGW gateways may be added to a
Cresnet
The infiNET dimmers operate on the 2.4 GHz “ISM
band” (2400 MHz to 2483.6 MHz) at 10 mW. The output
power of these devices allow RF signals to travel
approximately 150 feet indoors and 250 feet outdoors
(subject to site-specific conditions) without the use of
repeaters or other infiNET devices. The range is
dependent on construction of the building, obstructions,
and RF interference from other devices. The location of
the dimmer is an important factor in determining RF
performance. Adding more infiNET devices or repeaters
to the network effectively increases the range, strength,
and reliability of the network.
The -DIM1RF and -DIM4RF feature a three-position
mode selection switch. For more information, refer to the
latest version of the infiNET Dimmers Operations Guide
(Doc. 6396) which is available from the Crestron website.
In the absence of control system communications, the
dimmer can still be used to control the attached load.
The CLW-DIMS1RF (-DIMS1RF) and CLW-DIMS4RF
(-DIMS4RF) are similar to the -DIM1RF and -DIM4RF
(respectively) with the added capability of working with
one or more slave units (CLW-SLVD1RF) in a multidimmer / single circuit application.
®
control processor through an infiNET gateway
®
network.
connect to a Cresnet system and cannot be used without a
-DIMS1RF or -DIMS4RF. The -SLVD1RF does not have
a mode selection switch. It will emulate the RUN mode of
the -DIMS1RF (even if connected to a -DIMS4RF) unless
the mode selection switch of the master is set to “OFF”.
For more information, refer to the latest version of the
infiNET Dimmers Operations Guide (Doc. 6396) which is
available from the Crestron website.
These dimmers are available in white, almond, and black.
White units are designated by part numbers ending in
“W”. Almond units are designated by part numbers
ending in “A”. Black units are designated by part numbers
ending in “B”. Each dimmer can be covered with a
decorative faceplate (not supplied).
Specifications
Following are specifications for the -DIM1RF, -DIM4RF,
-DIMS1RF, -DIMS4RF, and -SLVD1RF.
CLW-DIM1RF/-DIM4RF, CLW-DIMS1RF/-DIMS4RF, &
CLS-SLVD1RF Specifications
SPECIFICATION DETAILS
Power Requirements Line Power, 120 VAC, 60 Hz
Operating Frequency 2400 MHz to 2483.6 MHz
RF Output Power 10 mW
Operating Ranges¹
Typical Distance
Indoors
(without repeater)
Typical Distance
Outdoors
Default MNET ID -DIM1RF/-DIM4RF: 01/01
Switch Type Dimmer
Load Type Incandescent, Tungsten-
2-Series Control System
Update File
Load Ratings4
Incandescent/Tungsten-
Halogen
Magnetic Low Voltage5 -DIM1RF/-DIM4RF:
(continued on following page)
2,3
(802.15.4 compliant)
150 ft
250 ft
(subject to site-specific
conditions)
-DIMS1RF/-DIMS4RF: 01/01
Halogen, Magnetic Low Voltage
Version 3.154 or later
-DIM1RF/-DIM4RF: 1000W
-DIMS1RF/-DIMS4RF: 1000W
-SLVD1RF: N/A
1000VA/750W
-DIMS1RF/-DIMS4RF:
1000VA/750W
-SLVD1RF: N/A
The CLW-SLVD1RF (-SLVD1RF) is a slave unit that
when used in conjunction with the -DIMS1RF or
-DIMS4RF acts as an additional dimmer control point in a
multi-dimmer / single circuit application. It does not
Crestron Electronics, Inc. Installation Guide – DOC. 6292A
15 Volvo Drive Rockleigh, NJ 07647 (2011321)
Tel: 888.CRESTRON 09.06
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.

infiNET™ DIMMERS
CLW-DIM1RF/-DIM4RF, CLW-DIMS1RF/-DIMS4RF, &
CLS-SLVD1RF Specifications (continued)
SPECIFICATION DETAILS
Operating Temperature
and Humidity
Dimensions and Weight -DIM1RF/-DIM4RF and
1. The range is dependent on its placement and the building in which
it is used. The construction of the building, obstructions, and RF
interference from other devices are factors determining the
effective range of the unit.
2. The latest software versions can be obtained from the Crestron
website. Refer to the NOTE following these footnotes.
3. Crestron 2-Series control systems include the AV2 and PRO2.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
4. Refer to Derating Charts for Multigang Installations on page 4.
5. VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
-DIMS1RF/-DIMS4RF:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.88 in (4.77 cm)
Weight: 4.9 oz (0.67 kg)
-SLVD1RF:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.88 in (4.77 cm)
Weight: 3.6 oz (0.50 kg)
NOTE: Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
CLW-DIM1RF/-DIMS1RF (L) and CLW-SLVD1RF (R)
shown in white
CLW-DIM4RF/-DIMS4RF shown in white
Physical view of CLW-DIM1RF/-DIMS1RF
(clockwise from top; Top, Side, and Front)
1.75 in
(4.45 cm)
Physical Description
The -DIM1RF and -DIMS1RF contain one rocker button,
a light emitting diode (LED) with software-adjustable
brightness, and a three-position slider-switch, shown in
the next column.
The -DIM4RF and -DIMS4RF contain four pushbuttons,
a light emitting diode (LED) with software-adjustable
brightness, and a three-position slider-switch, shown in
the next column.
The -SLVD1RF is similar to the -DIM1RF and
-DIMS1RF but does not have the slider-switch. The
brightness of the LED on the -SLVD1RF is not
programmable.
Line voltage connections are made at the rear of the
dimmer.
2 • infiNET™ Wall Box Dimmer : CLW-DIM1/4RF, DIMS1/4RF, & SLVD1RF Installation Guide – DOC. 6292A
2.38 in
(6.03 cm)
RUN SET OFF
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
(10.48 cm)
4.13 in
1.88 in
(4.77 cm)
1.50 in
(3.81 cm)
2.70 in
(6.86 cm)

Physical view of CLW-DIM4RF/-DIMS4RF
(clockwise from top; Top, Side, and Front)
1.75 in
(4.45 cm)
infiNET™ DIMMERS
FCC ID: EROCWD1011
Compliance Statement (Part 15.19 )
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2.38 in
(6.03 cm)
RUN SET OFF
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
(10.48 cm)
4.13 in
1.88 in
(4.77 cm)
1.50 in
(3.81 cm)
2.70 in
(6.86 cm)
Physical view of CLW-SLVD1RF (clockwise from top; Top,
Side, and Front)
1.75 in
(4.45 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.88 in
(4.77 cm)
2.70 in
(6.86 cm)
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
RF Exposure (OET Bulletin 65)
To comply with FCC's RF exposure limits for general
population / uncontrolled exposure, this transmitter must
be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or
transmitter.
Industry Canada Statement
The term "IC" before the certification/registration number
only signifies that the Industry Canada technical
specifications were met.
IC: 5683A-CWD1011
Important Notes
Read before installation.
• Codes: Install in accordance with all local and
national electrical codes.
CAUTION: TO REDUCE THE RISK OF
•
OVERHEATING AND POSSIBLE DAMAGE
TO OTHER EQUIPMENT, DO NOT INSTALL
TO CONTROL A RECEPTACLE OR A
MOTOR OPERATED APPLIANCE (i.e. BATH
FAN).
• Wiring: Use copper wire only. For supply
1.50 in
(3.81 cm)
These devices mount in a standard wallbox and are
covered using a decorative faceplate (not included).
connections, use wires rated for at least 75°C.
• Lamp Type: The -DIM1RF, -DIM4RF,
-DIMS1RF, -DIMS4RF, and -SLVD1RF are
designed for use with permanently installed
incandescent, magnetic low voltage, or tungsten-
Industry Compliance
This product is Listed to applicable UL Standards and
requirements by Underwriters Laboratories Inc.
halogen only.
• Temperature: The -DIM1RF, -DIM4RF,
-DIMS1RF, -DIMS4RF, and -SLVD1RF are
designed for use where temperatures are between
32° to 104°F (0° to 40°C).
E239011
Installation Guide – DOC. 6292A infiNET™ Wall Box Dimmer: CLW-DIM1/4RF, DIMS1/4RF, & SLVD1RF • 3