CLW-SW1, SWS1, & SLVS1(W/A/B)
Introduction
Features and Functions
The CLW-SW1 (-SW1) is a stand-alone wall box switch
that can also act as a Cresnet
Crestron® control processor. The -SW1 includes two
isolated, non-polarized Cresnet wires (plus a ground wire)
for connecting to a Cresnet system over a twisted pair
wire with shield.
The CLW-SW1 features a three-position mode selection
switch. Refer to “Operation ” on page 5 for more
information. In the absence of Cresnet communications,
the switch can still be used to control a load.
The CLW-SWS1 (-SWS1) is similar to the -SW1 with the
added capability of working with a slave unit
(CLW-SLVS1) in a multi-switch / single circuit
application.
The CLW-SLVS1 (-SLVS1) is a slave unit that when
used in conjunction with the -SWS1 acts as an additional
switch control point in a multi-switch / single circuit
application. It does not connect to a Cresnet system and
cannot be used without a -SWS1. The -SLVS1 does not
have a mode selection switch and is not programmable. It
emulates the operation of the -SWS1 to which it is
connected unless the mode selection switch of the master
is set to “OFF”.
These switches are available in white, almond, and black.
White units are designated by part numbers ending in
“W”. Almond units are designated by part numbers
ending in “A”. Black units are designated by part numbers
ending in “B”. Each switch can be covered with a
decorative faceplate (not supplied).
Specifications
Following are specifications for the -SW1, -SWS1, and
-SLVS1.
CLW-SW1, CLW-SWS1, & CLS-SLVS1 Specifications
SPECIFICATION DETAILS
Power Requirements Line Power, 120 VAC, 60 Hz
Default Net ID SW1: 82
Switch Type Single-Pole, Single-Throw
Load Type Incandescent, Tungsten Halogen,
®
device that reports to a
SWS1: 83
Fluorescent / High Intensity
Discharge (HID), Electronic Low
Voltage, Magnetic Low Voltage, Neon
/ Cold Cathode, General Purpose Fan
CLW-SW1, CLW-SWS1, & CLS-SLVS1 Specifications
(Continued)
SPECIFICATION DETAILS
2-Series Control System
Update File
Load Ratings3
Incandescent / Tungsten
Halogen
Magnetic Low Voltage4 -SW1: 1000VA/750W
Neon / Cold Cathode4 -SW1: 1000VA/750W
Electronic Low Voltage -SW1: 1000W
Fluorescent / High
Intensity Discharge
(HID)
General Purpose Fan -SW1: 3.0A
Minimum Load 40W / 0.5A
Operating Temperature
and Humidity
Dimensions and Weight -SW1 and -SWS1:
1. The latest software versions can be obtained from the Crestron
2. Crestron 2-Series control systems include the AV2 and PRO2.
3. Refer to Derating Charts for Multigang Installations on page 3.
4. VA ratings are for input power to the transformer. If you do not
1,2
website. Refer to the NOTE following these footnotes.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
Version 3.117 or later
-SW1: 1000W
-SWS1: 1000W
-SLVS1: N/A
-SWS1: 1000VA/750W
-SLVS1: N/A
-SWS1: 1000VA/750W
-SLVS1: N/A
-SWS1: 1000W
-SLVS1: N/A
-SW1: 8A
-SWS1: 8A
-SLVS1: N/A
-SWS1: 3.0A
-SLVS1: N/A
32°F to 104°F (0°C to 40°C )
10 to 90% Relative Humidity
(Non-Condensing)
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.91 in (4.85 cm)
Weight: 4.4 oz (0.61 kg)
-SLVS1:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.91 in (4.85 cm)
Weight: 3.6 oz (0.50 kg)
NOTE: Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
(Continued on next column)
Crestron Electronics, Inc. Installation Guide – DOC. 6251A
15 Volvo Drive Rockleigh, NJ 07647 2009753
Tel: 888.CRESTRON 07.06
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
CLW-SW1, SWS1, & SLVS1(W/A/B)
)
Physical Description
The -SW1 and -SWS1 contain one large pushbutton, a
light emitting diode (LED) with software adjustable
brightness*, and a three-position slider-switch, shown
after this paragraph. Line voltage connections are made at
the rear of the switch. Three Class 2 low voltage wires,
located on the front of the switch, provide a Cresnet
connection to a control system. The wires can be routed to
the bottom of the unit for placement outside of the wall
box. The -SLVS1 is similar to the -SW1 and -SWS1 but
does not have the slider-switch or the Class 2 low voltage
wires.
* LED brightness can only be adjusted through Crestron programming
software.
CLW-SW1/SWS1 (L) and CLW-SLVS1 (R) shown in white
Physical view of CLW-SW1/SWS1 (clockwise from top; Top,
Side, and Front)
1.75 in
(4.45 cm)
Physical view of CLW-SLVS1 (clockwise from top; Top, Side,
and Front)
1.75 in
(4.45 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.91 in
(4.85 cm)
2.70 in
(6.86 cm
1.50 in
(3.81 cm)
The -SW1, -SWS1, and -SLVS1 mount in a standard
wallbox and are covered using a decorative faceplate (not
included).
Industry Compliance
This product is Listed to applicable UL Standards and
requirements by Underwriters Laboratories Inc.
2.38 in
(6.03 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
(10.48 cm)
4.13 in
1.91 in
(4.85 cm)
1.50 in
(3.81 cm)
2.70 in
(6.86 cm)
E239013
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
CAUTION: Changes or modifications not expressly
approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning
2 • Stand Alone Wall Box Switch: CLW-SW1, SWS1, & SLVS1 Installation Guide – DOC. 6251A
CLW-SW1, SWS1, & SLVS1(W/A/B)
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Important Notes
Read before installation.
• Codes: Install in accordance with all local and
national electrical codes.
Alternate wiring methods may be used for the
Class 2 wiring connection. The 2002 National
Electrical Code (Article 725-55) prohibits Class
2 conductors of the -SW1, -SWS1, and -SLVS1
to occupy the same outlet box as the power
conductors. The exception is Part D of Section
725.55 of the 2002 National Electrical Code,
which allows a device’s power conductors to be
installed near (0.25 inch minimum spacing)
associated Class 2 conductors in the same outlet
box. Consult the 2002 National Electrical Code
Handbook and your local electrical inspector
before proceeding.
Do not use the supplied butt-splice connectors if
the Class 2 conductors are to be installed in the
wallbox with the power conductors. Use
approved connectors (supplied by others) to
make Class 2 connections inside the wallbox.
recommends using 3 ½” deep wallboxes. Several
devices can be installed in one wall box
(multigang). This requires the removal of side
sections (shown below) and the derating of the
switching device. For a smooth appearance, onepiece multigang faceplates (not supplied) can be
installed.
• Other Switch Devices: Mechanical 3- or 4-way
switches will not work with the -SW1, -SWS1,
or -SLVS1.
• Spacing: If mounting one device above another,
leave at least 4 ½” vertical space between them.
Multigang Installations
In multigang installations, several controls are grouped
horizontally in one wallbox. For a smooth appearance,
one-piece multigang faceplates (not supplied) can be
installed.
1. When combining controls in a wallbox, remove
inner side sections prior to wiring (refer to the
following figure).
Inner Sections of Multiganged Switches
REMOVE INNER SECTIONS
CAUTION: TO REDUCE THE RISK OF
•
OVERHEATING AND POSSIBLE DAMAGE
TO OTHER EQUIPMENT, DO NOT INSTALL
TO CONTROL A RECEPTACLE.
• Wiring: Use copper wire only. For supply
connection, use wires rated for at least 75°C.
• Load Type: The -SW1, -SWS1, and -SLVS1 are
designed for use with permanently installed
incandescent, fluorescent (non-dimmable), low
voltage, neon/cold cathode, HID, general
purpose fan, or tungsten halogen lighting.
• Temperature: The -SW1, -SWS1, and -SLVS1
are designed to be used where temperatures are
between 32° to 104°F (0° to 40°C).
• Wallboxes: Devices mount in standard
The load capacity must also be derated. The
following charts provide derating information for
various applications.
Derating Information for Incandescent, Tungsten Halogen,
and Electronic Low Voltage Applications
Part Number No Side
-SW1 1000W 600W 400W
-SWS1 1000W 600W 400W
-SLVS1 No Derating Necessary
DO NOT REMOVE OUTER SECTIONS
Removed
One Side
Removed
Two Sides
Removed
wallboxes. For easy installation, Crestron
Installation Guide – DOC. 6251A Stand Alone Wall Box Dimmer: CLW-SW1, SWS1, & SLVS1 • 3
CLW-SW1, SWS1, & SLVS1(W/A/B)
Derating Information for Magnetic Low Voltage and
Neon/Cold Cathode Applications
Part
Number
-SW1
-SWS1
-SLVS1
* VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the bulb’s
wattage rating to determine proper rating.
Derating Information for Fluorescent/HID Applications
Part
Number
-SW1
-SWS1
-SLVS1
Derating Information for General Purpose Fans
Part
Number
-SW1
-SWS1
-SLVS1
No Side
Removed
1000VA/750W 600VA/450W 400VA/300W
1000VA/750W 600VA/450W 400VA/300W
No Side
Removed
8A 5A 3A
8A 5A 3A
No Side
Removed
3A 3A 3A
3A 3A 3A
*
One Side
Removed
No Derating Necessary
One Side
Removed
No Derating Necessary
One Side
Removed
No Derating Necessary
Two Sides
Removed
Two Sides
Removed
Two Sides
Removed
2. To remove a side section, bend the side section
back and forth with a pair of pliers until the
section breaks off from the mounting plate. Use a
file or sandpaper to remove any excess metal.
Prewire for Master Application
Each device has two Class 2 low voltage wires (plus a
ground wire) that provide a Cresnet connection over
shielded twisted-pair to a Crestron control system. These
wires are routed to the bottom of the device for
connection outside of the wallbox. The low voltage wires
are pulled from each device location to the Crestron
control system or a Crestron connection block device. Use
#22 AWG, twisted, shielded, 2-conductor wire. Wiring
can be daisy chained, T-tapped, or home run back to the
control system. Refer to the following wiring diagram.
NOTE: The GRAY (Cresnet) wires are not polarized.
These wires can be connected to either the Y or Z line on
a Cresnet port.
NOTE: The BLACK wire (Cresnet ground) should not
be grounded with the GREEN (Ground) wire on the
-SW1/-SWS1.
NOTE: Crestron recommends using Cresnet-DM cable
for connecting the -SW1 and -SWS1 to the Cresnet
network.
Installation
WARNING: Turn off power at the circuit breaker.
Installing with power on can result in serious personal
injury and damage to the device.
NOTE: The -SW1, -SWS1 require a neutral wire for
operation. If no neutral is present, contact a licensed
electrician for installation, otherwise the device will not
work.
NOTE: The -SWS1 must be installed in the same
wallbox that contains the connections to the load.
NOTE: New installations should be checked for short
circuits prior to installing the -SW1, -SWS1, or -SLVS1.
With power off, close the circuit and restore power. If the
load does not work or a breaker trips, check and correct
the wiring or fixture (if necessary). Install the -SW1,
-SWS1, or -SLVS1 only when the short is no longer
present. The warranty is void if the -SW1, -SWS1, or
-SLVS1 is installed and operated with a shorted load.
When installing a -SW1 or a -SWS1 without a slave,
follow the instructions in “Wiring a -SW(S)1 (No
Slaves)” below. If wiring a -SWS1 with a -SLVS1, refer
to “Wiring a -SWS1 with One or More
-SLVS1s” on the next page.
Wiring Diagram of CLW device to Cresnet
Wiring a -SW(S)1 (No Slaves)
The following describes the installation of a stand-alone
-SW1 or -SWS1.
1. Turn power off at the circuit breaker.
2. Pull Class 2 low voltage wires through a hole in
the drywall located outside of the electrical box,
to the Crestron control system or a Crestron
connection block device. Leave wires outside of
the wallbox for connection to the -SW1 or
-SWS1.
NOTE: Alternate wiring methods may be used
for the Class 2 wiring connection. Refer to
4 • Stand Alone Wall Box Switch: CLW-SW1, SWS1, & SLVS1 Installation Guide – DOC. 6251A
CLW-SW1, SWS1, & SLVS1(W/A/B)
section 725-55, Part D of the 2002 National
Electric Code.
3. Wire the switch as shown in Figure 1 on
page 8.
NOTE: The RED (Load) and BLACK (Hot)
wires are #14 AWG. The BLUE (Slave) and
WHITE (Neutral) wires are #18 AWG. The
GREEN (Ground) wire is #16 AWG. The GRAY
(Cresnet) wires are #22 AWG. The BLACK wire
(Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
NOTE: Since the -SWS1 is installed without a
-SLVS1, the BLUE lead (Slave) should be
capped.
Other Wiring
For another scenario that may be encountered
during installation, refer to Figure 2 on page 8.
4. Splice the gray wires of the -SW1 or -SWS1 to
the Class 2 low voltage wires connected to the
Crestron control system or a Crestron connection
block device. Push the wires and the splices into
a hole in the drywall to provide the necessary
separation.
5. Push all power wires back into the wallbox and
fasten the device to the wallbox with the
provided screws.
6. Attach decorative faceplate.
7. Restore power at the circuit breaker.
Wiring a -SWS1 with One or More
-SLVS1s
NOTE: The -SWS1 must be installed in the same
wallbox that contains the connections to the load.
The following describes installation of a -SWS1 master
with a -SLVS1 slave.
1. Turn power off at the circuit breaker.
2. Pull Class 2 low voltage wires through a hole in
the drywall located outside of the electrical box,
to the Crestron control system or a Crestron
connection block device. Leave wires outside of
the wallbox for connection to the -SW1 or
-SWS1.
3. Wire the switches as shown in Figure 3 on
page 8.
NOTE: Do not connect the BLUE (Slave) wire
to the Black (Hot) or RED (Load) wires.
NOTE: The RED (Load) and BLACK (Hot)
wires are #14 AWG. The BLUE (Slave) and
WHITE (Neutral) wires are #18 AWG. The
GREEN (Ground) wire is #16 AWG. The GRAY
(Cresnet) wires are #22 AWG. The BLACK wire
(Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
NOTE: If a -SWS1 is installed without a
-SLVS1, the BLUE lead (Slave) should be
capped.
NOTE: The WHITE (Neutral) connection on
the -SLVS1 is optional and is only required for
operation of the LED. If the neutral is not
available, the white lead should be capped off.
4. Splice the gray wires of the -SWS1 to the Class 2
low voltage wires connected to the Crestron
control system or a Crestron connection block
device. Push the wires and the splices into a hole
in the drywall to provide the necessary
separation.
5. Push all power wires back into the wallbox and
fasten the devices to their respective wallboxes
with the provided screws.
6. Attach decorative faceplates.
7. Restore power at the circuit breaker.
Operation
The -SW1, -SWS1, and -SLVS1 have one large
pushbutton. The -SW1 and -SWS1 also have a threeposition mode selection switch. The function of the
pushbutton is determined by the position of the mode
selection switch. Refer to the following diagram.
NOTE: The -SLVS1 does not have a mode selection
switch. It emulates the operation of the -SWS1 to which it
is connected unless the mode selection switch of the
master is set to “OFF”.
NOTE: Alternate wiring methods may be used
for the Class 2 wiring connection. Refer to
section 725-55, Part D of the 2002 National
Electric Code.
Installation Guide – DOC. 6251A Stand Alone Wall Box Dimmer: CLW-SW1, SWS1, & SLVS1 • 5
CLW-SW1, SWS1, & SLVS1(W/A/B)
h
Buttons of CLW-SW1, -SWS1, and -SLVS1
Setup & Programming
Required Software
Button
Mode Selection Switc
(-SW1 & -SWS1 Only)
OFF
When the mode selection switch is in the “OFF” position,
the pushbutton will not have any function and the load is
disconnected from the power source. This must be used
when changing light bulbs to ensure that the load is fully
disconnected from power.
ADJ
When the switch is in the ADJ position, pressing and
holding the pushbutton will set a delay time for
deactivating the load when the switch is in the PRE
position. To set the delay time, press and hold the
pushbutton for the desired amount of time delay and
release. When the pushbutton is released, the LED will
flash three times to confirm the time delay setting. When
done, return the switch to the PRE position.
Software
TASK REQUIRED SOFTWARE VERSION
Program control
system to operate
CLW-SW1.
Upload program
and firmware.
Program with
simple wizards for
lighting systems
using a CLW-SW1
(optional but
recommended).
SIMPL™ Windows® version
2.07.32 or later with SIMPL+ Cross
Compiler version 1.1 or later and
Library update 387 or later; Also
requires Crestron Database
version 18.1.5 or later.
Crestron Toolbox 1.02.29 or later.
Crestron D3 Pro™ version 2.1.7 or
later with D3 Pro Templates
version 2.0.1 or later. Refer to
software release notes or Crestron
website for other required Crestron
software packages.
Setup
The Net ID of the CLW-SW1 has been factory set to 82.
The Net IDs of multiple CLW-SW1 devices in the same
system must be unique. Net IDs are changed from a
personal computer (PC) via the Crestron Toolbox. When
setting the Net ID, the Net ID of each unit must match an
ID code specified in the SIMPL Windows program.
For more details, refer to the Crestron Toolbox help file.
NOTE: If a time delay is not set, the delayed-off feature
is disabled by default.
PRE
When the switch is in the PRE position, the load can be
manually activated and deactivated with the pushbutton.
Pressing the pushbutton will deactivate the load after a
delay that was set when the switch was in the ADJ mode.
During the delay, the LED will flash. Tapping the
pushbutton during the delay will deactivate the load
without a delay.
NOTE: The device may be warm to the touch during
operation. This is normal.
D3 Pro
Crestron D3 Pro Software provides all the tools necessary
to create a complete Crestron Lighting System for
residential applications. The lighting system includes the
control system program, touchpanel screens and keypad
programming, documentation, and real-time lighting
adjustment capabilities. As with all Crestron software, the
D3 Pro software provides extensive right-click and dragand-drop functionality, in addition to convenient
keyboard shortcuts for frequently used functions and
commands.
For additional details, download D3 Pro from the
Crestron website and examine the extensive help file.
SIMPL Windows
SIMPL Windows is Crestron’s premier software for
programming Crestron control systems.
NOTE: While SIMPL Windows can be used to program
the CLW-SW1, it is recommended to use D3 Pro for
configuring a Crestron lighting system.
• In Configuration Manager, incorporate a CLW-SW1
into the system by dragging the CLW-SW1 from the
6 • Stand Alone Wall Box Switch: CLW-SW1, SWS1, & SLVS1 Installation Guide – DOC. 6251A
CLW-SW1, SWS1, & SLVS1(W/A/B)
Lighting | Wall Dimmers/Switches (Cresnet CLW
Series) folder of the Device Library and dropping it
in the System Views. Double click a device to open
the “Device Settings” window and change the Net ID
if required. The ID code specified in the SIMPL
Windows program must match the Net ID of each
unit.
• In Programming Manager, assign signal names to
program the CLW-SW1 to operate with the control
system.
For additional details, download SIMPL Windows from
the Crestron website and examine the extensive help file.
Installation Guide – DOC. 6251A Stand Alone Wall Box Dimmer: CLW-SW1, SWS1, & SLVS1 • 7
CLW-SW1, SWS1, & SLVS1(W/A/B)
Appendix: Wiring Diagrams
Following are wiring diagrams for circuits that may be found when installing a switch:
Stand-Alone Installations
Figure 1: Wiring a CLW-SW(S)1
To continue a circuit past a switched light fixture to one or more duplex receptacles, connect the switch as shown in the
following diagram.
Figure 2: Adding a Duplex Receptacle Past a Switched Light Fixture
Master-Slave Installation
Figure 3: Wiring a CLW-SW1 with a CLW-SLVS1
8 • Stand Alone Wall Box Dimmer: CLW-SW1, SWS1, & SLVS1 Installation Guide – DOC. 6251A
CLW-SW1, SWS1, & SLVS1(W/A/B)
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange, or service without prior authorization from
CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized
CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an
RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the
problem, name and phone number of contact person, RMA number, and return address.
2. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise
Authorization (RMA) number. Authorized returns must be shipped freight prepaid to
CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number
clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA
number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute
discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an
RMA.
3. Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials and
workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON,
with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and
power supplies are covered for a period of one (1) year; touchscreen display and overlay components are
covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended, or if it has been subjected to misuse, accidental damage,
modification, or improper installation procedures. Furthermore, this warranty does not cover any product that
has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall CRESTRON
be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising
from the sale or use of this equipment. CRESTRON is not liable for any claim made by a third party or made by
the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired
portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied,
nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or
fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of
this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of
Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft Corporation.
Installation Guide – DOC. 6251A Stand Alone Wall Box Switch: CLW-SW1, SWS1, & SLVS1 • 9
CLW-SW1, SWS1, & SLVS1(W/A/B)
This page is intentionally left blank.
10 • Stand Alone Wall Box Switch : CLW-SW1, SWS1, & SLVS1 Installation Guide – DOC. 6251A
Loading...