This document was prepared and written by the Technical Documentation department at:
Regulatory Compliance
Federal Communications Commission (FCC) Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Industry Canada (IC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
As of the date of manufacture, the QM -FBCC/WCC-1 has been tested and found to comply with specifications
for CE marking and standards per EMC and Radiocommunications Compliance Labelling.
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
Single cable signal transmission up to 450 feet (137 meters)
DB15HD RGB computer input
Stereo audio input
Video input signal sensing
QuickMedia transport
Cresnet® communications
Low-cost, quick and easy installation
Performs Video signal format management via EDID
Easy setup using Creston SystemBuilder™ software
QM-FBCC-1:
Floor box mountable QuickMedia computer interface
Fits Hubbell SystemOne floor boxes and poke-throughs
Compatible with Hubbell Style Line® and Leviton decorator
Crestron® MediaManager is a comprehensive family of affordable
products fusing high performance AV signal distribution, device control
and facility-wide system management. MediaManager simplifies the art
of Pro AV system design and installation with complete hardware,
software and low-cost wiring solutions. Whether installing a single
boardroom or a campus-wide network of AV systems, MediaManager
delivers power and value far beyond conventional products and designs.
Wall mount QuickMedia computer interface
Integrates with Crestron C2N-CBD and C2N-DB Series
Keypads
Installs alongside third-party LAN jacks and other devices
Available in white or black
Features and Functions
(Continued)
The QM-FBCC-1 QuickMedia® Floor Box Computer Center is designed
for mounting in a variety of popular floor boxes and the QM-WCC-1
QuickMedia Wall Plate Computer Center provides a simple wall mount
computer interface solution for any MediaManager system, including
applications ranging from small conference rooms to large banquet halls
and auditoriums.
For simplicity within this guide, the term “QM-FBCC/WCC-1” is used
except where noted.
Floor Box Computer Interface (QM-FBCC-1 only)
The QM-FBCC-1 installs cleanly in a Hubbell SystemOne floor box or
poke-through using their Style Line® Sub-plate and Universal Cover. Its
slim dimensions and standard screw spacing may also make it suitable
for use with a variety of other floor box systems. An adhesive insert is
included to fit Hubbell Style Line and Leviton decorator style faceplate
cutouts.
Each QM-FBCC-1 provides a single RGB input with stereo audio to
accept a connection from a computer or other RGB source. Built-in
signal sensing can be utilized to trigger automatic input selection and
power control. Wiring for the QM-FBCC-1 is extremely simple requiring
just a single CresCAT®QM cable (sold separately).
Wall Mount Computer Interface (QM-WCC-1 only)
The QM-WCC-1 installs cleanly in a standard electrical box using a
decorator style faceplate (not supplied). A single RGB input with stereo
audio is provided to accept a connection from a computer or other RGB
source.
Connectivity for LAN and other signals can easily be added by ganging
the QM-WCC-1 together with other third-party wall plate devices. A
Crestron C2N-CDB or C2N-DB series keypad may also be installed for a
truly complete interface and control solution. Wiring for the QM-WCC-1
is extremely simple, requiring just a single CresCAT-QM cable (sold
separately).
Built-in signal sensing can be utilized to trigger automatic input selection
and power control.
QuickMedia® Transport
Using the revolutionary Crestron QuickMedia (QM) transport, input
signals are transmitted from the QM-FBCC/WCC-1 to any QuickMedia
receiver or distribution center over a single inexpensive CAT5e type
cable. Computer resolutions up to 1920 x 1200 pixels at 60 Hz are
supported over cable runs up to 450 feet (137 meters). Audio signals are
transmitted digitally with high performance 24-bit resolution.
QuickMedia dramatically simplifies system design and installation,
affording a higher level of performance at a lower overall cost.
NOTE: For QuickMedia wiring use CresCAT-QM, CresCAT-IM or
quality CAT5e/CAT6 cable with a delay skew of ≤ 15 ns per 328 feet
(100 meters); the maximum aggregate cable length and delay skew
between any QM transmitter (origination point) and QM receiver
(endpoint) is 450 feet (137 meters) and 22 ns; a maximum of two QM
midpoint devices may be inserted in a given QM signal path; exceptions
apply, refer to each respective product manual for details.
MediaManager System Integration
Whether using just one floor box or wall plate computer center or
several, complete system operation can be made transparent to the end
user with all signal routing occurring smoothly under the command of the
MediaManager control system. Complete MediaManager systems are
easy to design, program and adjust from start to finish using Crestron
SystemBuilder™ software.
EDID Format Management
The QM-FBCC/WCC-1 allows for management of the EDID (Extended
Display Identification Data) information sent to the connected source.
Using Crestron Toolbox™ software, the format and resolution
capabilities of each device can be assessed and managed through the
QM-FBCC/WCC-1, ensuring reliable operation by instructing sources to
output only the resolutions and formats that can be handled by the
displays and system wiring.
Applications
The following diagram shows a QM-FBCC-1 and QM-WCC-1 in a
lecture hall application.
QM-FBCC-1 and QM-WCC-1 in a Lecture Hall Application
1920 x 1200 @ 60 Hz (at unity
gain) with maximum cable length
of 450 feet (137 meters) and
maximum compensation at
receiver
Audio
A-D Conversion
24-bit, 48 kHz
Frequency Response
20 Hz to 20 kHz
Power Requirements
Cresnet Power Usage
4 Watts
(0.17 Amps @ 24 Volts DC)
Default Net ID
8E
Minimum 2-Series
Control System Update
File
1, 2
Version 3.155.1240 or later
Environmental
Temperature
41º to 104º F (5º to 40º C)
Humidity
10% to 90% RH (non-condensing)
Heat Dissipation
14 BTU/Hr
For more information on this and other QM applications, refer to the
latest revision of the Crestron MediaManager Applications Guide
(Doc. 6244), which is available from the Crestron Web site
(www.crestron.com/manuals).
Specifications
Specifications for the QM-FBCC/WCC-1 are listed in the following
table.
Mountable on either side of a
Hubbell SystemOne floor box or
poke-through using Style Line®
Sub-plate (S1SP) and Universal
Cover or any floor box with a
standard wall plate screw spacing
(3.81 inch, 97 mm), 2.1 inch (54
mm) high x 0.8 inch (21 mm) wide
minimum faceplate cut-out and 2.1
inch (54 mm) minimum depth
behind faceplate;
Included insert accommodates
Hubbell Style Line and Leviton
decorator style faceplate cut-outs
QM-WCC-1
Flush Wall Mount
1-gang mountable in a standard
electrical box, 2.1 inch (54 mm)
deep minimum;
Requires decorator style faceplate
(not included)
QuickMedia Wall Plate Computer
Center, Single Input, Black
QM-WCC-1-W-T
QuickMedia Wall Plate Computer
Center, Single Input, White
Available Accessories
CresCAT-IM
iMedia Cable
CresCAT-QM
QuickMedia Cable
Cresnet
Cresnet Control Cable
QM-FBCC/WCC-1 Specifications (Continued)
1. The latest software versions can be obtained from the Crestron Web site. Refer to
the NOTE following these footnotes.
2. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest
Crestron Product Catalog for a complete list of 2-Series control systems.
NOTE: Crestron software and any files on the Web site are for
authorized Crestron dealers and Crestron Authorized Independent
Programmers (CAIP) only. New users may be required to register to
obtain access to certain areas of the site (including the FTP site).