Creston FSDI8-W QUICK GUIDE
FSDI8-W
1
Ceiling Mount Media Presentation Speakers
1
quickstart guide
Installation
1
Crestron® FSDI8-W speakers are 8-Ohm, full-range, drop-in ceiling speakers
that allow for fast and easy installation in a typical classroom or presentation
space.
Constructed of industrial grade steel, the speakers are fully enclosed, including
the back can, with a finely perforated grill over the entire front of the speaker.
The FSDI8-W fits perfectly into place in a 2’ X 2’ (0.61 m X 0.61 m) ceiling grid,
and can also be installed in a 2’ X 4’ (0.61 m X 1.22 m) grid by making a single
cut to the ceiling tile and installing the included support rail crossbar.
Installation consists of the following (refer to the illustration below):
1. Place the speaker into position in the grid. In a 2’ X 4’ grid, cut the ceiling tile
in half (23-3/4” max), and install the included support rail.
Speaker Connections
Support Rail
Crossbar Included
(For use in 2’ X 4’ tile space only)
Seismic Attachment
Points (4)
2. Route the speaker cable to the speaker.
3. Strip the ends of the speaker cable wire approximately 5/8 inch (15 mm)
and twist the bared strands.
4. Remove the screws securing the cover on the back can, open the cover
and remove the included wire nuts.
5. Following one of the two methods shown in the illustration, use the wire
nuts to connect the speaker wires to the speaker cable wires, observing
the proper polarity (+ to +, - to -).
6. Using the screws removed earlier, attach the cover to the back can.
Lead Color
Red
+
—— Black
Cable Clamp
(Not Included)
Knockout
Wire
Nuts
Speaker
Cable
Cover
Speaker
Leads
FSDI8-W
1
For Regulatory Compliance information, refer to the latest
version of Doc. 7071.
QUICKSTART DOC. 7070A (2028977) 10.10
www.crestron.com
©2010 Specifications subject to
change without notice.
Wire
Nuts
888.273.7876 201.767.3400
All brand names, product names, and trademarks
are the property of their respective owners.
Cover
Speaker
Cable
Speaker
Leads
FSDI8-W
Ceiling Mount Media Presentation Speakers
1111111111
Specifications
2
FSDI8-W Specifications
SPECIFICATION
Cone Material & Surround
Cones
Frequency Response 85 Hz to 20 kHz (-10 dB)
quickstart guide
Maximum Power
Dispersion @ 2 kHz (6 dB down)
Dimensions
Height
Width
Depth
3
DETAILS
Treated Paper
8“ (203 mm) main cone with
secondary high frequency cone
)g 482( zo 01thgieW tengaM
94 dBSPL @ 1W / 1m
15 Watts @ 8-Ohm
100°
and 4 seismic attachment points
5 in (320 mm)
23-13/16 in (605 mm)
23-13/16 in (605 mm)
12 lbs (5.4 kg)Weight
3
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble
situations. If further assistance is required, please contact a Crestron
customer service representative.
TROUBLE POSSIBLE CAUSE(S)
No sound or
intermittent
sound from
speakers.
llirg detarofrep htiw leets edarg lairtsudnIerusolcnE
Constant noise
such as buzz,
hum or hiss
from speakers.
Poor low
frequency
output.
Cable connection error. Verify cable connections
Amplifier not receiving
input signal or amplifier
malfunction.
Faulty device in system. Verify all devices in system
System grounding fault. Verify system grounding.
Incorrect polarity
connection at speaker.
CORRECTIVE ACTION
between amplifier and
speakers.
Verify amplifer is functioning
correctly, that it is receiving
an input signal and that
correct input source is
selected.
are functioning properly.
Verify speaker connection
polarity (i.e. + on speaker to
+ on amplifier).
2
For Regulatory Compliance information, refer to the latest
version of Doc. 7071.
QUICKSTART DOC. 7070A (2028977) 10.10
www.crestron.com
©2010 Specifications subject to
change without notice.
Further Inquiries
If you cannot locate specific information or have questions after
reviewing this guide, please take advantage of Crestron's award
winning customer service team by calling Crestron at
1-888-CRESTRON [1-888-273-7876].
You can also log onto the online help section of the Crestron Web site
(www.crestron.com/onlinehelp) to ask questions about Crestron
products. First-time users will need to establish a user account to fully
benefit from all available features.
Future Updates
Check the Crestron Web site periodically for manual update availability
and its relevance. Updates are identified as an “Addendum” in the
Download column.
888.273.7876 201.767.3400
All brand names, product names, and trademarks
are the property of their respective owners.
FSDI8-W
Loading...