Crest audio NC-MEQ DATASHEET
Power
Processing
INPUT PROCESSING MODULE
Modules
FOR CKS, CKV & CKX SERIES
POWER PROCESSING AMPLIFIERS
NC-MEQ 4-band Parametric EQ & Mono Crossover
Product Information
The NC-MEQ Module fits in the Input Processing bay located on the
rear panel of Crest Audio CKS, CKV & CKX Series Power Processing
amplifiers. It is an extremely high quality, fourth-order, two-way electronic mono crossover that includes a four-band fully programmable
parametric equalizer. The HF output is fed to channel A of the amplifier
and the LF output to channel B. The HF and LF crossover frequencies as
well as their individual output levels are individually programmable.
Each band of the equalizer has programmable boost/cut, bandwidth and
frequency parameters.
Features:
• NexSys compatible, programmable two-way, 24dB per octave electronic crossover
• Four-band parametric EQ with programmable boost/cut, bandwidth and frequency parameters
• All parameters (including precision attenuation settings) programmable via NexSys , hand-held N-Coder or N-Coder/PC software
• Independent two-way, 4th-order, Linkwitz-Riley filters • Post-EQ, loop-thru HF and LF outputs
• Balanced input on barrier strip connector • Removable gain pot knobs for security
Internal Features:
• Jumper-selectable gain of X20 (26 dB), X40 (32 dB, factory setting), or constant sensitivity for full output at 0dBu (.775V) in.
• Jumper-selectable assignment of high-pass or low-pass output for each amplifier channel
Unbalanced post-EQ loop-thru barrier strip connectors provide convenient outputs to other amplifiers. An internal jumper selects between
gains of X20 (26 dB), X40 (32 dB), or constant sensitivity for full output
at 0dBu (.775V) in. The standard factory setting is for X40 (32dB).
Individual channel attenuators are provided with removable knobs for
extra security. The NC-MEQ is programmable via NexSys
held N-Coder or N-Coder/PC software. (NexSys-compatible
Power/Output and Network NC modules are required for NexSys implementation.)
®
, the hand-
NC-MEQ connections
PC Lap-Top running
N-Coder/PC software
CLASS 2
WIRING MAY
BE USED
Output
–
A
+
+
B
–
Signal
Ground
Lift
Jumper
Architects and Engineers Specifications - NC-MEQ.
The module shall plug into Crest Audio CKS or CKV Power Processing amplifiers in the
Input Processing bay. The module shall be NexSys-compatible. The module shall provide a
two-way, 24 dB per octave electronic crossover with programmable HF and LF output levels, HF and LF crossover frequencies, overall output level and HF/LF polarity inversion.
The module shall include a fully programmable four band parametric equalizer with center
frequency, bandwidth and boost/cut parameters. The module shall be controlled/programmed either by NexSys via an NC-NXS module (if fitted), a hand-held N-Coder or NCoder/PC software.
Designed & manufactured in the USA by:
Output Power
Model
@70.7V
Name
50W
CKV 100
100W
CKV 200
200W
CKV 400
400W
CKV 800
800W
CKV 1600
1200W
CKV 2400
Network
+–
+–
NexSys Bus
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
Model
Output Power
Name
CKS 100
CKS 200
CKS 400
CKS 800
CKS 800-2
CKS 1200-2
CKS 1600-2
Data
1
2
3
4
5
6
7
Hi
@8Ω/Ch.
50W
100W
200W
400W
400W
600W
800W
Address
F
E
D
C
B
A
9
8
Model
NC-NXS
F
1
E
2
D
3
C
4
B
5
A
6
9
7
8
Lo
N-Coder
Crest Audio
Revision 1.03E
OR
To other amplifiers
Daisy Chain Output
HP
N-Coder
Data
Port
All programmed settings shall be stored in non-volatile EEPROM memory. A barrier strip
input connector shall feed one electronically balanced input. Two removable-knob gain pots
shall be provided that control the level of each amplifier channel independent of programming. Post high pass and low pass loop-thru outputs shall be available on barrier strip connectors. An internal input sensitivity/voltage gain jumper shall be provided with selections
of 0dBu, X20 and X40. The module shall be designated the Crest Audio model NC-MEQ.
Input
–
+
Input
Signal
LP
Level
Level
Model
NC-MEQ
5
4
6
A
3
7
2
8
1
9
0
10
5
4
6
B
3
7
2
8
1
9
0
10
NC-MEQ Input Processing Module
Mono Crossover & 4-band Parametric EQ
Daisy
Chain
IN
+
-
G
HF
Out
LF
Out
LO EQ LO MID EQ HI MID EQ HI EQ
Data
Port
B/C F BW
HP 1
Freq
LP 1 LP 2
Freq Freq
B/C F BW
N-Coder
BLOCK
DIAGRAM
SPECIFICATIONS
Crossover frequencies: 80Hz-8kHz
Input impedance: 50kΩ
Dynamic Range: (about 112 dB) TBD
B/C F BW
HP 2
Freq
B/C F BW
Trim
Trim
Atten
Atten
I/F
ckt
ID
ckt
Vosc
Input for LM
Gain
Gain
NexSys
Module Bus
CH A
Power
Amp
CH B
Power
Amp
CONTROL OPTIONS
The following NC-MEQ parameters can be controlled by the hand-held N-Coder, N-Coder/PC
software, or via NexSys software.
Common mode rejection: >90dB typ.
Frequency response: (20Hz-20kHz, ±0.3dB) TBD
Programmable gain range: 0 to -83dB
Voltage gain/input sensitivity: X20 (26 dB),
X40 (32 dB),
or constant sens. for full output at 0dBu (.775V) in
Connectors: Balanced inputs and
unbalanced HP /LP daisy-chain outputs
on barrier strip connectors
with 0.325" (8.3mm) screw center
and 0.270" (6.9mm) lug space,
RJ-14 (‘RJ-11 6-pin’) N-Coder data port
Controls: 2 gain attenuators (w/removable knobs)
Crest Audio reserves the right to make improvements in manufacturing or design which may affect specification. Crest Audio specification literature is available in electronic form to qualified users.
v. 2.1 4/7/97
Contact Crest Audio Inc. for more information. NexSys is a registered trademark of Crest Audio Inc. ©1996 Crest Audio Inc.
*A3300027*
N-Coder:
Channel attenuation, phase reverse; boost/cut, frequency and bandwith control (four-band parametric
EQ).
N-Coder/PC software:
Channel attenuation, phase reverse, muting;
boost/cut, frequency and bandwith control (fourband parametric EQ).
NexSys computer control:
Channel attenuation, phase reverse, solo, muting,
input and output VU metering; boost/cut, frequency
and bandwith control (four-band parametric EQ).
Crest Audio Inc.
100 Eisenhower Dr., Paramus NJ 07652 USA
TEL: 201.909.8700 FAX: 201.909.8744
http://www.crestaudio.com
Printed in USA
Loading...