Crest Audio MFP3FM User Manual

SAFETY FIRST

1. Installation of this TV Wall Mount will be easier with two people.

2. Some images in this guide may vary slightly from the actual
components supplied.

3. Ensure this instruction manual is completely read and
understood before attempting installation.

4. This TV Wall Mount MUST NOT be installed solely in
plasterboard, fibre cement and similar surfaces.

5. This TV Wall Mount MUST be installed in sound supporting
structures such as those made of timber, steel or masonry
using appropriate fasteners.

6. The supporting structure must be capable of sustaining
the combined weight of the TV Wall Mount and the display
otherwise the structure must be reinforced.

7. The fasteners supplied in this hardware pack allow for fixing
into timber and masonry only. If installing into a supporting
structure made of steel, appropriate fasteners must be used
and sourced from an appropriate supplier.

8. Use appropriate tools and safety equipment and ensure
adequate ventilation during installation.

9. If uncertain about any aspect of installation, contact
The Crest Company or an installation professional.

Please retain these instructions for future reference.

Hardware Kit Contents

ITEM DESCRIPTION QTY ITEM DESCRIPTION QTY

M-A M5 x 14mm Bolt 4

W-A Lag Bolt ST6.3 x 55mm 6

M-B M6 x 14mm Bolt 4

W-B Concrete Anchor 6

M-C M8 x 20mm Bolt 4

W-C D6 Washer 6

M-D M6 x 30mm Bolt 4 A Wall Mount 1

M-E M8 x 30mm Bolt 4

M-F Washer 4 B Mounting Arm 2

M-G Small Spacer 8 C Stud Finder with Spirit Level 1

M-H Large Spacer 4

Tools Required

DRYWALL INSTALLATION (TIMBER SUPPORTS):

• Adjustable spanner/socket set

• Philips head screwdriver

• Power drill

• High speed 4.5mm drill bit

• Pencil

MASONRY INSTALLATION:

• Adjustable spanner/socket set

• Philips head screwdriver

• Power drill with hammer function

• 10mm masonry drill bit

• Pencil

• Hammer

MFP3FM

TV Wall Mount

Compatible TV Size

This TV Wall Mount fits 37-70”
(94-178cm) TV Screens

37-70”

Maximum TV Weight

This TV Wall Mount supports TVs
weighing up to 60kg

HOLDS

60

kg

Maximum Mounting Pattern

This TV Wall Mount has a mounting
hole pattern up to 400x800mm (HxW)

400x800mm

Full Motion

This TV Wall Mount allows you to move
your TV at all angles and extends out
up to 39cm from your wall

10.

Step 1: Attach Wall Plate to Wall

A. INSTALLING IN DRYWALL (TIMBER FRAME)

WARNING: If attaching this TV Wall Mount using this method, you MUST spread the wall plate across 2 wall studs.
Wall studs can be 450mm or 600mm apart depending upon the position of the wall and the geographical state
you live in. The Crest Company will not accept any damages that may occur if only 1 stud is used.
The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.

1. Locate the centre of 2 adjacent timber studs using the supplied stud finder with spirit level.
(NOTE: You must use the centre of the stud to avoid cracking or splitting the timber during installation).

2. Mark a minimum of 4 fixing holes over stud centres using the wall plate as a guide - position 2 at either end of the wall
plate (see Figure 1). Ensure plate is level.

3. Pre-drill holes to a minimum depth of 50mm using a high speed 4.5mm drill bit. If installing in hardwood, larger diameter
and deeper holes may be required.

4. Attach the wall plate using the lag bolts (W-A) through the washers (W-C). Do not over tighten.

B. INSTALLING IN MASONRY

WARNING: Ensure you have a minimum of 35mm of actual concrete/brick thickness in the hole for the anchors.
Do not drill into mortar joints. Installer must verify that the supporting surface will safely support the combined weight of
the TV Wall Mount and TV. The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.

1. Mark a minimum of four fixing holes (preferably 6) using wall plate as a guide - position 2 at either end of the wall plate (see
Figure 2). Ensure plate is level.

2. Pre-drill holes to a minimum depth of 60mm using 10mm masonry drill bit. Clean out holes.

3. Fully insert concrete anchors (W-B). Tap in with hammer if required.

4. Attach wall plate by inserting the lag bolts (W-A) through the washers (W-C) into each concrete anchor (W-B)
(see Figure 2). Do not over tighten.

Using the Stud Finder with Spirit Level

HOW IT WORKS:

• Use this stud finder on drywall (timber supports) only

• The stud finder accurately locates metal pipes, AC wires,

studs and wooden frames

• The stud finder LED indicator flashes GREEN when an
object is detected

• The stud finder can detect the depth of:

WOOD: up to 20mm, wood should be detected based

on the thickness of the drywall less than 20mm

METAL: up to 50mm, metal should be detected based

on the thickness of the drywall less than 50mm

VOLTAGE: up to 70mm, AC wires should be detected

based on the thickness of drywall less than 70mm

INSTRUCTIONS:

1. Keep the stud finder in touch with the drywall.

2. Press the ON/OFF button until the LED indicator turns
RED. Do not move the stud finder.

3. Wait 3 to 10 seconds until the LED indicator turns GREEN,
then start moving the stud finder on the drywall.

4. The GREEN LED indicator will start flashing when an

object is detected.

5. Mark a point on the wall using your pencil, then continue
moving the stud finder until the GREEN LED indicator
stops flashing, mark another point on your wall.

6. The midpoint between the two marks on your wall
is the centre of the stud.

Use the supplied stud finder

with spirit level to level
your TV Wall Mount
before installation

Find the wood stud, metal or
voltage before TV Wall Mount
installation

STUD