Crest audio HD2 SPECIFICATIONS
POWER AMPLIFIER
HD2
Product Description
The Crest Audio HD2 professional power amplifier is designed
to achieve unsurpassed sonic performance and long-term reliability–even when operating under extreme stress–in touring or fixed
installation applications.
Absolute sonic accuracy is the hallmark of every Crest amplifier.
Bass is solid and defined to the limits of audibility, with ample
current reserves delivered by an “over-engineered” power supply
and advanced Class AB output circuit design. Wide-bandwidth
output devices assure detailed, transparent high frequency
response.
Construction and Quality Control
The HD2 is built exclusively in Crest’s own USA manufacturing
facility, with internal components selected for premium quality
and proven durability. Each modular subassembly is pre-tested,
and the assembled HD2 receives a rigorous “hot room” burn-in
before thorough final checkout on precision test equipment.
Power Specifications:
Other HD Series Power Amplifiers
4Ω Stereo HD4 HD6 HD9 HD12 HD18
1kHz, .01% THD+N 435W 600W 900W 1200W 1800W
20Hz-20kHz, 0.1% THD+N 400W 500W 800W 1100W 1700W
HD2 Features
• Crest’s legendary “overbuilt” power supply
• Toroidal power transformer
• Latest generation of high-speed, wide-bandwidth output
devices
• Twin Tunnel Cooling with back-to-front air flow
• Dual, variable speed DC fans
• Massive, extruded aluminum heat sinks
• Balanced XLR and 1/4-inch (TRS) inputs
• 5-Way binding post outputs
• Stereo/Parallel/Bridged Mono mode selector switch
• Ground lift switch
• TourClass®protection circuits:
- ACL (Active Clip Limiting) prevents speaker damage with
gentle gain reduction at clip threshold.
- IGM (Instantaneous Gain Modulation) monitors connected
loads to detect conditions that may overstress output
devices.
- AutoRamp gradually increases gain to attenuator setting
level when amplifier is turned on.
- TourClass also includes comprehensive thermal management, and short circuit, DC voltage, turn-on/off transient,
current inrush and sub/ultrasonic input protection.
• Input sensitivity selection
• Recessed, stepped attenuators
• Front panel magnetic circuit breaker switch
• Modular construction
• Three-year warranty (parts and labor)
Protect
Clip
Active
Signal
Ch A
Protect
Clip
Active
Signal
Ch B
Power Specifications 8Ω Stereo 4Ω Stereo 8Ω Bridged
1kHz, 0.01% THD+N 150W 250W 500W
20Hz-20kHz, 0.1% THD+N 150W 200W 450W
-6
-10
-3
-15
-30
-80
-10
-15
-30
-80
-1
0dB
-6
-3
-1
0dB
Figures are Watts per channel, both channels driven.
HD2 POWER AMPLIFIER
SPECIFICATIONS
1kHz, 0.01% THD+N 20Hz-20kHz, 0.1% THD+N
8Ω Stereo Power
4Ω Stereo Power
8Ω Bridged Mono Power
Max RMS Output Voltage
(each channel)
Peak Output Voltage (each channel)
Frequency Response (+0 / -0.3dB, 1W/8Ω)
Power Bandwidth (rated power at 4Ω, 1% THD+N)
TourClass®Protection
THD+N
(rated power at 4Ω, 1kHz)
SMPTE IMD (rated power at 8Ω, 60Hz & 7kHz)
Damping Factor (10-400Hz at 8Ω)
Input CMRR (1kHz)
Input Sensitivity (rated power at 8Ω )
Voltage Gain
Input Impedance (balanced/unbalanced)
Hum and Noise
(“A” weighted, full power, 4Ω)
Crosstalk (“A” weighted, full power, 4Ω)
Input Connectors
(per channel)
Output Connectors (per channel)
Filter Storage
Power Supply
(factory configured)
Idle Current Draw 120V
1/8 Power Curr. Draw
(typical music, 120V/4Ω)
1/3 Power Curr. Draw (continuous music, 120V/4Ω)
Max Curr. Draw (circuit breaker rating, 120V/4Ω)
Thermal Emissions (1/8 Power, 4Ω)
Thermal Emissions (1/3 Power, 4Ω)
Controls
LED Indicators
(per channel)
Construction
Dimensions
(Height x Width x Depth)
Gross Weight, Net Weight
Warranty
Dealer-Configurable Gain/Sensitivity Options Factory Standard X45 .775V
160W 150W
250W 200W
500W 450W
44V
62V
20Hz-20kHz, -3dB@135kHz
20Hz-20kHz, -.9dB/+.15dB
ACL, IGM, AutoRamp, short circuit, DC voltage,
turn-on/off transient, current inrush, sub/ultrasonic input.
<0.01%
<0.01%
368:1
> - 60dB
0.775V standard (see table below)
X45 standard (see table below)
>20kΩ/>10kΩ
-105dB
> - 60dB
Class
AB
Female XLR (pin 2+, dealer config. for pin 3+), TRS (tip+)
5-way output binding posts or Speakon connectors
20,000 µF
100V-240V, 50-60Hz
1.2A
3.25A
5.5A
9.0A
1119 BTU/hr
1607 BTU/hr
Cooling
Back-to-front via 2 rear panel mounted variable-speed DC fans
(filters removable without tools)
Front Panel: 2 attenuators
Rear Panel: signal ground lift switch, mode select switch
Clip/Limit, Signal, Temp/DC, Active
Steel chassis, 16 gauge. Double thickness in rack ear areas.
3.5" x 19" x 18" / 89 x 483 x 457mm
38 lbs. / 17.25 kg., 33 lbs. / 14.98 kg.
3 years, parts & labor
Gain Sens
Option 1 X40 .866V
Option 2 X20 1.73V
(market dependent)
Architect’s & Engineer’s Specifications
The power amplifier shall have two channels. At 8 ohms, 20Hz 20kHz, 0.1% THD, it shall deliver a minimum of 150 Watts per
channel. At 4 ohms, 20Hz - 20kHz, 0.1% THD, it shall deliver a
minimum of 200 watts per channel. In bridged mono mode with an
8 ohm load, 20Hz - 20kHz, 0.1% THD, it shall deliver a minimum
of 450 watts.
The amplifier shall have circuitry to protect itself from output short
circuits, thermal overload or other adverse load conditions. The
amplifier shall protect speaker loads from DC voltage on outputs.
The amplifier shall have active clip limiting and impedance sensing
circuitry. Output relays shall protect the speakers from amplifier
failure.
Two rear panel mounted variable speed DC fans (filters detachable
without tools) shall provide back to front air flow through the chassis.
Each channel shall have a standard (factory-set) input sensitivity of
0.775 Volts, and shall be fitted with an internal jumper which
allows the gain to be altered to X20 or X40. The hum and noise
level shall be 105 dB below rated output, “A” weighted.
IMD shall be less than 0.01% at rated power, 60Hz and
7kHz. The amplifier shall have a class AB output stage. The fre-
quency response shall be 20Hz-20kHz, +0, -0.3dB at rated power.
The amplifier will operate at 100V-240V, 50-60 Hz AC (configured
at factory). Maximum current draw shall not exceed 9 amperes at
120VAC (limited by front panel breaker for bench tests).
Front panel indicators shall include Active, Protect, Signal, and
Clip LED’s for each channel. Front panel attenuators shall be
recessed and detented.
Rear panel input connectors shall be female TRS and XLR type,
internally dealer-configurable for pin 2 (factory setting) or pin 3
positive. Output connectors shall be 5-way output binding posts. A
ground lift switch and a Stereo/Parallel/Bridged Mono mode operation switch shall be provided.
A rear-panel IEC AC mains socket (with power cord) or single AC
mains cord having an appropriate AC plug for the intended operating voltage shall be provided (market dependant).
The packaging of the amplifier shall allow for standard rack
mounting without requiring space between similar units. Optional
rack mount handles will be available. Dimensions shall be 19"
(483mm) wide, 3.5" (89mm) high and 18" (457mm) deep. The
amplifier shall weigh 33 lbs. (14.98 kg) net, and shall be designated
the Crest Audio model HD2.
SMPTE
Rear View
v. 1.1 5/21/97 C3400001
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á
L'HUMIDITÉ
Power figures are watts per channel, both channels driven.
Crest Audio reserves the right to make improvements in manufacturing or
design which may affect specification. Crest Audio specification literature
is available in electronic form to qualified users. Contact Crest Audio Inc.
for more information. © 1996 Crest Audio Inc.
+
+
+
A
A
B
B
A
A
B
643-106
A
AB
A
B
B
A
A
•
•
+
••
B
Designed & manufactured in the USA by:
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
2+
1
3-
Crest Audio Inc.
100 Eisenhower Dr., Paramus NJ 07652 USA
TEL: 201.909.8700 FAX: 201.909.8744
http://www.crestaudio.com
Printed in USA
Loading...