MAXIMUM AND MINIMUM
TEMPERATURES
The maximum and minimum recorded indoor and outdoor
temperatures will be automatically stored in memory.
To display them,
Press [ MEM ] once to display the maximum temperature
and again the minimum temperature. The respective
indicators, [ MAX ] or [ MIN ] will be displayed.
To clear the memory, hold down [ MEM ] for two seconds.
The maximum and minimum temperatures will be erased.
If you press [ MEM ] now, the maximum and minimum
temperatures will have the same values as the current ones
until different readings are recorded.
DISCONNECTED SIGNALS
If without obvious reasons the display of the outdoor
temperature goes blank, Hold [ ] for 2 seconds to
enforce an immediate search.
If that fails, check:
1. The remote unit is still in place.
2. The batteries of both the remote unit and main unit.
Replace as necessary.
Note: When the temperature falls below freezing point,
the batteries of outdoor units will freeze, lowering their
voltage supply and the effective range.
3. The transmission is within range and path is clear of
obstacles and interference. Shorten the distance when
necessary.
TRANSMISSION COLLISION
Signals from other household devices, such as door bells,
home security systems and entry controls, may interfere
with those of this product and cause temporarily reception
failure. This is normal and does not affect the general
performance of the product. The transmission and reception
of temperature readings will resume once the interference
recedes. Different channel may be reduce the interference.
HOW TO SET THE RADIO CONTROLLED CLOCK
*After the batteries are installed. The clock will
automatically search the radio signal. It takes about
3-5 minutes to finish this process.
*If the radio signal is received, the date & time will be set
automatically with radio control signal icon [ ] turns on.
*If the clock fails to receive the time signal, it will be with
the [ ] icon turns off. Then user can set the time manually.
*Radio-controlled signal will be scheduled to receive
every hour.
The alarm “ ” “ ” and “ Pre-AL” icons will be
displayed indicating which alarm is armed. You can also
arm or disarm an alarm by pressing the [Up], [Down] button
at alarm display mode.
Press MODE to return to clock display mode.
SNOOZE FEATURE
When the alarm sound is on, press the snooze key enter
snooze mode. After 8 minutes, it alarm sound will be
wake up automatically. The snooze cycle will be restart if
you press the snooze key again. If you leave the alarm sound
on for 2 minutes, it will enter snooze mode automatically
with maximum 3 times.
HOW TO STOP AN ALARM
Press [ALARM] on the unit to stop an alarm.
HOW TO SET AND ARM THE ALARM
To set an alarm,
1. Press [ALARM] once to display alarm time. If the alarm
is disarmed, the time will be displayed as “ OFF ”.
2. Hold [ALARM] for two seconds. The hour digits
will blink.
3. Enter the hour using [ ] or [ ].
4. Press [ALARM]. The minute digits will blink.
5. Enter the minutes using [ ] or [ ].
6. Press [ALARM] to exit.
7. Repeat the same procedure to set single alarm.
W
S
PRECAUTIONS
This product is engineered to give you years of satisfactory
service if you handle it carefully. Here are a few precautions:
1. Do not immerse the unit in water.
2. Do not clean the unit with abrasive or corrosive materials.
They may scratch the plastic parts and corrode the
electronic circuit.
3. Do not subject the unit to excessive force, shock, dust,
temperature or humidity, which may result in malfunction,
shorter electronic life span, damaged battery and
distorted parts.
4. Do not tamper with the unit's internal components. Doing
so will invalidate the warranty on the unit and may cause
unnecessary damage. The unit contains no
user-serviceable parts.
5. Only use fresh batteries as specified in the user's manual.
Do not mix new and old batteries as the old ones may leak.
6. Always read the user's manual thoroughly before
operating the unit.
ALARM FEATURE
* Weekday Alarm
The alarm sound will be activated and the icon will be
flashed on weekday when it is armed and the alarm time
is reach.
* Single Alarm
The alarm sound will be activated and the icon will be
flashed once when it is armed and the alarm time is reach.
Once it finished, it will be disabled automatically.
* Pre-Alarm
The pre-alarm sound will be activated and the icon will be
flashed if outdoor temperature under or equal zero degree.
Which is programmable 15, 30, 45, 60 or 90 minutes
earlier than the weekday alarm or single alarm time.
- Receiving
- Strong - No singal
No symbol
-signal recepttion
disabled
CALENDAR CLOCK DISPLAY MODES
The clock and the calendar share the same section of the
display. The calendar is displayed in a day-month format.
Each press on the MODE button will change the display
between clock with second, clock with day of week,
zone time with second and day-month.
HOW TO SET THE CLOCK MANUALLY
To set the clock manually, hold MODE for two seconds it
will show the year. Use [ ] or [ ] to change it.
Press MODE to confirm. Repeat the same procedure to set
the month, date, date-month format, 12/24, hour, minute,
display language, zone time offset and ˚C/˚F.
During the setting, press and hold [ ] or [ ] will
increase or decrease the value rapidly.
For display language, you can choose among English-En,
German-DE, French-Fr, Italian-IT and Spanish-SP.
- in that order. If there is an item you do not wish to change,
simply press [ MODE ] to bypass the item.
When you finished the change, press [ MODE ] to exit.
The display will return to the clock mode.
27 28
2625