Crest PRO9200 Specifications
Rated power bridge mode 4 Ohms
6,500 Watts @ 1 kHz at <0.1% T.H.D.
Rated power (2 x 2 Ohms)
3,250 Watts per channel @ 1 kHz <0.1% T.H.D.
both channels driven
Rated power (2 x 4 Ohms)
2,200 Watts per channel @ 1 kHz at <0.05%
T.H.D. both channels driven
Rated power (2 x 8 Ohms)
1,300 Watts per channel @ 1 kHz at <0.025%
T.H.D. both channels driven
Rated power (1 x 2 Ohms)
4,200 Watts @ 1 kHz at <0.1% T.H.D.
Rated power (1 x 4 Ohms)
2,550 Watts @ 1 kHz at <0.05% T.H.D.
Rated Power (1 x 8 Ohms)
1,450 Watts @ 1 kHz at <0.025% T.H.D.
Minimum load impedance
2 Ohms
Maximum RMS voltage swing
113 Volts
Frequency response
10 Hz - 100 kHz; +0, -3 dB at 1 Watt
Power bandwidth
10 Hz - 30 kHz; +0, -3 dB at rated 1000 Watts
8 Ohm power
T.H.D. (2 x 2 Ohms)
<0.1% @ 2,350 Watts per channel from 20 Hz to
20 kHz
T.H.D. (2 x 4 Ohms)
<0.1% @ 1,950 Watts per channel from 20 Hz to
20 kHz
T.H.D. (2 x 8 Ohms)
<0.1% @ 1,200 Watts per channel from 20 Hz to
20 kHz
Input CMRR
>-85 dB @ 1 kHz
Voltage gain
x 40 (32 dB) or x 20 (26 dB)
Crosstalk
>-70 dB @ 1 kHz at rated power @ 8 Ohms
Hum and noise
>-113 dB,“A” weighted referenced to rated
power @ 8 Ohms
Slew rate
>10V/us
Damping factor (8 Ohms)
>300:1 @ 20 Hz - 1 kHz
Pro
9200
Series
Professional Power Amplifier
Specifications
Specifications
Pro
9200
Series
Professional Power Amplifier
Crest Audio Inc.
16-00 Pollitt Dr. Fair Lawn, NJ 07410 USA
TEL: 201.909.8700 FAX: 201.909.8744
www.crestaudio.com
Crest Audio reserves the right to make improvements in manufacturing or design which may affect specifications.
Phase response
+5 to -15˚ from 20 Hz to 20 kHz
Input sensitivity (x 40)
2.35 Volts ±3% for 4 Ohm rated power, 2 Volts
±3% for 1 kHz 2 Ohm rated power
Input sensitivity (x 20)
4.7 Volts ±3% for 4 Ohm rated power, 4 Volts
±3% for 1 kHz 2 Ohm rated power
Input impedance
15 k Ohms, balanced
Current Draw @ 1/8 power
3,350 Watts @ 2 Ohms; 2,200 Watts @ 4 Ohms
Current Draw @ 1/3 power
7,300 Watts @ 2 Ohms, 5,000 Watts @ 4 Ohms
Cooling
Two temperature dependant variable speed
80 mm high output DC fans
Controls
Two front panel attenuators, rear panel mode
switch and gain select switch
Indicator LEDs
2 ACL (clip limiting), 2 signal presence, 2 active status,
2 DC protect, 2 temperature limit
Protection
Thermal, DC, turn-on bursts, subsonic, incorrect
loads
Connectors
XLR, Speakon and Binding Post speaker output,
120 Volt 30 amp mains, 240/230 Volt 20 amp
IEC mains
Construction
16 ga. steel with 5 mm aluminum front panel
Dimensions
89 mm x 483 mm x 311 mm + 38 mm for rear
support ears and connectors
(3.5" x 19" x 12.25" + 1.5")
Net weight
12.34 kg. (27.2 lbs.)
Gross weight
14.65 kg. (32.3 lbs.)
Warranty
Five years parts and labor
All power measurements made at 120 VAC. 2 Ohm sine wave power is time limited by magnetic
circuit breaker and is internal temperature dependant.
v. 1.1 10/23/03
80304977
Loading...