Cressi T10, T10 SC Cromo, MC9, MC9 S.C., MC5 Directions For Use Manual
...
erogatori
regulators
detendeur
atemregler
regulador
пользователя
呼吸调节器
Manuale d’uso
Direction for use
Manuel d’instructions
Bedienungsanleitung
Manual de istrucciones
Pуководство
潜水呼吸调节器使用手册
made in Italy
44
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .page 45
Main Components . . . . . . . . . . . . . . . . . .page 45
1) FIRST STAGES . . . . . . . . . . . . . . . . . . . . . .page 47
1.1 T10 - T10 S.C.-T10 SC Cromo . . . . . . . . . . .page 48
1.2 MC9 - MC9 S.C. . . . . . . . . . . . . . . . . . . . . . . .page 52
1.3 MC5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 54
1.4 AC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 56
1.5 Performance . . . . . . . . . . . . . . . . . . . . . . . . . .page 57
2) SECOND STAGES . . . . . . . . . . . . . . . . . . .page 61
2.1 Galaxy Adjustable/Master / Master Cromo / Galaxy /
Octopus MG Balanced . . . . . . . . . . . . . . . . .page 62
2.2 Master / Master Cromo / Galaxy,
Octopus MG Balanced
disassembly and maintenance . . . . . . . . . .page 65
2.3 XS Compact Pro / XS Compact / Octopus . .page 66
2.4 XS Compact Pro / XS Compact
Disassembly and maintenance . . . . . . . . . . .page 69
2.5 XS2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 70
2.6 Performance . . . . . . . . . . . . . . . . . . . . . . . . . .page 73
3) USE AND MAINTENANCE . . . . . . . . . . .page 77
3.1 Use of the regulator and risk assessment .page 78
3.2 Checks before use . . . . . . . . . . . . . . . . . . . . .page 78
3.3 Mounting the regulator to the tank . . . . . . .page 79
3.4 Use of the regulator in cold water . . . . . . . . page 80
3.5 Care and maintenance
of the equipment . . . . . . . . . . . . . . . . . . . . . .page 80
3.5.1 Caring for the equipment . . . . . . . . . . . . . . . .page 80
3.5.2 Equipment maintenance . . . . . . . . . . . . . . . .page 81
3.6 Use with Nitrox mixtures . . . . . . . . . . . . . . . .page 81
3.7 Maintenance/recording of procedures
(Service Record) . . . . . . . . . . . . . . . . . . . . . .page 83
3.8 Cressi-sub Certified Combinations . . . . . . .page 84
4) TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 303
TABLE OF CONTENTS
ENGLISH
Introduction
Congratulations! Continual research and evolution carried out at
our technical centres, together with Cressi-sub’ s usual reliability,
have led to the product you just purchased, which will allow you
to dive comfortably and safely for a long time.
All Cressi-sub regulator are certified to 146 ft (50 m), and some
for use in cold water with temperatures below 10° C, having
passed the stringent operations testing at 4° (+0-2) set forth
under the standard EN 250:2014 (and all previous editions) in
compliance with new EU regulation 2016/425 (ex 89/686/CEE).
This regulation establishes the conditions for bringing to market
and the essential minimum safety requirements for Personal Protective Equipment (PPE). It will officially take effect April 21, 2018,
abrogating the previous Directive 89/686/EEC, upon the conclusion of a transitional period granted to manufacturers of PPE.
Main Components
Regulators’ main task is reducing the pressure of the compressed air contained in the tank to the same level as the environment’ s, supplying breathable air when required by the diver.
They are composed of a “first stage”, working as main pressure
reducer and a “second stage” (kept in the diver’ s mouth), which
adjusts the pressure precisely to the same value as the environment’ s. The regulator is part – together with tank, valves and
sling – of a complete underwater breathing system, known as
“SCUBA” (Self Container Underwater Breathing Apparatus).
This handbook describes all models of Cressi-sub range, all realized in high quality materials to guarantee pleasant dives and
high performance, together with the easiest ways of use andmaintenance. The instructions and directions found in this manual
are based on the most up-to-date information about the equipment available before printing.
Cressi Sub reserves the right to make changes at any time.
NOTE: The instructions and directions found in this manual are
based on the most up-to-date information about the equipment available before printing. Cressi Sub reserves the right to
make changes at any time.
NOTE: This handbook does not replace a diving training course! All Cressi-sub devices must be used by divers who have
attended regular courses held by certified trainers.
Using underwater devices without a licence or the necessary
technical training may be dangerous for the diver’ s safety and
life itself.
Besides, in order to guarantee the maximum safety, the devices must be serviced only by the producer or an authorizedcentre.
You can find your authorized Cressi-Sub center by
asking your dealer, or Cressi Sub S.p.A. itself
(email: info@cressi.com).
WARNING: CRESSI-SUB DECLINE ANY RESPONSIBILITY FOR ANY SERVICING CARRIED OUT BY
UNAUTHORIZED PERSONNEL.
WARNING: SCUBA devices complying with EN
250:2014 standard must not be used by more
than a diver at the same time.
WARNING: in case the components of a SCUBA
are set and used by more than a diver at the same
time, their performance in cold water might not
satisfy the requisites prescribed by EN 250:2014
standard.
WARNING: if the components of the SCUBA
equipment are configured and used simultaneously
by multiple divers, the equipment may not be used
at depths of greater than 30 meters, or at water
temperatures below 10 °C (if specified).
45
Direction for use regulators
FIRST STAGES
1.1 - T10 - T10 S.C. - T10 SC Cromo
1.2 - MC9 - MC9 S.C.
1.3 - MC5
1.4 - AC2
1.1. - T10 - T10 S.C.-T10 SC Cromo
The T10 balanced diaphragm first stage features a lightweight
structure of compact design, protected by the special and innovative PVD (Physical Vapor Deposition) treatment, which creates
a highly resistant surface coating with extraordinary chemicalphysical characteristics and a high technical, very pleasing appearance. Unlike the T10 version, the Cromo version has a
protective surface coating of electroless chrome plating.
The ergonomics of the T10 balanced diaphragm first stage presents the functioning mechanism arranged perpendicular to the
air entry axis that thereby forms a “T” profile designed to guarantee perfect arrangement of the HP and LP hoses, avoiding interference with the equipment connected to the first stage; reduced
size (particularly used in the SC version particularly suited to cold
water), as well as additional inspection capacity and access to the
HP valve mechanism to simplify maintenance and disassembling
of the regulator.
It provides outstanding respiratory performance, constant in any
use condition, thanks to the compensated diaphragm mechanism that enables maximum respiratory comfort to be obtained
during any dive phase, from the surface to maximum depths.
In fact, the regulator provides the same intermediate pressure independent of the pressure contained in the tanks and maintains
performance at any depth.
Contrary to most regulators currently on the market, offering optimum performance when the tank is full at maximum working
pressure, the T10 first stage was designed to offer optimum performance when the tank is close to empty.
This “hyper balancing” feature was possible using a system that
adapts intermediate pressure taking into account the air density
as the depth increases and the progressive increase in pressure
drop as the tank empties.
Thanks to this feature, the T10 first stage assists the diver in the
dive, guaranteeing the highest working performance which increases further during the notoriously critical surfacing phase of
surfacing.
The compensated diaphragm mechanism phase, with a "T" air
entry, or rather the HP valve arranged perpendicular to the air
entry axis further guarantees considerable passage of air quantity
with a pressure drop, between the inhalation and exhalation
phase, which is reduced considerably.
These characteristics are the result of innovative technical solutions in the design and make the 1st stage among the smallest
and lightest regulators on the market and one of the top performing in its category.
In this first stage (Fig. 1), the flexible diaphragm protects and seals
the mechanism inside the system and transmits pressure variations in the water to the high pressure valve.
fig. 1
48
FIRST STAGES
ENGLISH
The HP poppet valve, which is extremely resilient and easily replaced during periodic maintenance, is manufactured in the latest
generation thermoplastic elastomers. This valve boasts the exclusive feature of sliding inside a special lined cylinder, also manufactured in self-lubricating thermoplastic material. The inner surface of
this cylinder, which is completely free of oxidation phenomena,
drastically reduces friction and makes the valve stroke extremely
fluid and precise, guaranteeing optimum respiratory comfort. The
HP poppet valve can also work perfectly guided on a pneumatic
seal compartment, guaranteed to last long thanks to the special
design of the piston sleeve that hinges the valve, without even
making it rotate on its own axis. By doing so, the 1st stage performance can be kept constant and unchanged over time.
The HP valve closure nozzle, manufactured in stainless steel 316, is
interchangeable to facilitate periodic maintenance of the 1st stage.
Air entry in the first stage is protected by a sintered conical filter in
compact, sintered and nickel-plated phosphor bronze microspheres, to enable better air filtering thanks to the broader filtering
surface guaranteed by the shape which also guarantees the passage of an elevated air flow, typical of this regulator and withholds
any impurities from tank and valve.
The intermediate pressure regulation system of the T10 balanced
diaphragm 1st stage follows the tradition of all Cressi-sub first
stages, allowing convenient and fast regulation of intermediate
pressure without having to disassemble parts of the regulator.
WARNING: intermediate pressure regulation should only be
carried out by authorised Cressi-sub centres and the calibration
values CANNOT and MUST NOT be changed by the user, to
avoid prejudicing the good working order of the regulator. We
cannot be held in any way liable for any intervention carried out
by staff unauthorised by Cressi-sub.
The Cressi-Sub authorised centres can be indicated
by retailers or, alternatively by Cressi Sub s.p.a.
(email: info@cressi.com).
The balanced diaphragm first stage features a lightweight structure
of compact design, made from seagoing brass, protected on the
surface by means of a PVD (Physical Vapor Deposition) treatment
(version T10SC) or coated with chromed copper (version T10 S.C.
Cromo); the interior components are made of stainless steel,
chromed brass and new generation thermoplastic resins.
It avails of 4 low pressure (LP) 3/8” ports, adequately angled for
optimal distribution of the hoses that avoid interference with the
attached equipment, and 2 high pressure (HP) 7/16” ports with a
micrometric perforation for air release, ensuring maximum safety
also in the event of accidental breakage of the high pressure
hose, avoiding the risk of rapid tank emptying.
WARNING: on the HP ports of the first stage, an underwater
gauge and/or an underwater computer must be connected to
also incorporate the gauge function. Since the tanks are not
equipped with a reserve device, it is absolutely indispensable to
use a gauge that indicates progressive air consumption when
diving and which clearly highlights the reserve pressure has been
reached, which should be considered as unusable air for the
purpose of the dive itself, but only as an emergency air reserve.
Diving without a gauge is dangerous because there is no way of
controlling consumption and you can suddenly find yourself without air during a dive, putting your life in serious danger.
Connection of the first stage to the tank valve can take place
using an international connection, using a new yoke with an extremely modern design or a threaded coupling DIN 300 bar, both
according to EN ISO 12209 as referenced in the standard EN
250:2014.
As with all regulators in the Cressi-sub range, the T10 first stage
offers the possibility of making certain manufacturing components of the regulator compatible, allowing interchanging parts
with other diaphragm first stages in the current range.
49
FIRST STAGES
Use of the T10 balanced diaphragm first stage is advised, compared to the piston models, for diving in waters full of suspended
particles or dissolved mineral salts, or for use in cold water (with
temperatures under 10°C), because all parts of the regulator
mechanism are insulated for contact with water.
For diving in extreme conditions we recommend using combinations with the T10SC or the T10 Cromo SC versions equipped with
the Seal Chamber (S.C.)
WARNING: to deal with diving in cold water (temperature
<10°C or < 50°F) Cressi-sub recommends use of a tank
equipped with a pillar valve with two independent ports outlet,
where two complete regulators can be connected.
WARNING: adequate technical preparation is necessary to
deal with diving in cold water (temperature <10°C or < 50°F ).
Cressi-sub recommends you carry out this type of diving after
taking a specific course given by qualified instructors. It is important not to wet the regulator before use and then expose it
to air (which can be well under zero degrees). Do not use the
purge button, particularly with the regulator level with Venturi
effect in the “dive” position. If possible, keep the regulator in
warm surroundings when not in use.
The Seal Chamber is used to make the T10 balanced diaphragm
first stage completely waterproof, avoiding water entry not only
inside, but also in contact with the diaphragm and the calibration
spring on the 1st stage, thereby creating an air chamber upstream of the regulator and its components, working like a proper
thermal barrier. All problems are therefore avoided relating to
contact with water full of suspended particles, sand, dissolved
mineral salts and with cold water which, especially at temperatures below 10°C could form the foundation for possible freezing
of the regulator.
The Seal Chamber (fig.2) consists of a special metal insert with a
particular “radiator” shape designed to increase thermal ex-
change between the ambient temperature and the temperature
inside the regulator, preventing its possible freezing effect, and a
metal cap containing a silicone membrane inside. This, on warning of the ambient pressure variations, inverts and thereby transmits oscillations to the ambient pressure transducer beneath
which, coming in contact with the main diaphragm, acts as a
transmission element which transfers all information on the extreme pressure variations to the diaphragm. The main diaphragm
which, in turn, protects and seals the mechanism inside the system, then transmits the pressure variations of the water to the
high pressure valve.
NOTE: before assembling the Seal Chamber S.C. the
balanced diaphragm first stage must be calibrated. To ensure
the regulator works properly, strictly comply with the calibration
values outlined in the regulator performance table. Regulator
calibration is not restricted by the ambient pressure variations
transmission disk.
fig. 2
50
FIRST STAGES
ENGLISH
WARNING: intermediate pressure adjustment should only
be carried out by authorised Cressi-sub centres and the calibration values CANNOT and MUST NOT be changed by the
user, to avoid prejudicing the good working order of the regulator. We cannot be held in any way liable for any intervention
carried out by staff unauthorised by Cressi-sub.
The Cressi-Sub authorised centres can be indicated
by retailers or, alternatively by Cressi Sub s.p.a.
(email: info@cressi.com).
The T10 first stage can therefore be used in cold water (with
water temperature below 10 °C/50 °F), since it complies with Directive 89/686/EEC dated 21/12/1989, checked and certified by
Test Authority No. 0474 RINA located in Genoa, tested in compliance with standard EN 250:2014 that establishes the requirements for Personal Protective Equipment (PPE) category III. It
therefore bears the CE marking followed by identification of the
certification authority (0474) that checks its manufacture pursuant to module B+C2 of EU Regulation 2016/425. The standard
also dictates the essential health and safety requirements for Category III PPE and governs the conditions for bringing it to market.
The considerable technical solutions, combined with the high
quality of the materials used, ensure that this first stage regulator
is fully reliable and capable of providing the highest performance
extended over time.
Additional important information relating to our equipment can be
found on the website www.cressi.com
51
FIRST STAGES
1.2 - MC9 - MC9 S.C.
The MC9 - MC9 S.C. balanced diaphragm first stage features a
lightweight structure of compact design, enclosed in an “aesthetic-protective” shell made from a special elastomer, specially
conceived to protect the regulator from impact.
It guarantees high breathing performance in every condition,
thanks to its balanced diaphragm mechanism, allowing the
maximum breathing comfort in every diving phase, starting from
the surface up to the maximum depth. The regulator, in fact,
supplies the same intermediate pressure independently from
the tank pressure, and keeps its performance independently
from the depth.
Unlike the most regulators on the market, offering their best
performance when the tank is loaded at its maximum working
pressure, MC9 first stage was designed to give its best performance when the tank is about to empty. This ”hyper-balanc-
ing” feature is possible thanks to a system of regulation of the
intermediate pressure, which takes into account both the
air density as the depth increases and the progressive pressure
decrease due to the tank running down.
Thanks to this feature, MC9 first stage assists the diver during
the whole dive, guaranteeing the highest performance, which
improves during the most critical phase of surfacing.
Moreover, the balanced diaphragm mechanism, delivering air
“online”, allows remarkable amounts of air to pass, by a very small
pressure decrease between inhalation and exhalation phases.
These features are the results of several innovating technical
solutions taken by designing MC9 1st stage, making it one of the
best performing small and light regulators on the market.
In this first stage (fig. 3), the elastic diaphragm protects and seals
the system’ s inner mechanism, transmitting the changes of
water pressure to the high pressure valve.
The latter is made of special thermoplastic state-of-the art elastomers, is highly resistant and easily replaceable. It boasts the
exclusive innovation of sliding inside a special self-lubricating
cylinder in a special thermoplastic material. The cylinder’ s inner
surface is completely free of oxidation, reduces any friction dramatically and makes the valve slide in an extremely easy and
precise way, guaranteeing the highest breathing comfort.
The HP seat is made of 316 stainless steel and is interchangeable, in order to make the maintenance of the 1st stage easier.
The passage of air through the first stage is protected by a special cup-shaped conical sintered filter, retaining any impurity from
tank and valves.
The regulation system of intermediate pressure in MC9 balanced
diaphragm first stage is the same as all other Cressi-sub first
stages, which allows an easy and quick adjustment of intermediate pressure without having to disassemble any component of
the regulator.
fig. 3
52
FIRST STAGES
ENGLISH
WARNING: intermediate pressure must be set only at au-
thorized Cressi-sub centres; the setting values must NOT and
can NOT be modified by the user, in order not to affect the
good working of the regulator. Cressi-sub decline any responsibility
for any intervention carried out by unauthorized personnel.
You can find your authorized Cressi-Sub center by
asking your dealer, or Cressi Sub S.p.A. itself
(email: info@cressi.com).
Balanced diaphragm first stage features a light compact structure
in chromium-plated brass with inner components in stainless steel,
chromium-plated brass and state-of-the-art thermoplastic resins.
It is supplied with four low pressure (LP) 3/8” ports - specially
angled to allow the best hose positioning, avoiding any encumbrance among different devices - and two high pressure (HP)
7/16” ports with a micrometric air exit hole, guaranteeing maximum safety even in the case of damage to the high pressure
hose, since it greatly reduces air loss from the thank.
WARNING: an underwater pressure gauge or a computer
with such function must be connected with the HP ports of
the first stage.
Since the tanks are not supplied with a reserve device, a pressure gauge must always be used, reporting the progressive
air consumption by diving and the reaching of reserve pressure, which has to be considered as not to be used by diving
but only as emergency air supply.
Diving without any gauge is dangerous, since the diver can
not control his own air reserve, which might suddenly run out,
at his own high risk.
The first stage can be connected to the tank valve with an international, by means of an extremely modern designed bracket, or
with a threaded connection DIN 300 (EN ISO 12209) bar, bothcomplying with EN 250:2014 standard.
Like all Cressi-sub regulators, whose components are often interchangeable one with the other, MC9 is compatible with other
diaphragm first stages of the present range.
MC9 balanced diaphragm first stage, like other Cressi-sub diaphragm first stages as well, is to be recommended rather than other
piston models, by diving in suspension or mineral salts rich water,
or in cold water at temperature lower than 10 °C/50 °F. All innercomponents of the regulators are in fact perfectly watertight.
For diving in extreme conditions we recommend using combinations with the MC9SC version, equipped as standard with the Seal
Chamber (S.C.).
WARNING: In case of dives in cold water (temperature less
than 10°C/50° F), Cressi-sub recommend to use a tank supplied with a valve featuring two separate outlet ports, with
which two complete regulators are to be connected.
WARNING: diving in cold water at temperature lower than
10°C/50 °F requires a special technical training. Cressi-sub
recommend such diving only after attending a special training
course by certified trainers. The regulator must absolutely not
get wet and exposed to freezing air before use. Do not press
the discharge button, particularly when the Venturi effect
adjustment lever is on “dive”. If possible, keep the regulator in
a warm place before use.
The Seal Chamber’ s task is to make MC9 balanced diaphragm
first stage perfectly watertight, preventing water from seeping
inside or on the diaphragm and the main spring: it works as an air
chamber above the regulator and its components, like a real
thermal barrier. It avoids any problem caused by contact with
suspension, sand, mineral salts rich water and with cold water,
which might eventually cause the regulator to freeze, especially
at temperature lower than 10° C/50° F.
fig. 4
53
FIRST STAGES
The Seal Chamber is composed of a metal cap containing a silicon seal. The seal responds to any environmental pressure
change bending towards the inside and transmitting it to the
underlying plate; the latter transmits such information to the main
diaphragm. The main diaphragm protects and seals the device’
s inner mechanism, transmitting pressure changes to the high
pressure valve.
NOTE: before assembling the Seal Chamber S.C. the
balanced diaphragm first stage must be set. In order to get
the regulator to work perfectly, the setting values must be
strictly those reported in the regulator’s performance table.
The setting is independent from the plate transmitting environmental pressure changes.
WARNING: intermediate pressure must be set only at
authorized Cressi-sub centres, while the setting values can
NOT and must NOT be modified by the user, in order not to
affect the regulator’ s performance. Cressi-sub decline any
responsibility for any intervention carried out by unauthorized
personnel.
You can find your authorized Cressi-Sub center by
asking your dealer, or Cressi Sub S.p.A. itself (email:
info@cressi.com).
The MC9 S.C. first stage can therefore be used in cold water (with
water temperature below 10 °C/50 °F), since it complies with Directive 89/686/EEC dated 21/12/1989, checked and certified by
Test Authority No. 0474 RINA located in Genoa, tested in compliance with standard EN 250:2014 that establishes the requirements
for Personal Protective Equipment (PPE) category III. It therefore
bears the CE marking followed by identification of the certification
authority (0474) that checks its manufacture pursuant to module
B+C2 of EU Regulation 2016/425. The standard also dictates the
essential health and safety requirements for Category III PPE and
governs the conditions for bringing it to market.
Its remarkable technical features, together with its high quality
materials, make this first stage a highly reliable regulator, guaranteeing best performances for a long time.
Visit our web-site www.cressi.com, where you can find further information relating to your safety.
1.3 – MC5
MC5 balanced diaphragm 1st stage features an extremely light
and compact structure enclosed in an “esthetical-protective”
shell of a special elastomer, designed to protect the regulator
from collision.
It guarantees high breathing performance in every condition,
thanks to its balanced diaphragm mechanism, allowing the
maximum breathing comfort in every diving phase, starting from
the surface up to the maximum depth. The regulator, in fact,
supplies the same intermediate pressure independently from
the tank pressure, and keeps its performance independently
from the depth.
The balanced diaphragm mechanism, delivering air “on line”,
allows remarkable amounts of air to pass, by a very small pressure decrease between inhalation and expiration phases.
These features are the results of innovating technical solutions
taken by designing MC5 1st stage, making it one of the best
performing small and light regulators on the market.
fig. 5
54
FIRST STAGES
55
ENGLISH
In this first stage (fig. 5), the elastic diaphragm protects and seals
the system’ s inner mechanism, transmitting the changes of
water pressure to the high pressure valve.
The latter is made of special thermoplastic state-of-the art elastomers, is highly resistant and easily replaceable. It boasts theexclusive innovation of sliding inside a special self-lubricating cylinder in
a special thermoplastic material. The cylinder’ s inner surface is completely free of oxidation, reduces any friction dramatically and makes
the valve slide in an extremely easy and precise way, guaranteeing
the highest breathing comfort.
The passage of air through the first stage is protected by a special
cup-shaped conical sintered filter, retaining any impurity from tank
and valves.
The regulation system of intermediate pressure in MC5 balanced diaphragm first stage is the same as all other Cressi-sub first
stages, allowing an easy and quick adjustment of intermediate pressure without having to disassemble any component of the regulator.
WARNING: intermediate pressure must be set only at
authorized Cressi-sub centres, while the setting values can
NOT and must NOT be modified by the user, in order not to
affect the regulator’ s performance. Cressi-sub decline any
responsibility for any intervention carried out by unauthorized
personnel.
You can find your authorized Cressi-Sub center by
asking your dealer, or Cressi Sub S.p.A. itself
(email: info@cressi.com).
Balanced diaphragm first stage features a light compact structure in chromium-plated brass with inner components in stainless steel,
chromium-plated brass and state-of-the-art thermoplastic resins.
It is supplied with three low pressure (LP) 3/8” ports - specially
angled to allow the best hose positioning, avoiding any encumbrance among different devices - and a high pressure (HP)7/16”
port with a micrometric air exit hole, guaranteeing maximum safety even in the case of damage to the high pressurehose, since it prevents the tanks from emptying.
WARNING: an underwater pressure gauge or a compu-
ter with such function must be connected with the HP port of
the first stage.
Since the tanks are not supplied with a reserve device, a pressure gauge must always be used, reporting the progressiveair
consumption by diving and the reaching of reserve pressure,
which has to be considered as not to be used by diving but only
as emergency air supply.
Diving without any gauge is dangerous, since the diver can
not control his own air reserve, which might suddenly run out,
at his own high risk.
The first stage can be connected to the tank valve with an international, by means of an extremely modern designed bracket,
orwith a threaded connection DIN 300 bar (4350 psi) (EN ISO
12209), both complying with EN 250:2014 standard.
Like all Cressi-sub regulators, whose several components are
interchangeable one with the other, MC5 is compatible with
other diaphragm first stages of the present range.
MC5 balanced diaphragm first stage, like other Cressi-sub
diaphragm first stages, having all inner components watertight,
is to be recommended, rather than other piston models, by
diving in suspension or mineral salts rich water.
MC5 conforms to EU Regulation 2016/425, having been tested
and certified by Notified Body number 0474, RINA, with registered
office in Genoa, with testing conducted pursuant to standard EN
250:2014 which specifies the requirements for class III Personal
Protective Equipment (PPE), and therefore it bears the CE mark
followed by the ID data of the notified body (0474) pursuant to
form B+C2 of EU regulation 2016/425.
Its remarkable technical features, together with its high quality
materials, make this first stage a highly reliable regulator, guaranteeing best performances for a long time.
Visit our web-site www.cressi.com, where you can find further information relating to your equipment.
FIRST STAGES
1.4 - AC2
AC2 regulator has the task to reduce the tanks’ pressure. It isconnected
to the second stage by means of a hose supplying the diver with
breathable air at environmental pressure. The first stage’ s main task is
therefore to reduce the tanks’ air to an intermediate pressure, about
10 bar (145 psi) higher than the environmental.
Small dimensions, light weight, extremely simple structure, special sturdiness and easy maintenance: here are the main features of this in-line
first stage, offering as high performances as a balanced piston model’s.
Its compact and attractive design features four low pressure
3/8” ports in pairs, with preset angles to allow easy connection with
any accessory equipment. The setting is easily performed thanks to
the special revolving ring system, allowing a quick, precise and continuous adjustment, without having to disassemble the regulator.
WARNING: intermediate pressure must be set only at
authorized Cressi-sub centres; the setting values must NOT
and can NOT be modified by the user, in order not to affect
the good working of the regulator. Cressi-sub decline any
responsibility for any intervention carried out by unauthorized
personnel.
You can find your authorized Cressi-Sub center by
asking your dealer, or Cressi Sub S.p.A. itself
(email: info@cressi.com).
Inside, a conical filter provides a filtering action 200% higher than
a standard flat filter.
Airflow capacity is remarkable, due to new larger air ports, offering unequalled performance in this class of regulators.
Both international yoke and DIN (at 200 or 300 bar) (2900÷4350
psi) connection are fully interchangeable and are replaced with
each other very quickly (only at authorized Cressi-sub centres).
Its satin finish guarantees the regulator’ s best surface performance, while contributing to its outstanding strength and reliability. The first stage is manufactured with the finest materials and
Cressi-sub experience.
The first stage can be connected with the tank’ s valve either
with an international through an extremely modern designed
bracket, or with a threaded connection DIN (EN ISO 12209), both
complying with EN 250:2014 standard. Should the tank sused
have a working pressure higher than 200 bar (2900 psi), a DIN
connection is recommended.
Besides its technical innovations, this first stage differs from previous models as to its new esthetical look, enriched with careful
particulars in its finishing as well. It is a top quality high technology
regulator, showing a pleasant as well as aggressive look, united
with outstanding sturdiness and easy mechanics, which allows
an easy and simple maintenance.
The AC2 first stage conforms to EU Regulation 2016/425, having
been tested and certified by Notified Body number 0474, RINA, with
registered offices in Genoa, with testing conducted pursuant to standard EN 250:2014 which specifies the requirements for class III Personal Protective Equipment (PPE), and therefore it bears the CE
mark followed by the ID data of the notified body (0474) pursuant to
form B+C2 of EU regulation 2016/425.
Its remarkable technical solutions, together with high quality
materials, make this first stage a highly reliable regulator, offering
top quality performance for a long time.
Visit our web-site www.cressi.com, where you can find further
information relating to your equipment.
fig. 6
56
FIRST STAGES
Direction for use regulators
1.5 - Performance First Stages
1.5 - Performance
Working pressure (INT connection)
Working pressure (DIN connection)
Calibration pressure (200 bar feeding)
Air supply
High pressure (HP) ports
Low pressure (LP) ports
Weight without hose MC9
Weight without hose MC9 SC
0÷232 bar - (0÷3365 psi)
0÷300 bar - (0÷4350 psi)
10 bar - (145 psi)
4500 l/min (*)
2
4
590 gr (INT) - 450 gr (DIN)
650 gr (INT) - 510 gr (DIN)
MC9 / MC9 S.C.
Working pressure (INT connection)
Working pressure (DIN connection)
Calibration pressure (200 bar feeding)
Air supply
High pressure (HP) ports
Low pressure (LP) ports
Weight without hose MC5
0÷232 bar - (0÷3365 psi)
0÷300 bar - (0÷4350 psi)
10 bar - (145 psi)
3000 l/min (*)
1
3
450 gr (INT) - 350 gr (DIN)
MC5
(*) Values measured at LP port with second stage connected and tank pressure at 200 150 bar (2900 2175 psi)
(*) Values measured at LP port with second stage connected and tank pressure at 200 150 bar (2900 2175 psi)
Working pressure (INT connection)
Working pressure (DIN connection)
Calibration pressure (with 200 bar supply)
Air supply
High pressure (HP) ports
Low pressure (LP) ports
Weight without hose T10 SC
0÷232 bar
0÷300 bar
10 bar
4500 l/min (*)
2
4
720 gr (INT) - 602 gr (DIN)
T10 / T10 S.C. / T10 S.C. Cromo
(*) Values measured on LP port with second stage connected and 200 150 bar pressure in the tanks.
58
ENGLISH
1.5 - Performance
Working pressure (INT connection)
Working pressure (DIN connection)
Calibration pressure (200 bar feeding)
Air supply
High pressure (HP) ports
Low pressure (LP) ports
0÷232 bar - (0÷3365 psi)
0÷300 bar - (0÷4350 psi)
10 bar - (145 psi)
2100 l/min (*)
1
4
AC2
(*) Values measured at LP port with second stage connected and tank pressure at 200 150 bar (2900 2175 psi)
59
Direction for use regulators
SECOND STAGES
2.1 - Galaxy Adjustable /Master / Master Cromo / Galaxy /
Octopus MG Balanced
2.2 - Master / Master Cromo / Galaxy / Octopus MG Balanced
disassembly and maintenance
2.3 - XS Compact Pro / XS Compact
2.4 - XS Compact Pro / XS Compact, disassembly and servicing
2.5 - XS2
Loading...