ROLL-IN RETHERM HEAT-N-HOLD OVEN WITH RACK
MODEL RR-1332
FEATURES AND BENEFITS:
• Roll-In-Rack designed for moving school prepacked
meals in baskets from prep area, central kitchen,
commissary, or cooler into oven.
• Fully insulated Roll-In Retherm Heat-N-Hold oven
designed for rethermalizing school prepacked meals.
• Capable of rethermalizing prepacked food items from
40˚F. to 165˚F. in two hours or less (actual times may
vary).
• Full 8200 Watts of power provides maximum temperature
of 350˚F. (176.5˚C).
• Low volume convected air system and lower temperatures
help to maintain nutrition, flavor and moisture.
• Pre-setting automatic controls for rethermalizing and
holding cycles allows for unattended operation.
• Non-venting oven, permitted by most local codes,
provides easy, inexpensive installation.
• Capacity: 32 school baskets, 13" x 26".
• Highly accurate food probe, linked to the easy-to-use
and precise microprocessor digital controls, assures
consistent quality.
• Probe senses pre-set internal food temperature and
automatically switches to holding mode until ready to
serve.
• All welded stainless steel construction throughout for ease
of cleaning.
• Field reversible insulated door prevents temperature loss.
Silicone door gasket for proper seal. Latches and hinges
mounted inboard.
POWER UNIT OPTIONS:
8200 Watts, 208 Volts, 1 Phase, 60 Hz.
8200 Watts, 240 Volts, 1 Phase, 60 Hz.
8200 Watts, 208 Volts, 3 Phase, 60 Hz.
8200 Watts, 240 Volts, 3 Phase, 60 Hz.
JOB:
ITEM NO:
RR-1332
®
SANITATION
NSF/ANSI 4
C US
®
ACCESSORIES and OPTIONS
(Available at extra cost):
q Security Panel for Controls
q Key Lock Latch
q Wire Baskets
q Extra Roll-In Rack
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
Page E-6.2A
Oct., 2013
RR-1332
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
CABINET:
• Body: 22 ga. stainless steel.
• Inner liner: Formed 22 ga. stainless steel.
• Reinforcement: Internal framework of 14 ga. stainless steel channels, welded.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23 at 75˚F. 1-1/2" in back wall, door, base;
2" in side walls.
• Air tunnel: 20 ga. stainless steel, lift-out type, mounted on interior back panel.
• Vent: Adjustable.
BASE:
• One piece construction, .190 aluminum.
• Legs: Heavy duty polished stainless steel 2" O.D. adjustable for leveling oven.
DOOR:
• Field reversible.
• Formed 22 ga. stainless steel.
• Latch: Chrome plated high pressure die cast zinc, composite handle, ceramic magnetic.
• Hinges: Heavy duty chrome plated die cast zinc, mounted inboard.
• Door Gaskets: Perimeter type, silicone.
POWER UNIT COMPONENTS:
• Body: Formed 20 ga. stainless steel. Black control panel, tilted for ease of viewing.
• Microprocessor Control: Hold function: 140˚F. (60˚C.) to 250˚F. (121˚C.). Retherm/cook function:
140˚F. (60˚C.) to 350˚F. (176.5˚C.). 10 preset program buttons.
• Switch: Lighted ON-OFF rocker type.
• Power cord: Permanent, 6 ft., 6/3 ga. with right angle plug. Receptacle included.
• Heaters (3): 2670 Watts each.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 Amp.
POWER REQUIREMENTS AVAILABLE:
8200 Watts, 208 Volts, 1 Phase, 39 Amps., 50 Amp. Service.
8200 Watts, 240 Volts, 1 Phase, 34 Amps., 50 Amp. Service.
8200 Watts, 208 Volts, 3 Phase, 30 Amps., 30 Amp. Service.
8200 Watts, 240 Volts, 3 Phase, 20 Amps., 30 Amp. Service.
SHORT FORM SPECIFICATIONS
Cres Cor Roll-In Retherm Oven Model RR-1332.
Removable power unit 20 ga. stainless steel; recessed,
tilted control panel. Cabinet and door 22 ga., stainless
steel. Stainless steel internal frame. Fiberglass insulation
in sides 2”; back, doors and base 1-1/2”. One piece base
.190 aluminum. 2" dia. stainless steel legs. Includes
Cres Cor Roll-In Rack Model ROR-1332-SBS-R: 32
angles on 3" centers; holds 32 baskets. 5" swivel
modulus casters, Delrin bearings. 8200 Watts,
Volts, 60 Hz., Phase. 2 year parts
warranty. Provide the following accessories:
. CSA-US, CSA-C, CSA to NSF4 listed.
In line with its policy to continually improve its products,
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
© Crescent Metal Products, Inc. 2013 All rights reserved. Litho in U.S.A.
CRES COR reserves the right to change materials and
specications without notice.
Loading...