Cres Cor HJ-531-13-180 Installation Manual

Heated Dish

Dolly

FL-0508

5925 Heisley Road • Mentor, OH 44060-1833

OPERATING and MAINTENANCE INSTRUCTIONS

Models: HJ-531-10-240 and HJ-531-13-180

JETSTREAM HEATED DISH DOLLY

ELECTRICAL SPECIFICATIONS:

MODEL NO. Volts Watts Amps Hertz Phase Service

HJ-531-10-240
HJ-531-13-180

HJ-531-10-240-240
HJ-531-13-180-240

HOW TO INSTALL UNIT:

1. Plug cord into receptacle in back of unit.

2. Turn clockwise to lock.

3. Plug other end into 15 Amp wall outlet.

120 1000 8.4 60 1 AC

240 1000 4.2 60 1 AC

Rev. 22 (10/13) Page 1 of 2

MAINTENANCE:

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

HOW TO START UNIT:

1. Flip switch ON. Yellow light will come on.

2. Turn thermostat to #7 (150° F to 160° F / 66° C to
71° C) which will warm the plates.

3. Hint: Dial has a range of #1 to #10
(60° F to 250° F / 16° C to 121° C).

4. Pre-heat dolly for 30 minutes.

5. Add plates.

HOW TO TURN UNIT OFF:

Flip switch OFF.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE

PERSONNEL ONLY

REPLACEMENT PARTS

Description 120 Volt 240 Volt

Blower Kit 0769-180-K 0769-182-K
Cord Set 0810-031-1 0810-032-01
Heater Assembly 0811-074 0811-074-01
Receptacle 0713-011 0713-012
Red Light 0766-047 0766-046
Switch 0808-011 0808-020
Thermostat Kit 0848-062-K 0848-062-K
Yellow Light 0766-048 0766-045

Right Hand Left Hand

Door, HJ-531-10-240
Door, HJ-531-13-180
Door Latch, complete
Hinge

5686-011-K
5686-012-K
1246-015-K 1246-015-K
0519-018-K

5686-013-K
5686-014-K

0519-019-K

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Heated Dish

Dolly

FL-0508

Rev. 22 (10/13) Page 2 of 2

5925 Heisley Road • Mentor, OH 44060-1833

OPERATING and MAINTENANCE INSTRUCTIONS

Models: HJ-531-10-240 and HJ-531-13-180

JETSTREAM HEATED DISH DOLLY

TROUBLE-SHOOTING:

Failure Cause

1a. Cord not plugged into dolly or wall outlet.

1. Yellow light not on.

2. Unit does not get hot. 2a. Thermostat set too low.

3. Unit gets too hot or won’t shut off. 3a. Defective electrical parts; unplug cord from wall outlet.

If the cause is none of the above, refer to our list of Authorized Service Centers, FL-1400.

WARNING

BEFORE CLEANING CABINET:

1. Remove Power Cord from cabinet.

2. Do NOT hose cabinet with water.

3. Do NOT get water on controls.

4. Do NOT use abrasives or harsh chemicals.

1b. Circuit breaker/fuse to wall outlet blown.
1c. Switch is off.

Cleaning Hints:

1. Wipe up spills as soon as possible.

2. Clean regularly to avoid heavy dirt build-up.

3. Make a test spot with cleaner.

4. Follow manufacturer’s directions on cleaner.

5. Do not mix cleaners.

6. Avoid drips and splashes.

Dolly

Inside and Outside

(Aluminum)

LEGEND

SW SWITCH (SPST)
BM BLOWER MOTOR
TH THERMOSTAT
H HEATER
A AMBER PILOT LIGHT
R RED PILOT LIGHT
L5-15R RECEPTACLE, 110V/15A
L6-15R RECEPTACLE, 220V/15A

ELECTRICAL SPEC

120/240V 1000W
1 PHASE 60 HZ
AC SERVICE

SOIL CLEANER METHOD

Mild detergent* and hot water, or mild

DIRT

FINGERPRINTS,
GREASE OIL

WATER SPOTS Mild abrasive cleaner. Wipe with damp cloth.

* Mild detergents include soaps and non-abrasive cleaners

abrasive cleaner.

Steam (no strong alkaline additive)

Detergent* and hot water.

Mild abrasive cleaner.
Oily or waxy cleaner.

1. Use soft, damp cloth.

2. Rinse with hot water.

3. Wipe dry.

1. Rinse after steam cleaning.

2. Wipe dry.

1. Wipe with soft, damp cloth.

2. Rinse with hot water.

3. Wipe dry.

Apply with soft, clean cloth.

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com