Cres Cor HJ-531-10-240 Service Manual
5925 Heisley Road • Mentor, OH 44060-1833
®
®
OPERATING and MAINTENANCE INSTRUCTIONS
Models: HJ-531-10-240 and HJ-531-13-180
JETSTREAM HEATED DISH DOLLY
ELECTRICAL SPECIFICATIONS:
MODEL NO. Volts Watts Amps Hertz Phase Service
HJ-531-10-240
HJ-531-13-180
HJ-531-10-240-240
HJ-531-13-180-240
120 1060 8.8 60 1 AC
240 1060 4.4 60 1 AC
Heated
Dish Dolly
Rev. 18 (5/06) Page 1 of 2
NSF/ANSI 4
FL-0508
C US
HOW TO INSTALL UNIT:
Plug cord into receptacle in back of unit.
1.
Turn clockwise to lock.
2.
Plug other end into 15 Amp wall outlet.
3.
HOW TO START UNIT:
Flip switch ON. Yellow light will come on.
1.
Turn thermostat to #7 (150° F to 160° F / 66° C to
2.
71° C) which will warm the plates.
Hint: Dial has a range of #1 to #10
3.
(60° F to 250° F / 16° C to 121° C).
4. Pre-heat dolly for 30 minutes.
5. Add plates.
HOW TO TURN UNIT OFF:
Flip switch OFF.
MAINTENANCE:
REPLACEMENT PARTS
Description 120 Volt 240 Volt
Heater Ass’y 0811-074 0811-074-01
Blower Kit 0769-005-K 0769-006-K1
Thermostat Kit 0848-062-K 0848-062-K
Yellow Light 0766-048 0766-045
Red Light 0766-047 0766-046
Receptacle 0713-011 0713-012
Cord Set 0810-031-01 0810-032-01
Switch 0808-011 0808-020
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Heated
Dish Dolly
FL-0508
Rev. 18 (5/06) Page 2 of 2
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
Models: HJ-531-10-240 and HJ-531-13-180
JETSTREAM HEATED DISH DOLLY
TROUBLE-SHOOTING:
Failure Cause
1a. Cord not plugged into dolly or wall outlet.
1. Yellow light not on.
2. Unit does not get hot. 2a. Thermostat set too low.
3. Unit gets too hot or won’t shut off. 3a. Defective electrical parts; unplug cord from wall outlet.
If the cause is none of the above, refer to our list of Authorized Service Centers, FL-1400.
BEFORE CLEANING CABINET:
1. Remove Power Cord from cabinet.
2. Do NOT hose cabinet with water.
3. Do NOT get water on controls.
4. Do NOT use abrasives or harsh chemicals.
1b. Circuit breaker/fuse to wall outlet blown.
1c. Switch is off.
Cleaning Hints:
Wipe up spills as soon as possible.
1.
Clean regularly to avoid heavy dirt build-up.
2.
Make a test spot with cleaner.
3.
Follow manufacturer’s directions on cleaner.
4.
Do not mix cleaners.
5.
Avoid drips and splashes.
6.
Dolly
Inside and Outside
(Aluminum)
LEGEND
SW SWITCH (SPST)
BM BLOWER MOTOR
TH THERMOSTAT
H HEATER
A AMBER PILOT LIGHT
R RED PILOT LIGHT
L5-15R RECEPTACLE, 110V/15A
L6-15R RECEPTACLE, 220V/15A
ELECTRICAL SPEC
120/240V 1000W
1 PHASE 60 HZ
AC SERVICE
SOIL CLEANER METHOD
Mild detergent* and hot water, or mild
DIRT
FINGERPRINTS,
GREASE OIL
WATER SPOTS Mild abrasive cleaner. Wipe with damp cloth.
abrasive cleaner.
Steam (no strong alkaline additive)
Detergent* and hot water.
Mild abrasive cleaner.
Oily or waxy cleaner.
1. Use soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
1. Rinse after steam cleaning.
2. Wipe dry.
1. Wipe with soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
Apply with soft, clean cloth.
* Mild detergents include soaps and non-abrasive cleaners
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Loading...