Cres Cor HC1-UA-11 Installation Manual

Holding Cabinet

WARNING

FL-2387

5925 Heisley Road • Mentor, OH 44060-1833

OPERATING and MAINTENANCE INSTRUCTIONS

Model: HC1-UA-11 Hot Cabinet

Rev. 1 (07/15) Page 1 of 8

Cabinet model number:

Cabinet serial number:

Authorized Service Agency:

Ph: Fax:

Keep this manual for future reference.

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

HC1-UA-11

IMPROPER INSTALLATION, SERVICE,
ADJUSTMENTS, ALTERATIONS CAN
CAUSE PROPERTY DAMAGE, INJURY
OR DEATH. READ THE INSTALLATION
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.

Holding Cabinet

FL-2387

Rev. 1 (07/15) Page 2 of 8

5925 Heisley Road • Mentor, OH 44060-1833

TABLE OF CONTENTS

SUBJECT PAGE

INSTALLATION INSTRUCTIONS .............................................3

OPERATING INSTRUCTIONS ................................................6

Illustration, Figure 1 ..........................................................6

MAINTENANCE INSTRUCTIONS

How to Clean the Unit ...................................................7

Trouble Shooting Guide and Wiring Diagram .................................8

Illustration; Cabinet assembly replacement parts ...............................9

SERVICE POLICY and AGENCY LIST ....................................FL-1400

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE

PERSONNEL ONLY

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Holding Cabinet

FL-2387

5925 Heisley Road • Mentor, OH 44060-1833

Rev. 1 (07/15) Page 3 of 8

INSTALLATION INSTRUCTIONS

INSTRUCTIONS TO INSTALLER BEFORE CONNECTING TO GAS SUPPLIES

1. Retain this manual for further use.

2. Post in a prominent place the following instructions:

FOR YOUR SAFETY

FOR YOUR SAFETY

IF YOU SMELL GAS:

1. Extinguish any open ame.

2. Immediately remove propane tank,
shut off gas supply or call your gas
supplier.

Do not store or use gasoline

or other ammable vapors

and liquids in the vicinity of

this or any other appliance.

3. Installation in the United States must conform with the local codes, or in the absence of local codes, with
the NFPA 54/ANSI Z223.1 2012. Installation in Canada must comply with the Installation codes for Gas
Burning Appliances and Equipment, CAN/CSA B149.1-10 and/or local codes.

4. The area around cabinet must be kept free and clear from combustible materials.

5. DO NOT obstruct the ow of combustion and ventilation air. DO NOT block slots or louvers on front and
rear of unit in any way.

6. Provisions for adequate air supply, in cabinet area, must be provided.

7. Adequate clearances for servicing and proper operation must be provided.

8. CLEARANCE FROM COMBUSTIBLE CONSTRUCTION, 0 INCHES FROM SIDE AND 0 INCHES
FROM BACK.

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Holding Cabinet

WARNING

FL-2387

Rev. 1 (07/15) Page 4 of 8

INSTALLATION INSTRUCTIONS

HC1-UA-11 FOR PROPANE CYLINDER
INSTALLATION:

This cabinet is

not intended

for use with natural gas. It is not user­convertible to natural gas.

1. Only use a 1 lb. standard cylinder marked
“PROPANE”. A larger tank can be used with an
adapter (optional accessory part number 0904-026-K
See installation FL-2362).

2. The cylinder must be constructed and marked in

accordance with the specications for propane

cylinders of the U.S. Department of Transportation
(DOT) or CAN/CSA B339.

3. The Cylinder should not be allowed to remain in a
high heat area, such as a car, truck or direct sunlight.

DO NOT store at temperatures above 120°F (49° C)

and in unauthorized storage areas not intended for
cylinder storage.

5925 Heisley Road • Mentor, OH 44060-1833

GENERAL INSTALLATION:

1. Remove all paper and packing materials from the
inside of the cabinet and install angles into posts.

2. Remove protective paper and vinyl material from
the outside of the cabinet.

3. Place the cabinet in a well-ventilated area on level

oor or ground.

4. DO NOT block the ue vent located at the upper
rear of the cabinet.

5. Lock the two front casters before starting up or
plugging in the cabinet.

HOW TO INSTALL ANGLES:

1. Insert end tabs of the angles into the post slots
and push down.

2. Note the location shown in the diagram of the
18” x 26” pan slide and the 12” x 20” pan slide

18” X 26” BUN PAN

4. Hold and use the cylinder in an upright position and

only use when temperatures are above 10°F (-12° C).
Do not attach near ames, pilot lights or sparks.

5. Propane Tank Hook-up:

a. Make sure the gas valve is in the “OFF” position.

b. Uncap the cylinder, hold upright and insert it in the
right rear compartment of the cabinet. Hand screw
and tighten the cylinder to the gas regulator. DO

NOT over-tighten.

Check for leaks at the connection: Spray soapy water
onto the connection and look for bubbles. Tighten more if
needed.

6. Disconnect the cylinder when not in use. Replace the
cylinder cap when storing.

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

12” X 20”
STEAM TABLE PAN

Holding Cabinet

FL-2387

5925 Heisley Road • Mentor, OH 44060-1833

OPERATING INSTRUCTIONS

HOW TO HOLD FOOD:

Air is VERY HOT

WARNING

PROCEDURE FOR LIGHTING:

NOTE: DO NOT PUT FOOD INTO CABINET!
This step is to burn off manufacturing oils and excess

adhesive. Let the cabinet cool and wipe inside clean
with detergent and hot water before rst use.

Dials must be operated by hand. DO NOT use pliers,
wrenches or other tools to turn dials.

The Gas Valve Dial cannot be turned to “OFF” position
without rst depressing dial in “PILOT” position and then

rotating to “OFF”.

when door is opened.

Rev. 1 (07/15) Page 5 of 8

NOTE: When unit is not in use, ALWAY S store unit with

the Gas Valve Dial in the “OFF” position. Remove

the propane source for added safety and turn the
thermostat to the “OFF” position.

1. Turn thermostat knob to “HIGH”.

2. Turn Gas Valve Dial to the “PILOT” position.

3. DEPRESS and HOLD Gas Valve Dial, allow pilot to
burn approximately 30 seconds before RELEASING

Gas Valve Dial. If pilot does not remain lighted, repeat

operation allowing longer period before releasing Gas

Valve Dial.

4. The appliance is now in operation. When heat is

desired, turn Gas Valve Dial to “ON” position. When
heat is no longer required, turn Gas Valve Dial back to

“PILOT” position.

5. When the unit is in the “ON” position adjust the ther­mostat accordingly (“High”, “Medium”, “Low”).

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Holding Cabinet

WARNING

FL-2387

Rev. 1 (07/15) Page 6 of 8

MAINTENANCE INSTRUCTIONS

BEFORE cleaning the cabinet,
allow cabinet to cool.

CAUTION

1. Do NOT use abrasives (steel wool) or harsh
chemicals (chlorine, bromine, iodine or ammonia).

2. Do NOT use a water sprayer (pressure sprayer) to
clean the cabinet.

3. Do not use Cres Clean on label or plastic
materials.

5925 Heisley Road • Mentor, OH 44060-1833

Cleaning hints:

1. Wipe up spills as soon as possible.

2. Clean cabinet daily to avoid heavy dirt build-up.

3. Make a test spot with cleaner:
a) Follow manufacturer’s directions on cleaner.
b) Do not mix cleaners.

c) Avoid drips and splashes.

HOW TO CLEAN THE UNIT:

Soil Cleaner Method

OUTER CABINET

(Powder Coat)

CABINET

Inside and

Door

(Stainless Steel)

WEEKLY, OR AS NEEDED

DAILY CLEANING

STUBBORN SPOTS AND
STAINS

BURNT-ON FOODS OR
GREASE

HARD WATER SPOTS
and SCALE

*Mild detergents include soaps and non-abrasive cleaners.

Mild detergent and warm
water.

Mild detergent and hot
water.

Mild abrasive made for
stainless steel.

Chemical oven cleaner for
stainless steel.

Vinegar

1. Wipe with clean, soft cloth.

2. Rinse well.

3. Dry gently.

1. Sponge on with cloth.

2. Rinse with water.

3. Wipe dry.

1. Apply with damp sponge or cloth.

2. Rub lightly.

3. Rinse with water and wipe dry.

Follow oven cleaner manufacturer’s
directions.

1. Swab or wipe with cloth.

2. Rinse and dry.

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Holding Cabinet

FL-2387

5925 Heisley Road • Mentor, OH 44060-1833

Rev. 1 (07/15) Page 7 of 8

TROUBLE-SHOOTING

FAILURE POSSIBLE CAUSE

1. Unit does not turn on. 1a. Battery is low on charge.
1b. Gas tank is empty.

2. Unit heats up slowly. 2a. Check operating instructions for preheat times.

2b. Defective components.

3. Unit does not heat. 3a. Unit is not on.
3b. Thermostat is set too low.
3c. Propane/gas tank has expired.

3d. A gust of wind may have blown out the ame or

prevented ignition of the gas.

4. Unit gets too hot or won’t shut off. 4. Defective thermostat.

For repairs, refer to our list of Authorized Service Centers, FL-1400

NOTE: If any panel which is sealed with silicone needs to be removed for servicing by an authorized personnel,

the exterior seams need to be sealed with a food grade caulking material (certied against NSF/ANSI 51).

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com

Holding Cabinet

FL-2387

Rev. 1 (07/15) Page 8 of 8

Include all information on nameplate when ordering parts

3

5925 Heisley Road • Mentor, OH 44060-1833

REPLACEMENT PARTS

2

3

1

4

PROPANE TANK
HOOK-UP AREA

12 13

16

9

11

10

8

5

6

ITEM DESCRIPTION 120V

1 Door Assembly 1221-649
2 Hinge (2 per kit) 0519-110-K
3 Latch 1006-143-K
4 Gasket, Door 0861-182-K
5 Casters, Rigid 0569-341-R
6 Casters, w/Brake 0569-341-B
7 Wire Angles (2 per kit) 0621-352-K
8 Sight Glass 0574-167

9 Regulator 8100-009
10 Battery 9V 7037-010
11 Igniter 8100-027
12 Thermostat 0848-062
13 Knob 0595-001
14 Burner 8100-002-01
15 Pilot Ass’y 8100-029
16 Gas Valve 8100-025

15

14

UNDERNEATH CABINET SHOWN WITH

BASE & COVERS REMOVED

8100-025-A KNOB

ITEM #16, GAS VALVE

MICRO-SWITCH
0808-127

ASSEMBLY

8100-025

Call Toll-free: 877-CRES COR (273-7267) • Fax: [phone] • www.crescor.com