Page 1
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
FOR HOLDING CABINET
ELECTRICAL SPECIFICATIONS:
MODEL Volts Watts Amps Hertz Phase NEMA
H-339-1813C-GMR
H-339-1813C-GML
120 900 7.5 60 1 5-15
Insulated
Holding Cabinet
Rev. 7 (4/06) Page 1 of 4
FL-0520-3
HOW TO INSTALL UNIT:
Plug cord into 15-Amp wall outlet.
1.
Place cabinet in a well ventilated area.
2.
Hang wire racks inside the cabinet.
3.
Push the switch on, turn the thermostat to No. 10
4.
and run the unit for one hour.
NOTE: DO NOT PUT IN FOOD! This step is to
burn off manufacturing oils and excessive
adhesive.
6. Let the cabinet cool and wipe inside clean with
detergent and hot water before use.
FIGURE 1
HOW TO OPERATE UNIT: (Figure 1)
1.
2.
NOTE: No. 7½ setting will give you about 180° F
3. Preheat cabinet for 45 minutes
4. Put food into cabinet.
5. Turn the wing nut on the door vent to open the vent
To Turn Off Unit:
Push switch “OFF”. The yellow light will go off.
NOTE: Optional digital thermometer will fl ash if cabinet
Push switch “ON”. Yellow light will come on.
Turn thermostat to the temperature you need.
(82°C). Proper food holding temperature is
140° F (60°C) or higher.
when less humidity is needed.
temperature is below 140°F or above 250°F.
Call the factory if you need different settings.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Page 2
Insulated
Holding Cabinet
Rev. 7 (3/06) Page 2 of 4
FL-0520-3
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION INSTRUCTIONS
FOR HOLDING CABINET
BEFORE CLEANING CABINET:
1. Unplug power cord from wall.
2. Do NOT hose cabinet with water.
3. Do NOT get water on controls.
4. Do NOT use abrasives or harsh
chemicals.
HOW TO CLEAN UNIT:
SOIL CLEANER METHOD
DIRT
CABINET
Inside and
Outside
(Aluminum)
FINGERPRINTS,
GREASE OIL
Hints:
Wipe up spills as soon as possible.
1.
Clean cabinet regularly to avoid heavy dirt build-up.
2.
Make a test spot with cleaner.
3.
Follow manufacturer’s directions on cleaner.
4.
Do not mix cleaners
5.
Avoid drips and splashes.
6.
Mild detergent* and hot water,
or mild abrasive cleaner.
Steam (no strong alkaline
additive)
Detergent* and hot water.
Chemical oven cleaner for
aluminum.
Mild abrasive cleaner.
Oily or waxy cleaner.
1. Use soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
1. Rinse after steam cleaning.
2. Wipe dry.
1. Wipe with soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
Follow oven cleaner manufacturer’s
directions.
Apply with soft, clean cloth.
WATER SPOTS Mild abrasive cleaner. Wipe with damp cloth.
* Mild detergents include soaps and non-abrasive cleaners
HOW TO ADJUST THE DOOR LATCH:
1. For vertical adjustment
(Up and down movement):
a. Loosen (2) screws located in magnetic
strike on cabinet.
b. Move strike up or down for alignment
to magnet on latch.
c. Tighten screws to secure
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
2. For horizontal adjustment
(Greater or lesser magnetic draw):
a. Loosen four (4) screws in latch on door.
b. Move latch forward or backward to
adjust magnetic draw.
c. Tighten screws to secure.
Page 3
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION INSTRUCTIONS
FOR HOLDING CABINET
HOW TO REVERSE DOOR HARDWARE
FOR OPPOSITE HAND (Refer to Fig. 3 [hinge]):
Pop off hinge covers with screwdriver.
1.
Remove screws from hinges to cabinet; remove door
2.
and unscrew latch strike from cabinet.
Remove hinges, latch and all remaining screws from
3.
the right and left side of door. Keep all screws.
Re-mount hinges and latch in the same hole pattern on
4.
the opposite sides of the door. Plug all extra holes with
screws.
Remove all screws from the front sides of cabinet (not
5.
the top and bottom).
Hold door up to cabinet and screw hinges to the
6.
cabinet.
Open door and re-mount the latch strike to cabinet.
7.
Plug all extra holes with screws and snap on the hinge
8.
covers.
Insulated
Holding Cabinet
Rev. 7 (4/06) Page 3 of 4
FIGURE 2
FL-0520-3
REPLACEMENT PARTS:
DESCRIPTION CMP PART#
Cord Set......................................................0810-029
Switch.........................................................0808-113
Heater Kit....................................................0811-066-K
Thermostat Kit............................................0848-062-K
Terminal Block...........................................0852-091
Thermometer...............................................5238-030
Door Latch Kit............................................1006-122-01-K
Strike Kit.....................................................1006-122-02-K
Hinge Kit.................................................... 0519-074-K
Gasket Kit...................................................0861-077
Casters, 2” dia. ...........................................0569-286
Door Replacement Kit................................5508-084
Rack Insert..................................................1137-130-03
TROUBLE-SHOOTING CHART
FAILURE POSSIBLE CAUSE/CHECK
1. Unit does not heat: 1a. Thermostat turned up.
1b. Switch is “ON”.
1c. Cord is plugged into outlet.
1d. Circuit breaker/fuse for
wall outlet
2. Unit will not turn off: 2a. Thermostat turned down.
2b. Switch is “OFF”
If cause is none of the above, refer to our list of
authorized service agencies, FL-1400.
Instructions for replacing parts are
included in replacement parts kits.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Page 4
Insulated
Holding Cabinet
Rev. 7 (3/06) Page 4 of 4
FL-0520-3
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION INSTRUCTIONS
FOR HOLDING CABINET
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Loading...