®
®
®
ROAST-N-HOLD™
®
®
GENTLE CONVECTION OVEN
MODEL CO-151-FUA-12B
FEATURES AND BENEFITS:
• Fully insulated Roast-N-Hold gentle convection oven
• designed for flavorful results by slow roasting.
• Slow convected air system promotes natural browning
• for flavor and seals in natural juices. Slow roasting means
• 15% to 20% less shrinkage.
• Full 8200 Watts of power allows for reheating of prepared
• meals or bulk items. Maximum temperature 350˚F. (176.5˚C.).
• Pre-setting automatic controls for roasting and holding
• cycles allows for unattended operation 24 hours a day.
• Roast and hold over 300 lbs. (136 kg.) of meat in just
• 7 sq. ft. of floor space.
• Non-venting oven, permitted by most local codes, provides easy,
inexpensive installation.
• Self-contained power top lifts off for ease of maintenance;
• available to suit your power requirements.
• 304 stainless steel construction throughout for ease of cleaning.
• Smooth interior coved corners prevent food particle/grease buildup.
• Field reversible insulated Dutch doors prevent temperature •
• loss. Silicone door gaskets for proper seal. High temperature
ceramic magnetic latches for “easy open” and security during
• transport. Latches and hinges mounted inboard.
• Standard with right hand hinging; left hand hinging available
upon request.
• Recessed push/pull handles on both sides prevent damage
• to walls; allows easy maneuvering.
• Chrome plated wire universal angles accommodate a large
variety of pan sizes on adjustable 1-1/2" spacing. Supplied
with 12 sets of angles and six raised wire grids.
• Heavy duty 5" swivel casters, two with brakes. Provides
mobility when fully loaded.
•
• Free cooking manual and operation manual provided
• with the purchase of any Roast-N-Hold Oven.
POWER UNIT OPTIONS:
• 8200 Watts, 208 Volts, 1 Phase, 60 Hz.
• 8200 Watts, 240 Volts, 1 Phase, 60 Hz.
• 8200 Watts, 208 Volts, 3 Phase, 60 Hz.
• 8200 Watts, 240 Volts, 3 Phase, 60 Hz.
Probe Power Unit Available at Extra Cost (see page E-6)
JOB:
ITEM NO:
CO-151-FUA-12B
SANITATION
CLASSIFIED
CLASSIFIED TO
NSF4
C
ACCESSORIES and OPTIONS
(Available at extra cost):
Security Panel for Controls
Tempered Glass Door Windows
Key Lock Latches
Extra Wire Grids
Extra Universal Angles
Perimeter Bumper
Corner Bumpers
Floor Lock (for use with 5” casters)
Various Caster Options
50 Cycle Service
380 Volts, 3 Phase
See page E-10 for accessory details.
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
Page E-1
Sept., 2004
®
CO-151-FUA-12B
DETAIL OF
PAN SLIDE
CRES COR PAN DIM “A” DIM “B” DIM “C” INSIDE DIMENSIONS WEIGHT
MODEL NO.
CO-151-FUA-12B
NOTE: Refer to pan size chart at end of section.
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
CABINET:
• Body: 22 ga. 304 stainless steel.
• Reinforcement: Internal framework of 16 ga. stainless steel.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23
• at 75˚F. 1-1/2" in back wall, doors, base; 2" in side walls.
• Air tunnel: 20 ga. stainless steel, lift-out type, mounted
• on rear wall.
• Push/pull handles (2): 7" vertical; recessed.
BASE:
• One piece construction, .125 aluminum.
• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.
• 250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front
casters equipped with brakes.
DUTCH DOORS:
• Field reversible.
• Formed 22 ga. 304 stainless steel.
• Latches: Chrome plated steel, high temperature ceramic
• magnetic type; mounted inboard.
• Hinges: Heavy duty chrome plated steel, lift-off type; mounted
• inboard.
• Gaskets: Perimeter type, silicone.
• Pan stops: Embossed.
PAN SLIDES:
• Wire angles (.306 dia.), nickel chrome plated steel;
mounted on lift-out posts.
•
• 12 sets of angles adjustable on 1-1/2" centers.
• Grids (6): Nickel chrome plated steel, raised wire 17" x 25".
POWER REQUIREMENTS AVAILABLE:
• 8200 Watts, 208 Volts, 60 Hz., 1 phase, 39 Amps.,
50 Amp. service.
•
• 8200 Watts, 240 Volts, 60 Hz., 1 phase, 34 Amps.,
50 Amp. service.
•
• 8200 Watts, 208 Volts, 60 Hz., 3 phase, 23 Amps.,
30 Amp. service.
•
• 8200 Watts, 240 Volts, 60 Hz., 3 phase, 20 Amps.,
30 Amp. service.
•
CAP/ANGLES
12 SEE N O T E IN 28-3/4 37-3/4 73-1/2 21-1/4 26-1/2 58 LBS 378
SETS BELOW MM 740 960 1870 540 675 1475 KG 171
SIZE WIDTH DEPTH HEIGHT WIDTH DEPTH HEIGHT ACT.
POWER UNIT COMPONENTS: (refer to above drawing)
• Body: Formed 20 ga. 304 stainless steel with black control
• panel, recessed and tilted 7˚.
A) Thermostat (holding): Solid state, room ambient to 250˚F. (121˚C.).
B) Thermostat (cook/retherm): Solid state, room ambient to 350˚F.
(176.5˚C.).
C) Pilot lights (2).
D) Switch: Lighted ON-OFF rocker type.
E) Timer: 24 hr. digital countdown; infinite memory retention.
F) Thermometer.
• Power cord: Permanent, 6 ft., 6/3 ga. with right angle plug.
• Heaters (3): 2670 Watts each.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 Amp.
INSTALLATION REQUIREMENTS:
• Check local vent hood codes for mobile Roast-N-Hold ovens.
SHORT FORM SPECIFICATIONS
Cres Cor Roast-N-Hold Convection Oven Model
CO-151-FUA-12B. Removable power unit 20 ga. 304
stainless steel, recessed control panel. Cabinet and Dutch
doors 22 ga. 304 stainless steel; stainless steel internal
frame; coved corner interior. Fiberglass insulation in sides
2”; back, doors and base 1-1/2”. High temperature magnetic
latches. (12) sets universal angles for multiple pan sizes and
spacing. One piece base .125 aluminum. 5" swivel modulus
casters, Delrin bearings. Load capacity 250 lbs. each.
8200 Watts,
parts warranty. Provide the following accessories:
___ ___ ___UL Sanitation, UL, CUL listed.
Volts, 60 Hz., Phase. 2 year
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
© Crescent Metal Products, Inc. 1998 All rights reserved.
In line with its policy to continually improve its products,
CRES COR reserves the right to change materials and
specifications without notice.
Litho in U.S.A.
Loading...