Cres Cor H-339- 128C-240, 188C-240, 12-188C-240, 1813C-240, UA-8C-240 User Manual
Insulated
Hand-lift Cabinet
Rev. 38 (4/13) Page 1 of 4
FL-0520
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
For INSULATED HAND-LIFT CABINETS; MODEL H-339 “C” SERIES
ELECTRICAL SPECIFICATIONS:
MODEL Volts Watts Amps Hertz Phase NEMA
H-339 -128C, 188C,
12-188C, 1813-C,
UA-8C, 12-135C
H-339- 128C-240, 188C-240,
12-188C-240, 1813C-240,
UA-8C-240, 12-135C
Above model numbers may include letters: M, L, P, S, SS or Z.
120 900 7.5 60 1 5-15
240 900 3.8 60 1 6-15
FIGURE 1 FIGURE 2
HOW TO INSTALL UNIT: (Figure 1)
1. Plug cord into receptacle in back of the unit.
2. Turn plug clockwise to lock.
3. Plug other end into 15-amp wall outlet.
4. Place cabinet in a well ventilated area.
5. Push the switch on, turn the thermostat to No. 10
and run the unit for one hour.
NOTE: DO NOT PUT IN FOOD! This step is to
burn off manufacturing oils and excessive
adhesive.
6. Let the cabinet cool and wipe inside clean with
detergent and hot water before use.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
HOW TO OPERATE UNIT: (Figure 2)
1. Push switch “ON”. Yellow light will come on.
2. Turn thermostat to the temperature you need.
NOTE: No. 7½ setting will give you about 180° F
(82°C). Proper food holding temperature is
140° F (60°C) or higher.
3. Preheat cabinet for 45 minutes
4. Put food into cabinet.
5. Turn the wing nut on the door vent to open the vent
when less humidity is needed.
To Turn Off Unit:
Push switch “OFF”. The yellow light will go off.
NOTE: Optional digital thermometer will ash if cabinet
temperature is below 140°F or above 250°F.
Call the factory if you need different settings.
Insulated
WARNING
Hand-lift Cabinet
Rev. 38 (4/13) Page 2 of 4
FL-0520
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
For INSULATED HAND-LIFT CABINETS; MODEL H-339 “C” SERIES
Hints:
BEFORE CLEANING CABINET:
1. Remove Power Cord from cabinet.
2. Do NOT hose cabinet with water.
3. Do NOT get water on controls.
4. Do NOT use abrasives or harsh
chemicals.
HOW TO CLEAN UNIT:
SOIL CLEANER METHOD
DIRT
CABINET
Inside and
Outside
FINGERPRINTS,
GREASE OIL
Mild detergent* and hot water,
or mild abrasive cleaner.
Steam (no strong alkaline
additive)
Detergent* and hot water.
Chemical oven cleaner.
Mild abrasive cleaner.
Oily or waxy cleaner.
1. Wipe up spills as soon as possible.
2. Clean cabinet regularly to avoid heavy dirt build-up.
3. Make a test spot with cleaner.
4. Follow manufacturer’s directions on cleaner.
5. Do not mix cleaners
6. Avoid drips and splashes.
7. Do not use Cres Clean on plastics and labels.
1. Use soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
1. Rinse after steam cleaning.
2. Wipe dry.
1. Wipe with soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
Follow oven cleaner manufacturer’s
directions.
Apply with soft, clean cloth.
WATER SPOTS Mild abrasive cleaner. Wipe with damp cloth.
* Mild detergents include soaps and non-abrasive cleaners
HOW TO REVERSE DOOR HARDWARE
FOR OPPOSITE HAND (Refer to Fig. 3 [hinge]):
1. Pop off hinge covers with screwdriver.
2. Remove screws from hinges to cabinet; remove door
and unscrew latch strike from cabinet.
3. Remove hinges, latch and all remaining screws from
the right and left side of door. Keep all screws.
4. Re-mount hinges and latch in the same hole pattern on
the opposite sides of the door. Plug all extra holes with
screws.
5. Remove all screws from the front sides of cabinet (not
the top and bottom).
6. Hold door up to cabinet and screw hinges to the
cabinet.
7. Open door and re-mount the latch strike to cabinet.
8. Plug all extra holes with screws and snap on the hinge
covers.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
C'SK SCREWS
#10-24 X 3/4"
DOOR
TOP
FIGURE 3
CABINET
BODY
SCREWS-T.H.M
#10-24 X 1/2"
HINGE
COVER
Loading...