Cres Cor 131-UA-11D User Manual

NON-INSULATED

HOT CABINETS

131-UA SERIES

FEATURES AND BENEFITS:

• Non-Insulated hot cabinet to keep prepared
foods at serving temperatures.

• Powerful, yet efcient, heating system maintains
the right temperature to properly hold products.

2000 Watt cabinet holds foods at up to 180˚F
(82˚C).

• Body constructed of non-corrosive, Hi-Tensile
aluminum with extruded frame fully welded for
strength and ease of mobility.

JOB:

ITEM NO:

• Perimeter door gasket minimizes heat loss.

• Reinforced, eld reversible brushed aluminum

door for exibility. Standard with right hand

hinging; left hand hinging available upon
request.

• Safety-conscious anti-microbial latch protect
against spreading germs.

• Magnetic type latch secures door during
transport.

• Wire universal angles accommodate a large
variety of pan sizes on adjustable 1-1/2" centers.

• Controls accessible without opening door; allows
adjustments without interrupting process.

• Slanted control panel has easy-to-read
thermometer; entire assembly removable for
cleaning and maintenance.

• Heavy duty 5" swivel casters, two with brakes.
Provides mobility when fully loaded.

131-UA-11D

®

SANITATION

NSF/ANSI 4

ACCESSORIES and OPTIONS
(Available at extra cost):

q Lock Hasp

q Lexan Door

q Extra Universal Angles

q Dutch Doors (131UA11D Only)

q Corner Bumpers

q Perimeter Bumper (three sided)

q Push Handle

q Various Caster Options

q Digital Thermometer

q 208 or 240 Volt Service

See page B-20 for accessory details.

C US

®

5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: [phone]
www.crescor.com

Page B-3

Oct., 2014

4-1/2

131-UA Series

12-15/166-3/16

BAA

B

C

9-1/2

DETAIL OF
PAN SLIDE

CRES COR

MODEL NO.

ANGLES

131-UA-9D

131-UA-11D

NOTES: 1. Pan sizes 22" x 20" (560 x 510) Roast & Bake Pans, 10" x 20" (255 x 510) Roast & Bake Pans, 18" x 26" (460 x 660)

ALL ALUMINUM CONSTRUCTION IS RIVETED, WELDED AND FINISHED.

Bun Pans, 14" x 18" (355 x 460) Service Trays, 12" x 20" (305 x 510) Steam Table Pans.
Refer to Pan Size Chart at end of section.

2. When ordering bumpers, add 2" to overall dimensions.

CABINET:

• Top: One piece .063 aluminum; riveted to sides and back.

• Side panels: Formed .063 aluminum; fastened to base and top.

• Back: .063 aluminum; fastened to base and top.

• Air tunnel: .063 aluminum; lift-out type, mounted to the back
panel.

BASE:

• One piece construction, .125 aluminum.

• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.

250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front

casters equipped with brakes.

PAN DIM "A" DIM "B" DIM "C" INSIDE DIMENSIONS

CAP/

9

SETS

11

SETS

SIZE WIDTH DEPTH HEIGHT WIDTH DEPTH HEIGHT

SEE NOTE

BELOW

SEE NOTE

BELOW

IN 24-1/4 32 57-3/4 21-1/4 28-1/4 42-3/8 LBS 173

MM 620 815 1470 540 718 1080 KG 78

IN 24-1/4 32 69-3/4 21-1/4 28-1/4 54-3/8 LBS 198

MM 620 815 1775 540 718 1385 KG 90

HOT UNIT COMPONENTS (CONT.):

• Thermostat: Mechanical, room ambient to 180˚F (82˚C).

• Switch: ON-OFF rocker type.

• Power light

• Power cord: Permanent, 6 ft., 12/3 ga. with molded plug.

• Heater: 1850 Watts.

• Blower motor.

• Thermometer.

POWER REQUIREMENTS:

• 2000 Watts, 120 Volts, 60 Hz., single phase, 16.7 Amps.,
20 Amp. service.

DOOR:

• Field reversible.

• Panel: .063 brushed aluminum, tted into door frame extrusions,

13/16 x 1-11/16 x .154; Black powder coated.

• Latch: Chrome plated steel, magnetic type; mounted inboard

• Hinges (2): Chrome plated steel.

• Gasket: Perimeter type, Santoprene rubber.

PAN SLIDES:

• Wire angles, (.306 dia.) nickel chrome plated steel, mounted on

lift-out posts.

• Spaced on 4-1/2" centers; adjustable on 1-1/2" centers.

HOT UNIT COMPONENTS:

• Removable bottom mount hot unit.

• Body: Formed .063 aluminum with black control panel.

Cres Cor Hot Cabinet Model 131-UA- D. Formed
and welded .063 aluminum top, .125 aluminum base.
(____) sets extruded universal angles for multiple pan
sizes, adjustable spacing every 1-1/2". Brushed .063
aluminum door. Removable 2000 Watt, 120 Volt power

unit. Controls accessible without opening door. 5" swivel

modulus casters, Delrin bearings. Load capacity 250 lbs.
each. 1-Year Parts / 90-Day Labor warranty. Provide

the following accessories: ____ _____ _____ CSA­US, CSA-C, CSA to NSF4 listed.

SHORT FORM SPECIFICATIONS

W

5-20P

WEIGHT

ACT.

G

In line with its policy to continually improve its products,

5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: [phone]
www.crescor.com

© Crescent Metal Products, Inc. 2014 All rights reserved. Litho in U.S.A.

CRES COR reserves the right to change materials and

specications without notice.