Place cabinet near warm ovens. Do 1. NOT put in
drafty areas or near ventilating systems.
Plug power cord into proper wall outlet. 2.
Fill water pan (following steps a-c).3.
Use of treated or
CAUTION
operation and to maintain warranty.
soft water may be
required for proper
120202516.86015-20P
240192586015-15P
Rev. 20 (3/10)Page 1 of 4
HOW TO PROOF, continued:
Turn “RESERVOIR THERMOSTAT” to #9 and 5.
close the door.
NOTE: No. 9 setting will give you an approximately
90-95% humidity at 95°F (35°C). Experiment
with different settings to get the exact
temperature and humidity you need.
Thermometer shows the temperature inside the cabinet.
a. Lift off cover.
b. Fill with 3.5 qts. (3.3 liters) of water. Replace cover.
c. Adjust vents on cover to half open.
HOW TO PROOF:
Push switch to “HUMIDITY”. Yellow power light 1.
will come on.
Turn “RESERVOIR THERMOSTAT” to #10. Red 2.
heater light will come on.
Preheat cabinet for 30 minutes.3.
Put fresh or 4. fully thawed dough into cabinet.
NOTE: The cabinet temperature will drop temperature
inside cabinet if cold dough is added.
Do NOT put frozen dough into cabinet
PARTS IDENTIFICATION
1. Water Pan (Reservoir)6. Switch: ON/OFF
2. Reservoir Heater & Probe
3. Water Pan Cover8. Air Thermostat
4. Reservoir Thermostat9. Air Probe
5. Y ellow POWER light; Red
HEATER light for Reservoir
Models: 120-PH and 121-PH Series Proof/Hot Cabinets
NOTE: Check water level in water pan if you are
proofi ng longer than 90 minutes. Fill with
clean, hot water.
DRY PROOFING:
Turn air thermostat to #3 for 100°F (38°C) or higher.
HOW TO HEAT CABINET:
Push switch to “AIR”. The 1. Red indicator will light.
Turn “AIR THERMOSTAT” to temperature 2.
needed.
NOTE: No. 8 is approx. 175°F (79°C).
No. 6 is approx. 145°F (63°C).
No. 4 is approx. 115°F (46°C).
Proper food holding temperature is
140°F (60°C) or higher.
Preheat cabinet for 30 minutes.3.
Put food into cabinet.4.
FOR HUMIDITY:
Add water to water pan1.
Push switch to “HUMIDITY” for a few minutes.2.
TO TURN UNIT OFF: Push switch OFF.
5925 Heisley Road • Mentor, OH 44060-1833
MAINTENANCE
HOT UNIT REMOVAL INSTRUCTIONS:
Unplug power cord from wall outlet.1.
Remove two (2) screws from back of cabinet, one 2.
(1) above the receptacle and one (1) higher up,
holding the top of the tunnel.
Slide the entire unit out front of the cabinet, tilting 3.
it to clear the tie rod.
BEFORE cleaning
WARNING
the cabinet:
Allow cabinet to cool.1.
Remove Hot unit from cabinet.2.
Do NOT use abrasives or harsh 3.
chemicals.
Cleaning hints:
Wipe up spills as soon as possible.1.
Clean cabinet regularly to avoid heavy dirt build-up.2.
Make a test spot with cleaner.3.
Follow manufacturer’s directions on cleaner.4.
Do not mix cleaners.5.
Avoid drips and splashes.6.
HOW TO CLEAN THE UNIT:
SoilCleanerMethod
DOOR
(Laminated Vinyl)
CABINET
(Aluminum)
Inside
and
Outside
DIRTMild *detergent and water.
GREASE and OILWeak, alcohol-type cleaner.
DIRTMild *detergent and hot
FINGERPRINTS,
GREASE and OIL
WATER SPOTSMild abrasive cleaner1. Apply with damp cloth.
*Mild detergents include soaps and non-abrasive cleaners.