3. Instructions for use
1. Clip the output cord onto the massage pads.
2. Plug the output cord into the output jack of the controller.
3. Use a damp towel to wipe the skin where you put the pads, so as
to remove any body oil, cosmetic or dirt (Should the pads be soiled,
both their adhesivenessand the use time will be reduced).
4. Peel off the protective film on the pads.
Warning: Do not put two pads together in the process of using, to
avoid short cut.
5. Apply the pads to the areas of the body you want to massage. The
unit cannot operate unless both pads are applied.
Warning: Do not move pads or touch them with hands in the process
of using, it may cause strong stimulation.
6. Press button, the screen starts to display. The small flashing
hands on the LCD screen will automatically points at mode 1. The
“T” will automatically choose the state of 20minutes.
7. Touch mode area to select different modes (24 modes).
Mode 1 contains tapping, scrapping, body building, knocking
waveforms;
Mode 2 contains acupuncture, foot therapy, trigger point Lomi lomi
waveforms;
Mode 3 contains strike,reflexology,Tha chi,nuge massage waveforms;
Mode 4 contains kneading,butterfly,shiatsu-deep streching waveforms;
Mode 5 contains cupping, sports, Swedish thai waveforms;
Mode 6 contains rubbing, assorted,stepping,auto waveforms Please
increase the intensity when change to new mode because it will
return to be lowest automatically.
8. Press “+” button or click“+” on the screen to strengthen the
output power. Press “—” button or click“-” on the screen to reduce
the output power. One press to increase or reduce one grade, totally
20 grades. The chosen power output depends on the feeling comfort.
At the precondition of acceptance, the power should be chosen as
high as possible for the best effect.
9. Click timer figure to adjust time. The auto time set is 20 minutes.
One click to increase 10 minutes. The instrument sets time to auto
turn-off, and it should be restarted if treatment is needed to be
continued.
Note: The standard time is 20 minutes (time on the screen can be
adjusted). The devicecan be used 1 or 2 times (the maximum use
time) for the same area per day. There may be some people who feel
fatigue, in this case, lower the speed and strength, shorten the time
(for example stop the machine when the time shows 5 minutes), and
limit the use time to once a day.
10. Press bottom button to lock the LCD screen.When there is a key
showed on the top of the screen, it will be no uses no matter where
you touch on the screen, but the intensity level can be adjusted by
pressing side button. Press bottom button to unlock.
11. If you need to turn off the device during massaging, long press
“OFF” button.
12. Take off the physiotherapy film, cover the protectionfilm, and put
away the massager.
Note:
1.Never connect this product with common headphone.
2. Do not touch USB port in the process of using. The USB port is
only for charging- do not connect to any other device.
3. The charger supplied by the manufacturer must be in compliance
with IEC/EN 60601-1, the use of unauthorized charger can degrade
minimum safety.
4. Maintenance and Storage
1. Unplug the output cord from the output jack of the controller after
using.
2. Cover both pads with the protective film before storage.
3. Never fold the massage pads.
4. To keep the controller clean, use a soft and dry cloth for dust or a
soft damp cloth for any dirt and smudges. Do not use any cleaning
solutions to clean the controller and its pads.
5. Never apply the pads on any surface other than your skin. If the
pads become soiled or dirty, the adhesive power may decrease. In
this case, moisten the surface of the pads with water and wipe away
the dirty portion. This will allow a temporary restoration of the
adhesive power. However, too much water will result in loss of the
adhesive power.
6. Do not use or store the devices where there are magnetic fields or