Crelando 48420 User Manual

Page 1
EN
IE
Instructions for Use
No. 48420 Tjanting Set
Intended use
The electric Tjanting tool is solely intended for private non-commercial use in dry interior areas. It is a tool for individual creating batik patterns on fabric (like cotton, linen, half-linen, etc.) by means of liquid wax. Any other use is not permitted and can lead to injuries. In these cases the manufacturer carries no liability. The electric Tjanting tool is used to apply wax easily on fabric you want to design. After the wax has cooled down, put the fabric into the batik color (not included, observe the in­structions of the manufacturer of the batik color). Areas waxed on the fabric will remain uncolored. Wax batik is a fabric dyeing process where areas which are not to be dyed are covered with liquid wax.
Safety instructions
• CAUTION! When not in use, this device must be placed on the security stand (pos. VI).
• When the device is placed on the stand, the surface underneath must
be rm, not ammable and horizontal.
• This appliance can be used by children from 8 years on as well as by persons with restricted physical, sensory or intellectual abilities or lacking experience and knowledge if they are supervised or if they re­ceived instructions on how to use the appliance and they understand
the consequential hazards. Children are not allowed to play with the
appliance. Cleaning and maintenance must not be carried out by chil­dren without supervision.
• In order to avoid hazards, if the mains connection of this appliance is
damaged, it must be replaced by the manufacturer or his customer
service or a similarly qualied person.
• A re can break out if the appliance is not handled carefully.
• Ensure that the connecting cable does not come into contact with
heat, oil or sharp edges. Damaged connecting cables can cause res,
short-circuits and electric shocks.
• Before use, remove combustible objects, liquids and gases from the working area of the appliance. Keep your working area clean in order to prevent accidents.
• Before use, check that the wax pot is correctly attached to the appli­ance. The hot wax pot and its holder must not be brought into contact with skin, hair, etc. Risk of burns!
• After use, place the device on the stand and allow it to cool down be­fore packing it away.
• As long as it is in use, do not leave the appliance unsupervised.
• When the appliance is not in use, store it in a safe place protected from dust and moisture.
• Check the appliance for damage. Do not use if damaged!
• During use, ensure adequate ventilation. Ensure that no poisonous gases or vapours can be inhaled. Wear protective clothing.
• For longer work interruptions, disconnect the appliance from the volt­age source.
• Observe national and international safety, health and work protection regulations.
Scope of delivery
1 Tjanting tool 1 wax pot 1 safety stand 1 package wax (approx. 25 g) 1 Operating Instructions
Please check the goods for completeness.
Explanation of the pictures
j Tjanting tool k wax pot l wax m safety stand
Explanation of the symbols
Do not touch the tip of the tool (wax pot) during operation! The tip
is very hot! The same applies for the metallic tool holder as well as the upper part of the stand. Risk of burns!
Do not emerge the appliance into water and do not expose it to
moisture. Risk of electric shock!
Preparation
Please take your time and read the operating instructions carefully be­fore putting the appliance into operation and keep the operating instruc­tions for future reference.
It is not allowed to change settings or make modications from those set
by the manufacturer. It could be dangerous to change the structure of the device on your own authority, to remove parts or to use parts which are not approved by the manufacturer. (If you change the structure of the device on your own authority you risk e.g. an electric shock, a short circuit and burns.)
3452_cfhl_fly_GB_cs6.indd 1 14.08.14 08:42
The temperature of the wax pot as well as the liquid wax is very
high during operation! Risk of burns!
Put away the Tjanting tool correctly on the stand, if is on and not in
use (pos. VI).
Important information before start up
• Read the security instructions before putting the device into operation!
• Ensure that the working area is clean, even and dry.
• Before commencing, unpack the Tjanting Set completely and check the contents.
• The Tjanting tool and the wax pot are not pre-assembled for the initial start-up. The wax pot must be screwed on the device (see pos. I and II). To do so, you need a crosshead screwdriver (not included). In Tja­nting devices which are operated electrically, the wax is melted directly in the wax pot and kept liquid at constant temperature. This ensures constant and steady work.
• When processing multilayer fabrics (working with wax e.g. on the front side of a T-shirt) we recommend putting a protection ply (e.g. baking parchment) under the working area. This protection ply prevents un­intentional penetrating of the liquid wax on fabric areas which are not intended for dyeing.
Page 2
• Furthermore you can protect the working area e.g. with a foil (the fabric can stick together when applying wax) or you can stretch the fabric onto a frame before you start working.
• The textiles to be worked on must be clean and residue-free. Particular care must be paid to new textiles, which must be pre-washed to remo­ve possible residues.
• For this wax batik method, textiles made of cotton, linen and half-linen are perfectly suitable. We recommend cotton for the rst attempts sin­ce the melted wax penetrates optimally into the fabric.
• Liquid wax stiffens fast. For this reason we recommend melting only the amount of wax which is needed. Unexperienced users should therefore put just a very small amount of wax into the wax pot at the beginning.
• Work without interruptions. The applied wax cools down fast and har­dens.
• Before you start with the work, try out the device by applying the wax on a test fabric.
Start-up
• Fasten the wax pot to the device (see pos. I and II). Never screw the wax pot by force!
• Put the safety stand on an even, clean and dry working area (see pos. VI).
• Put the Tjanting tool on the safety stand (see pos. VI).
• Fill the wax pot (see pos. IV) with wax pellets (ll approx. ½ of the pot
with wax pellets).
• Make sure that the Tjanting device is placed securely on the stand (see pos. VI) and plug the jack of the device into the socket (see pos. III).
• Preheat the device for approx. 6 minutes (the heating time is depen-
dent on the ll-up quantity in the wax pot) until the optimal operating
temperature is reached.
• The optimal operating temperature is reached after the wax pellets have completely melted in the wax pot.
• The melted wax is applied (see pos. V) on the fabric by means of a small spout.
• You achieve ideal results when applying the liquid wax, if you only touch the fabric lightly with the top of the spout. Do not use any pressu­re. Putting pressure can lead to damages to the fabric and the spout.
• If the wax application is completed and the wax has hardened, the fabric can be dyed.
• Before coloring, always follow the instructions of the manufacturer of the batik color. You can obtain batik color and batik wax in DIY shops.
Only clean the surface of the tool tip with a dry cloth or a cleaning eece (e.g. CFH No. 52349) when it has cooled down. A cleaning eece is
available in many building stores and can be obtained there.
Warranty
The warranty for this device is 2 years from the date of purchase. The warranty starts with the date of purchase. Please keep the original receipt in a safe place. This document is required as a proof of purcha­se. If any material or manufacturing defects occur within 2 years from the date of purchase of this product, the product will be either repaired or replaced free of charge for you - at our discretion. This guarantee presumes that you submit the defective device and the proof of purcha­se (receipt) together with a short description of the defect and when the defect occurred within 2 years. In case that the defect is covered by our warranty, you will receive either the repaired product or a new one. In case of a warranty claim, please contact us by E-Mail under info@ cfh-gmbh.de. We will contact you immediately.
Disposal
The crossed through dustbin on this product indicates that at the end of its service life the appliance has to be disposed of separately and not together with household waste. Please bring the Tjanting tool to the established municipal collecting points in your local community. For disposal information and location of the nearest recycling park plea-
se contact e.g. Ofce for Municipal Sanitation or see Yellow Pages.
Technical Data
Power requirement: 230 V ~ 50 Hz
Output: 15 W Max. working temperature: approx. 155 °C (empty wax pot) approx. 175 °C (full wax pot with mel­ ted wax)
Subject to technical and optical changes.
Shut-down
• Put the Tjanting tool on its safety stand as shown in pos. VI (through
improper handling possible risk of burns and re!)
• The wax pot must be put onto the provided safety stand with high at­tention so that it stays in position.
• Now disconnect the device from the electrical outlet (unplug it).
• Let the Tjanting tool cool down completely.
• The remaining liquid wax can be kept in the wax pot. When the de­vice has cooled down completely, the wax hardens and can be melted again at a re-startup without any problems.
• If the appliance has not cooled down completely, do not leave it unat­tended.
• Depending on the ll-up quantity in the wax pot, the cooling-down time
can last up to 20 minutes.
• The environmental temperature has also inuence on the cooling
down time.
• When the completely cooled down device is not in use, store it in a safe place, protected from dust and moisture.
Tip
• The wax can be removed from the dyed and dry fabric by boiling, iro­ning with blotting paper or by dry cleaning. Follow instructions of the dye manufacturer.
• Should the spout be blocked, please proceed as follows: Unscrew the wax pot of the Tjanting device and put the wax pot into boiling water for a few minutes. Attention! At this process the wax pot must always be disconnected from the Tjanting device.
Service Address & Manufacturer:
Cleaning and maintenance
Only clean the Tjanting tool with a dry cloth when it has cooled down.
3452_cfhl_fly_GB_cs6.indd 2 14.08.14 08:42
Stand: VO-07/2014
Loading...