Creek Company ODC SPORT XL Assembly Instructions Manual

TTMM

ODC SPORT XL

TTMM

OUTDOOR DISCOVERY CRAFT

ASSEMBLY INSTRUCTIONS

THIS BOX CONTAINS:

STEEL FRAME

(1) Left Frame Member

(1) Right Frame Member

(1) Seat Support Frame Member with Padded Bottom

(1) Seat Back Frame

(1) Padded Seat Back

(2) Foot Bars

(1) Rear Frame Member

(1) Mesh Cargo Deck

(1) Stripping Apron

(12) Short Snap Pins

Each Pontoon consists of 840 Denier Nylon Cover with integral Side Storage Pockets,

Straps and Cam-lock Buckles to secure the Frame, and Main Bladder

with Valve Insert and Valve Plate all preassembled.

(2) Long Snap Pins

OARS & OARLOCKS

(1) Pair 6-foot 2 piece Oars

(1) Pair Clamp-on Oarlocks

PONTOONS

(1) Left Pontoon

(1) Right Pontoon

PUMP

Complete with a set of Adaptors

PATCH KIT

WARRANTY CARD

TTMM

ODC SPORT XL

OOUUTTDDOOOORR DDIISSCCOOVVEERRYY CCRRAAFFTT

ASSEMBLY INSTRUCTIONS

I. ASSEMBLE FRAME

NOTE: Your Frame Assembles using (2) Long Snap Pins and (12) Short Pins. Please follow instructions accordingly.

1. Assemble Cargo Deck by sliding Mesh Cargo Deck over Frame Member (see figure 1) and secure using attached

Hook and Loop andLadder Lock / Strap fasteners.

2. Assemble Padded Seat Back (see figure 1a) by sliding Padded Seat Back over the Frame Member.

3. Assemble Seat Support Frame Member to Left and Right Frame Members using (4) of the Short Snap Pins

(see figures 1 and 2.)

4. Assemble Cargo Deck to Left and Right Frame Members using (2) Short Snap Pins (see figures 1 and 2).

5. Assemble Foot Bars to Left and Right Frame Members using (2) Short Snap Pins (see figures 1 and 2).

6. Assemble Padded Seat Bottom to Seat Support Frame Member (see figure 1a and 2) using (4) Short Snap Pins.

7. Hold the Padded Seat Back vertically and attach to Padded Seat Bottom using (2) Long Snap Pins (see figures 1a

and 2). After assembly, Seat Back can pivot forward to fold seat down and pivot back to stop in a sitting position.

TTMM

II. PONTOON INFLATION

NOTE: Use the large cone Adaptor provided with your Pump. See figure 3b for a detail of the Valve Assembly. Before
inflation, be sure to fully seat each Valve Assembly into the Pontoon, screwing tightly by hand. When fully seating
Valve Assembly, be sure that the Valve Plate is in place around Valve Assembly and not restricting the Valve
Assembly from a full seal. After inflating, be sure to fully seat the top cap on to each Valve Assembly, screwing
tightly by hand. Both are required for an airtight seal.

1.

Inflate each Pontoon. The Valve is located inside the Storage Pocket of each Pontoon.(see figure 3).
Inflate until firm (do not over inflate).

2. Again, be sure top Valve Cap and Valve Assembly are fully seated.

PONTOON DEFLATION: Unscrew entire Valve Assembly from Pontoon.

III. ATTACH PONTOONS TO FRAME

NOTE: Always inflate the Pontoons first, before attaching to Frame.

1. Position inflated Pontoons under the Left and Right Frame Members with ODC Sport XL logos oriented to the

outside.The Frame Members fit around the Storage Pockets.

2. Attach Pontoons to Frame as illustrated in figures 3 and 3a. NOTE: Be sure the Straps are pulled tight through the
Cam-lock Buckles. Frame should be positioned forward or aft on the Pontoons to achieve center of gravity for an even
ride when fully loaded on the water.

IV. OAR & OARLOCK ASSEMBLY

1. Loosen the wingnut on the Oarlock and slide the Oarlock onto the handle end of the Oar Shaft.

2. Attach blade end of Oar Handle to end of Oar.

3. Place Oarlock Shafts into Frame.

4. With the Oarlocks installed on the Frame, the oars should be equally adjusted left and right allowing at least two

thumbs’ distance between the Oars, to avoid pinching your thumbs when rowing. With the blades perpendicular to
the water, tighten the wingnuts.

V. ATTACH STRIPPING APRON TO FRAME

1. Snap front two Straps around the Frame underneath the Oarlocks, and snap the back two Straps to the Seat Back Frame.

just below the Padded Back and just above the Seat Bottom Frame.