Page 1
You must read these instructions prior to using the
appliance and retain them for future reference.
Condensing
Tumble Dryer
Instruction Book
Page 2
Getting to know your Dryer 3
Important Safety Points 4
Installation of your Dryer 5
Caring for your Wash 6
Sorting your laundry 7
Items requiring special attention 8
How to operate your Dryer 9
Electrical Requirements 13
Caring for your Dryer 14
Something Wrong? Inside Back Cover
Service – Creda Tumble Dryers Back Cover
Contents
2
This appliance conforms to the following EEC Directives:
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
EEC Standards
Retention of this Instruction Book
This Instruction Book should be kept at hand, as it contains important details on the safe
and correct use of the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind,
make sure this Book is also provided so the new owner can become familiar with the
appliance and safety aspects.
Page 3
3
CONTROL PANEL
PUSH HERE TO
OPEN DOOR
AIR INTAKE GRILLE
PLINTH
(NOT ON ALL MODELS)
Features - Getting to Know Your Dryer
WATER CONTAINER
FLUFF
FILTER
SERIAL/MODEL No. (RECORD DETAILS ON SERVICE PAGE AT REAR.)
CONDENSER
REVERSIBLE
DOOR CATCH
Using your Dryer is easy. Nevertheless, for your own safety and to achieve the best
results, it is important to read through this handbook before using the appliance. Your
Condenser Dryer requires specific attention, more so than a vented dryer to maintain
optimum performance.
DOOR CATCH
Page 4
Note: This Dryer is only suitable for Domestic use.
Never allow children to play with
the Dryer.
Never switch the machine off
leaving a hot load in the drum.
Never tumble dry without the
filter, condenser and water
container in position.
Never exceed maximum
recommended load capacity.
Never place dripping wet
items in the drum.
Never allow lint to collect around
the Dryer.
Never use liquid conditioner in the
Dryer.
Do not dry articles that have not been
washed, rinsed and spun.
Never attempt to stand on top of your
Dryer.
Never dry fabrics that have been
chemically cleaned or have become
contaminated with solvents.
Never obstruct or drape anything over
the dryer which may block the rear
vents.
Always switch off at the Wall,
remove plug and close the
Door when not in use.
Always comply with the
specified electrical
requirements.
Ensure that your Dryer is
installed correctly and has
adequate ventilation.
Ensure air intake grille is
never obstructed or blocked.
Always finish every programme with
the cool cycle.
Always clean the filter of fluff after use.
Always empty Water Container after
every programme.
Always buy genuine Manufacturer’s
Spares and accessories.
Important Safety Points
Never ...
Always ...
4
✘ ✘
✘
✘
✘
✘
✘
✘
✘
✘
✘
✔ ✔
✔
✔
✔
✔
✔
✔
Page 5
5
Installation of your Dryer
There is no internal packing to be removed before use, but make
sure the drum is empty. Wipe the inside of the Drum before use to
remove any transit dust. Your Dryer does not blow moist air into
the room, avoiding the requirement of a vent hose.
Position the Dryer where air can freely circulate around it, a 15mm
gap each side is recommended.
The door of your Dryer is reversible and can easily be changed
before installation. Exchange diagonally the hinge brackets for
blanking plugs. Exchange door latch and catch with their
opposing blanking plates. See diagram above.
Support the weight of the door when removing hinges.
Dryers can be to permanently stack on top of Washing machines,
saving valuable floor space. The Dryer should not be
located next to a hob, cooker, heater or high level grill, as heat
from these appliances could cause damage. When ordering you
must state the product numbers of the Washing machine and
Tumble Dryer (Tel. No. 0541 530 530).
Note: Separate mains plugs and sockets must be used for each
appliance. Do not use 2-way adaptors or extension leads.
As the dryer is heavy assistance should be obtained when
stacking the dryer.
HINGE
HINGE
DOOR
LATCH
DOOR
CATCH
Location
Door Reversal
Instructions
Stacking Your
Appliance
Page 6
The following wash-care labels should be observed.
The majority of fabrics today can be dried in a Dryer. There are however certain fabric
finishes which need to be dried away from direct heat.
Item can be used in Dryer.
Do not use in Dryer.
Dry at high heat setting.
Dry on low heat setting.
Caring for your Wash
Items not suitable for your Dryer ...
Fabric Conditioner
For really fresh and soft fabrics, we recommend you use a liquid fabric conditioner in the final
rinse of your wash. This helps to eliminate the build up of static.
6
Items containing Rubber or Plastic
film, e.g. pillows, cushions, PVC
rainwear.
Inflammable articles or items
containing inflammable
substances, e.g. towels
contaminated with hair lacquer.
Fibreglass, e.g. some types of
curtains.
Items which have been dry cleaned.
Woollen articles.
Large bulky items, e.g. pillows,
continental quilts, sleeping bags,
double blankets and large bedspreads.
Page 7
The same care should be taken for Drying fabrics as when
Washing, e.g. split fabric groups, close all zips and hooks, belts
and strings should be tied in loose bow.
It is important to extract as much water as possible from each item
before drying. This reduces the drying time, energy consumption
and the running cost.
Cotton fabrics max. 6 Kg (13.2 lb)
Synthetics, eg Polyester, polycotton max. 3 Kg (6.6 lb)
Acrylics max. 2 Kg (4.4 lb)
Note: Man-made fibres require more space to dry without creasing.
If cotton/terry towelling items are grouped with synthetic fabrics
they could remain damp at the end of the drying cycle. If this
occurs, simply replace cottons for a short period of drying to
finish off.
The table below shows the approximate weight of everyday items.
Sorting your laundry
7
Maximum Dry
Load Size
Typical Load
Clothing articles
Household items
Blouse Cotton
Other
150g
100g
5oz
4oz
Dress Cotton
Other
Cotton
Other
500g
350g
1 lb 2oz
12oz
Jeans 700g 1 lb 6oz
10 Nappies 1000g 2 lb 3oz
T-shirt
(Note: 1 Kg = 1000g)
150g 5oz
Shirt 300g
200g
10.5oz
7oz
Duvet cover
(Double)
Cotton
Other
1500g
1000g
3 lb 5oz
2 lb 4oz
Tablecloth Large
Small
Double
Single
700g
250g
1 lb 6oz
9oz
Tea Towel 100g 4oz
Bath Towel 700g 1 lb 8oz
Sheets 500g
350g
1 lb 2oz
12oz
Hand Towel 350g 12oz
Note: When drying
sheets, part way
through the cycle,
remove and open them
out to ensure full and
even drying.
To continue the
programme press the
start button.
Page 8
Items requiring special attention
8
Drying requirements of blankets and bedspreads vary according to size,
weight and fabric.
If you have difficulty getting them into the Dryer, the machine will have
difficulty drying them properly as they expand when drying and prevent
air flow through the Dryer. This can cause the appliance to overheat.
Blankets (e.g. Acrilan, Courtelle, Dralon and Orlon) must never be over
dried. Such acrylic fabrics should be dried with care on low heat.
Always refer to manufacturers drying instructions.
Always dry starched articles separately from your normal garments.
Ensure as much of the solution is removed from the garments as possible
before placing in the Dryer.
Use a slightly heavier starch solution than you would when drying items
on the washing line.
If garments are over dried the starch will powder, leaving the fabric
limp.
Blankets and
Bedspreads
Permanently
pleated or creased
garments
Starched articles
Page 9
How to operate your Dryer
9
1. Ensure hands are dry. Plug the appliance in. Switch on at the
wall socket.
2. Open the Door by pressing the Front panel as shown.
3. Place the selected fabrics into the Dryer. Ensure the fabrics
are pushed towards the back of the Drum and away from the
Door seal.
4. Always check the following:
5. Close the Door.
6. Select the required heat setting.
Press switch in at Top
Low Heat Acrylics and Synthetics
Press switch in at Bottom
High Heat Cottons
PUSH HERE &
RELEASE TO
OPEN DOOR
FLUFF FILTER
is clean and in place
WATER CONTAINER
is empty and in place
CONDENSER
is in place
Press here for Low
Press here for High
Page 10
The timer control gives you the choice of either Eco/
Economy or timed drying.
To select the Eco/Economy programme turn the
timer control clockwise to the E position. The
ecosense/economy light will switch on. When the
load is dry this programme automatically advances
into the cool cycle, at which point the ecosense/
economy light will switch off.
Select the required Drying time by rotating the Timer
control clockwise (up to 120 minutes) just past the
required time, then anti-clockwise to the desired time.
Refer to the Drying guide.
10
TIMER
CONTROL
How to operate your Dryer
The Timer control can be set manually to any time (up to 100 minutes). This is particularly
useful for damp dry results.
The Eco/Economy option optimises the energy efficiency, saving time and money for the
user.
7. Rotate the Timer control to select the appropriate required drying
time. All of our Dryers have an energy saving feature which
reduces the heat input when the temperature in the drum reaches
a predetermined level.
Timed Dryers:
Automatic Eco/Economy
Dryer:
NOTE: Never force the Timer control beyond the
stop positions.
NOTE: Only turn the Timer control clockwise.
START
BUTTON
FILTER CARE
(NOT ALL
MODELS)
EMPTY WATER
LIGHT
HEAT
SWITCH
CONTROL
PANEL
START
BUTTON
ECOSENSE/
ECONOMY
LIGHT
EMPTY WATER
LIGHT
HEAT
SWITCH
CONTROL
PANEL
TIMER
CONTROL
ECO/
ECONOMY
PROGRAMME
0
10
20
30
40
50
60
70
80
90
100
110
120
cool
0
E
0
80
cool
100
90
70
50
40
30
60
20
10
cool
a
u
t
o
m
a
t
i
c
t
i
m
e
d
d
r
y
i
n
g
Page 11
8. Press and release the START switch to commence the Drying
programme.
9. The Heating programme can be terminated at any time by
turning the Timer control to the Cool cycle position.
10. Allow the Cool cycle to finish then remove the laundry from the
appliance. This reduces creasing of fabrics.
11. Ensuring hands are dry, switch off the Appliance and
remove and plug from the wall socket.
12. Always remove and clean the Filter after EVERY programme.
A light will come on when you open the door to remind you to
clean the fluff filter on some models.
11
How To Operate Your Dryer
NOTE: If the Door is opened during a programme, the Dryer
will automatically stop. To continue the programme, upon
closing the Door, the START switch must be re-pressed.
NOTE: Always complete a programme with the Cool cycle.
Never switch the Dryer off, leaving a hot load in the Drum.
NOTE: Wash or vacuum clean the filter occasionally.
The drying time will depend on the size of the load, the type of
fabric and the wetness of the load. It is therefore not possible to
give exact drying times but experience will quickly enable you to
set the appropriate time for fully drying or damp drying to your
requirements. As an approximate guide, the following table may
assist you. The times shown include the cool tumble period, in
minutes.
The Kg weights specified are fabric dry weights.
Drying Times
& Heat Settings
ACRYLICS
COTTONS
High heat
1 Kg 2 Kg 1 Kg 2 Kg
40-50 50-70
3 Kg
70-90 40-60 55-75
1 Kg
30-40
2 Kg
40-55
Half
Load
3 Kg
55-70
4 Kg
70-80 80-90
5 Kg
95-120
Full
Load
6 Kg
Half
Load
Full
Load
Half
Load
Full
Load
Low heat Low heat
Drying times when spun at 800-1100rpm in
washing machine
Drying times – reduced
spin in washing machine
Drying times –
reduced spin in
washing machine
SYNTHETICS
Page 12
14. EVERY month, remove and clean the Condenser unit by pouring cold
water through all the tubes. This prevents the air passage ways from
being blocked by fluff.
13. Remove plinth moulding (where fitted) by
slightly lifting and sliding to the left. Remove the
water container and empty after EVERY
programme. Failure to do this will result in the
water container becoming full and the load will
not dry.
12
How To Operate Your Dryer
NOTE: The light on the control panel only comes on when the
water container is full. When the light is on you should stop
the dryer and empty the water container. This should be
avoided by emptying the container between cycles. If the
light comes on during a cycle (Eco machines) the timer will
automatically advance to ‘cool run’.
SINK
WATER
CONTAINER
WATER
CONTAINER
FLUFF
FILTER
REAR
FRONT
TAP
CONDENSER
EMPTY WATER
CONTAINER
LIGHT
PLINTH MOULDING
WHEN FITTED
Page 13
Supply
Changing the
Plug
This appliance should be connected to the mains supply via a
suitable switched socket, which is in a position accessible after
installation. Refer to rating plate for the supply voltage.
Warning: This appliance must be earthed.
The flexible mains lead is supplied connected to a BS1363 fused
plug with a 13 amp capacity.
Rewirable Plug
Moulded Plug
The wires in the mains lead are in accordance with the following:
GREEN/YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
If the plug is changed, the coloured wires in the mains lead may
not correspond with the colours of the markings identifying the
terminals in the plug. Therefore wire is as shown above. Should the
mains lead ever require replacement, this operation must be
carried out by a competent person. Only use specially prepared 3
core 1.50mm
2
recommended spares cable.
The correct replacement of the fuse is identified by the colour
coding in the base of the plug or the colour that is embossed in
words in the base of the fuse recess, or elsewhere on the plug.
Only 13 amp replacement fuses which are ASTA approved to
BS1362 should be fitted. After replacement of a fuse in the plug, the
fuse cover must be refitted. Fuse covers may be obtained from
your local Regional Electricity Company.
Electrical Requirements
13
If this plug is removed or cut off, it should be properly disposed
of and not left where children might find it and plug into a
supply socket – with the obvious consequent danger of
electrocution.
WARNING: The plug must not be used without a fuse cover.
NOTE: Replacement mains cables must only be obtained from our recommended
Spares stockist.
NOTE: IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN.
13
AMP
FUSE
BROWN
TO
LIVE
CORD
CLAMP
BLUE
TO
NEUTRAL
GREEN & YELLOW
TO EARTH
Page 14
To maintain the performance of the Dryer, follow the simple steps
below:
Switch off the electricity and remove the plug, ensuring hands are
dry.
Turn the Drum by hand to ensure all items have been removed.
Clean the Filter by rinsing under the tap or using a vacuum
cleaner.
Empty the Water Container.
Wipe the drum, the front of the condenser and the door seal with a
damp cloth.
Remove Condenser unit and clean any build up of fluff or lint from
between the plates by rinsing it under the tap with cold water.
This should be done from the rear of the Condenser unit.
Clean exterior metal and plastic surfaces with a damp cloth or
silicon polish only.
Every 6 months vacuum the Air intake grille and Vents at the rear
of the appliance, to remove any build up of fluff or lint.
Do not use abrasive cleaners, scouring agents, acids, chlorine
bleach or metal polish to clean any part of the appliance as they
may cause damage.
Occasionally clean the surface of the sensor inside the drum with
vinegar to remove water contaminants. Apply carefully with a
cloth. This will maintain the drying performance of the machine.
To minimise the risk of injury to children please dispose of your
product carefully and safely. Remove all doors and lids (where
fitted). Remove the mains cable (where fitted) by cutting off flush
with the appliance and always ensure that no plug is left in a
condition where it could be connected to the electricity supply.
To help the environment, Local Authority instructions should be
followed for the disposal of your product.
Caring for your Dryer
Disposal of the appliance
14
When not in use:
After each load:
Every week:
Every month:
Cleaning:
Automatic/
Economy Models
Page 15
Before calling a Service Engineer, please check through the following list.
THERE MAY BE NOTHING WRONG
Something Wrong?
DRYER WILL NOT START
Has the fuse blown in the plug or the
main fuse box?
(Try plugging in another appliance to
check)
CHECK THE POWER SUPPLY
LOAD IS NOT DRY OR TAKES
LONGER THAN NORMAL TO DRY
If the fuse has blown in the plug
top, refer to Electrical Requirements.
Are you using an extension lead?
(Many extension leads are not
suitable. Try plugging the Dryer
directly into a socket to check.)
Does the fluff filter need cleaning?
(It should be cleaned after every load)
Does the water container need
emptying?
(It should be emptied after every load)
Does the Condenser unit need
cleaning?
(It should be cleaned every month)
Have the Air intake grille or rear
Vents of the Dryer been obstructed?
Has the Empty water light come on?
(Empty the Water bottle after every load)
Is the Door fully closed?
(Try opening and closing the door again)
Have you selected the correct heat
setting? (Refer to Drying Guide and
check the heat setting switch)
Have you mixed cottons with
synthetics? (See page 7)
Has the Timer control been set?
(Try resetting the timer and pressing the
start button again)
Have you selected the correct time
for the load? (Refer to Drying Guide –
this can vary according to Washing
machine spin speeds, load size and
fabrics being dried).
Has the Start button been pressed
hard enough? (Try pressing Start again)
IMPORTANT NOTICE: The Start
button must be pressed every time the
door is opened to re-start the
programme.
If you have been through the above and there is still a problem, you should identify your
Service Agent using the list on the next page and contact your Local Service Office.
CHECK THE FOLLOWING
CHECK THE SETTINGS CHECK THE SETTINGS
Page 16
Your In-Guarantee Service Telephone Number
If you have any other queries regarding Service or Parts, our Parts and Service division will be
pleased to help. You should write to :
Creda Service, Customer Service Department, Blythe Bridge, Stoke-On-Trent. ST11 9LN.
For Parts and Accessories, please telephone our Parts Order Hotline on
0541 530 530 (UK) or 01 842 6836 (Republic of Ireland).
UK 0541 500 500
Republic of Ireland 1850 302 200
Note 1 : If under guarantee, our Engineers will need to see a copy of your purchase
receipt when they call.
Note 2 : Our Engineers will use every effort to avoid damage to floor coverings and
adjacent units when carrying out repair/service work, but in locations where
the Engineer advises you that it will be impossible to move the appliance
without risk of damage, he will only proceed with your approval that no
liability will be accepted.
Service
Please carry out the checks detailed on the Something Wrong page. If there is a
problem with your appliance then contact your Service Centre by using the table below to
identify the appropriate phone number.
Please have the following information available when you call :
1. (a) Your name.
(b) Your address and postcode.
(c) Your telephone number.
2. The date and the name of the shop/retailer where the appliance was purchased.
3. The Model number and Serial number of your appliance (See Features page for
Rating plate location).
4. Clear and concise details of the fault.
5. Details of any Extended Warranty or Service Insurance Schemes.
Model Number : Serial Number :
Shop / Retailer : Date :
PRINTED BY SIMLEX .FOUR ASHES, WOLVERHAMPTON. August 1998 Part No. 377400003-02
Loading...