Creda ARE150, ARE200, ARE075, ARE100, ARE050 User Manual
OPERATING
INSTRUCTIONS MANUAL
Arezzo Electric Radiator
Models: ARE050 / ARE075 / ARE100 / ARE150 / ARE200
These instructions should be read carefully and
retained for future use. Note also the information
presented on the appliance.
INCEUKE3RG ISSUE 0
IMPORTANT
These instructions should be read carefully and retained for future use.
Note also the information presented on the appliance.
IMPORTANT SAFETY ADVICE
When using electrical appliances, basic precautions should always be followed
to reduce the risk of re, electrical shock, and injury to persons, including the
following:
IMPORTANT – The wall bracket supplied with the appliance must be used.
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF
A BATH, A SHOWER OR A SWIMMING POOL.
IMPORTANT – If the heater is installed in a room containing a bath or shower, it must
be so installed that switches and other controls cannot be touched by a person using
a bath or shower.
Do not use outdoors.
Do not locate the heater immediately below a xed socket outlet or connection box.
WARNING: In order to avoid overheating, do not cover the heater. Do not place material
or garments on the heater, or obstruct the air circulation around the heater, for instance
by curtains or furniture, as this could cause overheating and a re risk.
NEVER cover or obstruct in any way the heat outlet slots at the top of the heater or the
air inlet slots in the base of the heater.
The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of re that
exists if the heater is accidentally covered.
CAUTION - Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
This appliance can be used by children aged from 8 years and above and by persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/o the appliance
provided that it has been placed or installed in its intended normal operating position
and they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and clean the appliance or perform user
maintenance.
Note that due care and consideration must be taken when using this heater in series
with a thermal control, a program controller, a timer or any other device that switches
on the heat automatically, since a re risk exists when the heater is accidentally covered
or displaced.
If the supply cord is damaged it must be replaced by the manufacturer or service agent
or a similarly qualied person in order to avoid a hazard.
WARNING: Servicing and product repairs should only be undertaken by the
manufacturers approved service agent or a similarly qualied person, using only exact
manufacturer approved spare parts.
2
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent electrician, and be in strict
accordance with the current I.E.E. Regulations for Electrical Equipment in Buildings. The
wires in this mains lead are coloured in accordance with the following code:
GREEN AND YELLOW: EARTH
BLUE:
BROWN
BLACK
NEUTRAL
: LIVE
PILOT WIRE
- see also ‘Pilot Wire Connection’.
2
The heater is tted with a length of exible cable type H05VV-F size 4 x 1.0mm
for
connection to the xed wiring of the premises through a suitable connection box
positioned adjacent to the heater.
A means for disconnection must be incorporated in the xed wiring of the premises in
accordance with the wiring rules. The supply circuit to the heater must incorporate a
double pole isolating switch having a contact separation of at least 3mm.
Pilot Wire Connection
The BLACK control wire is designed to carry a signal from a wall mounted Creda
programmer. If a programmer is not being used, the pilot wire should be isolated in
accordance with the current IEE Wiring Regulations.
IMPORTANT - DO NOT connect the BLACK pilot wire to earth. Care should be taken
with the installation of the pilot wire(s) as when switching to background (setback) they
become energised at 240V although only at a current of less than 100mA. In every case
a suitable means of isolation must be provided for the pilot wire and marked to indicate
that two sources of supply may be present at the heater. Where pilot wires are installed
separately from the heater nal sub-circuit they should be protected, double insulated
and carry their own integral earth continuity conductor.
Supplementary Earth Bonding
Should Equipotential Earth Bonding be required the earthing conductor in the supply
cord is deemed to provide the supplementary bonding connection (see Regulation
544.2.5, 17th Edition I.E.E. Wiring Regulations).
Please note that lit cigarettes, candles and oil burners, combined with the
convection effect of electric heaters can cause soot deposits to build up on the
surface directly above and to the sides of the heater. This is not a fault of the
heater. Extensive burning of candles or smoking in the operating environment of
this product can produce heavy discolouration within a few months of use.
3
General
The heater is designed for wall mounting using the wall bracket supplied. It should
only be operated when in the upright position as shown - see Fig. 1 and Fig. 2. All
models are splash proof to IP24 standard and may be used in bathrooms, however
not in the immediate vicinity of baths, showers, water connections, wash basins or
swimming pools. Before connecting the heater check that the supply voltage is the
same as that stated on the heater.
Wall Mounting
IMPORTANT – The wall bracket supplied with the appliance
must be used. The heater should be positioned observing the
minimum clearances stated around the heater - see Fig. 1 and
Fig. 2.
DO NOT locate the heater immediately below a xed socket
outlet or connection box.
1. Remove wall mounting bracket from the back of the heater
by depressing the spring latch at the top of each bracket see Fig. 3.
2. Fix the wall bracket securely to the wall through the four
screw holes provided.
3. Present the heater to the wall bracket, and engage lower
slots in the back with bracket.
4. Raise the heater to upright position and push the heater
onto bracket to engage top latches.
Dimensions
Model(s) Watt (kW) A (mm)
ARE050 0.50 kW 513
ARE075 0.75 kW 513
ARE100 1.0 kW 675
ARE150 1.5 kW 756
ARE200 2.0 kW 918
4
Fig. 1
Fig. 2
150 mm
(Min)
150 mm (Min)
A
546 mm
Shelf
300 mm
105 mm
Fig. 3
275 mm
294 mm
(Min)
Model (s) A (mm)
ARE050 225
ARE075 225
ARE100 387
ARE150 468
ARE200 630
A
260 mm (Min)
5
Notes to the Installer
Test Mode
When the heater is connected via a pilot wire system, the test mode allows the
installer to conrm that the heater is responding correctly to the incoming pilot
wire signal.
Pilot wire mode must be enabled in the heater’s settings in order for the appliance
to be controlled by a Creda controller with pilot wire connection.
Press Menu, Back and Enter for ten seconds to enter the service menu, select
Pilot Wire and press Enter. Select Enable.
The desired comfort temperature should be selected
using
and . Press Enter to conrm.
Note: The comfort
temperature can be
changed later if required.
The heater will now enter a test state for four minutes.
During this test state the display screen will indicate
the pilot wire status. Each pilot wire mode should be
veried to ensure correct operation.
Note: Some features are
not available while pilot
wire mode is enabled.
Comms
Standalone
Pilot Wire
RF Module
Select
Comfort SP
21 °C
Test Mode
Pilot Wire
Status
Comfort
Time
remaining
4:00
Safety - Overheat protection
For your safety this appliance is tted
with a thermal cut-out. In the event
that the product overheats for some
reason, the cut-out prevents excessive
temperatures on the product by cutting
the power to the heater. Once the
heater has cooled down, it will reset
6
automatically, it will continue to cycle on
and o automatically until the reason for
overheating is removed.
The display screen will ash red to
indicate the product has overheated. To
reset the display, remove the obstruction
and hold Enter for 10 seconds.
Loading...