Creative Play JC102 Installation Instructions Manual
REF: JC102 - JUNGLE CLIMBER midi
pg 1 of 46
JUNGLE CLIMBER
Installation Instructions
Parts Required
Tools Required
Foundation Details
Surfacing Details
Step by step Instructions
Additional Drawings
Notes
pages 2 - 25 EXTERNAL FABRICATION
(pg. 2 - 6)
(pg. 10)
(pg. 11 - 43)
(pg. 44 - 45)
(pg. 46)
(pg. 8 - 9)
(pg. 7)
CONTENTS
REF: JC102 - JUNGLE CLIMBER midi
pg 2 of 46
PARTS required
VT1 VT2 VT3
VT6 VT7 VT8 VT10VT9
VT3 VT4 VT5
Vertical Timbers
VT1 - QTY - 1 125mm dia @ 2215mm (6 x holes & chamfer 1 end)
VT2 - QTY - 1 125mm dia @ 2215mm (2 x holes & chamfer 1 end)
VT3 - QTY - 2 150mm dia @ 2331.5mm (1 x holes, 4 x ‘CUT-OUTS’ & chamfer 1 end)
VT4 - QTY - 1 125mm dia @ 2215mm (1 x holes & chamfer 1 end)
VT5 - QTY - 1 125mm dia @ 1700mm (1 x holes & chamfer 1 end)
VT6 - QTY - 1 125mm dia @ 1750mm (2 x holes & chamfer 1 end)
VT7 - QTY - 1 125mm dia @ 2215mm (2 x holes & chamfer 1 end)
VT8 - QTY - 1 125mm dia @ 2215mm (1 x holes & chamfer 1 end)
VT9 - QTY - 1 125mm dia @ 2215mm (2 x holes & chamfer 1 end)
VT10 - QTY - 1 125mm dia @ 1700mm (2 x holes & chamfer 1 end)
(ALL POST WILL BE LABELLED)
REF: JC102 - JUNGLE CLIMBER midi
pg 3 of 46
PARTS required continued...
MT1 - QTY - 1 125mm dia @ 3650mm (6 x holes & chamfer BOTH ENDS)
MT2 - QTY - 1 125mm dia @ 2711.5mm (3 x holes & chamfer BOTH ENDS)
MT3 - QTY - 1 125mm dia @ 3000mm (7 x holes & chamfer BOTH ENDS)
MT4 - QTY - 1 125mm dia @ 3650mm (14 x holes & chamfer BOTH ENDS)
MT5 - QTY - 1 125mm dia @ 3000mm (7 x holes & chamfer BOTH ENDS)
MT6 - QTY - 1 125mm dia @ 3000mm (2 x holes & chamfer BOTH ENDS)
MT7 - QTY - 1 125mm dia @ 3000mm (7 x holes & chamfer BOTH ENDS)
(ALL POST WILL BE LABELLED)
Main Horizontal Timbers
MT1 MT2
MT3
MT4 MT5
MT7
MT6
REF: JC102 - JUNGLE CLIMBER midi
pg 4 of 46
PARTS required continued...
Additional Timbers
AT1 - QTY - 3 150mm dia @ 230mm (2 x holes)
AT2 - QTY - 1 125mm dia @ 1742mm (5 x holes & chamfer BOTH ENDS)
AT3 - QTY - 1 125mm dia @ 1450mm (1 x holes & chamfer BOTH ENDS)
AT4 - QTY - 1 125mm dia @ 1625mm (1 x holes & chamfer BOTH ENDS)
AT5 - QTY - 1 125mm dia @ 1013.5mm (2 x holes & chamfer BOTH ENDS)
AT6 - QTY - 1 125mm dia @ 2037mm (1 x holes & chamfer BOTH ENDS)
AT7 - QTY - 1 125mm dia @ 3100mm (4 x holes & chamfer BOTH ENDS)
AT8 - QTY - 1 125mm dia @ 2271mm (1 x holes & chamfer BOTH ENDS)
AT9 - QTY - 1 125mm dia @ 2129mm (1 x holes & chamfer BOTH ENDS)
(ALL POST WILL BE LABELLED)
AT1 x 3 AT2 AT9AT8
AT4 AT6 AT7AT5AT3
REF: JC102 - JUNGLE CLIMBER midi
pg 5 of 46
PARTS required continued...
CARGO NET
QTY - 1 ASSEMBLY
QTY - 1 ASSEMBLY
SUPPLIED LOOSE
Consists of...
T1 / T2 / T3 / T4 timbers
R1 / R2 / R3 / R4 Ropes
NET CLIMBER
R1
T1
T2
T3
T4
R2
R3
R4
NET + BLOCKS
REF: JC102 - JUNGLE CLIMBER midi
pg 6 of 46
PARTS required continued...
x10 (FM80 ‘Brass screws’)
To be used for HEX BOARD steps
x8 (M12 x 320* CUP SQUARE BOLTS)
*or closest size available NOT SMALLER
x39 (‘NYLOCS’ M12 - Nylon locking nuts)
x42 (‘NYLOCS’ M10 - Nylon locking nuts)
To be used for M10 EYEBOLTS on net assemblies
x31 (M12 x 290* CUP SQUARE BOLTS)
*or closest size available NOT SMALLER
x16 (Polyfix halves)
To be used for NET+BLOCKS
x70 (120 Distance piece)
120 label is shown on the inside
x8 (140 Distance piece)
140 label is shown on the inside
x73 (Covered end cap R60)
NOT STANDARD END CAP - has a
radius cut into it
x2 (HEX BOARD ‘STEP’ with cut out) x1 (HEX BOARD ‘STEP’)
x1 rope @ 2542mm
IR1
x1 rope @ 3426mm
IR2
x1 rope @ 2556mm
IR3
x1 rope @ 2099mm
IR4
IR1
IR2
IR3
IR4
INDIVIDUAL ROPES
REF: JC102 - JUNGLE CLIMBER midi
pg 7 of 46
TOOLS required
x1 (14mm - Long combination auger bit - 400mm)
To be used for DRILLING THROUGH 2 x 125mm dia timbers
x2 (HEX BOARD ‘TIMBER MARKER GUIDE’)
To be used for MARKING the 125mm dia timbers
x2 (QUICK RELEASE CLAMPS)
SPECIFIC JUNGLE CLIMBER TOOLS
REF: JC102 - JUNGLE CLIMBER midi
pg 8 of 46
Foundation Details
FOUNDATIONS 400mm x 400mm x 750
RED FOUNDATIONS 400mm x 600mm x 750
*REMEMBER - 750mm below FINISHED GROUND LEVEL - if WETPOUR / MULCH / PLAYSAFE is to be laid amend as required
VT1
VT6
VT7
VT9
VT8
VT10
VT3
VT3
VT4
VT5
VT2
REF: JC102 - JUNGLE CLIMBER midi
pg 9 of 46
Foundation Details
VT3 TIMBERS ARE SET AT A 45 degree ANGLE - the ‘edge’ of the 600mm measurement is where the post meets the ground level
ALL OTHER VT TIMBERS ARE POSITIONED UPRIGHT
SOIL
FINISHED GROUND LEVEL
TIMBER SUPPORT POST
CONCRETE
REF: JC102 - JUNGLE CLIMBER midi
pg 10 of 46
Surfacing Details
RED DIMENSIONS CENTRE OF VERTICAL TIMBERS TO SURFACING
REF: JC102 - JUNGLE CLIMBER midi
pg 11 of 46
Installation + Assembly Instructions
Construct the main assembly BEFORE laying concrete
foundations STEPS to
NOTES:
- All timbers bolted together MUST include 2 x DISTANCE
PIECES
TIMBERS DO NOT BOLT DIRECTLY TO EACH OTHER
- Install STEP by STEP
TO ENSURE THE CORRECT HOLES ARE USED AT EACH STAGE
- TAKE EXTRA CARE WHEN DRILLING
TAKE EXTRA PRECATION WHEN DRILLING THE TIMBERS - ONCE POSITIONED REMEMBER TO ALLOW FOR THE DISTANCE PIECES AND MARK
ACCORDINGLY (distance between timbers 27mm)
- DRILLING THROUGH THE CENTRE
ALTHOUGH SOME HOLES ARE DRILLED AT AN ANGLE - THE HOLE IS DRILLED THROUGH THE CENTRE OF THE TIMBER (LEAVING 62.5mm
either side)
1
1 19
REF: JC102 - JUNGLE CLIMBER midi
pg 12 of 46
Installation + Assembly Instructions
Position the VT4 / VT5 / VT9 / VT10 timbers
VERTICAL TIMBERS (VT) are CHAMFERED at one end only - ENSURE THIS END IS NOT IN THE GROUND
Attach MT7 to VT5 / VT10 timbers
Using M12 x 290* CUP SQUARE BOLTS / ‘NYLOCS’ M12 / Covered end cap R60 / 120 Distance pieces
2 x 120 distance pieces
Covered end R60
M12 NYLOC
M12x290 BOLT
2
3
VT9
VT10
VT10
VT4
VT5
VT5
MT7
REF: JC102 - JUNGLE CLIMBER midi
pg 13 of 46
Installation + Assembly Instructions
ENSURE the positioning of the MT7 is correct
The 4 remaining holes in the MT7 are positioned closer to the VT10 timber
Attach MT6 to VT9 / VT10 timbers
Using M12 x 290* CUP SQUARE BOLTS / ‘NYLOCS’ M12 / Covered end cap R60 / 120 Distance pieces
4
5
VT10
MT7
VT9
VT10
MT6
REF: JC102 - JUNGLE CLIMBER midi
pg 14 of 46
Installation + Assembly Instructions
ENSURE the positioning of the MT6 is correct
There is a remaining HIGHER hole in the VT9 (in the opposite direction) - CIRCLED RED BELOW
Attach MT5 to VT4 / VT9 timbers
Using M12 x 290* CUP SQUARE BOLTS / ‘NYLOCS’ M12 / Covered end cap R60 / 120 Distance pieces
6
7
VT9
VT9
VT10
VT4
VT4
VT5
MT6
MT5
MT7
(4 x HORIZONTAL holes
for NET ASSEMBLY)
The VERTICAL hole is
positioned CLOSER to the
VT4 timber
Loading...