Creative Labs EF0810 Users Manual

SXFI AIR

Super X-Fi Bluetooth® Headphones

使用产品前请阅读使用说明

Model No. / 型號 / 型号: EF0810

PN: 03EF081000000 REV A

Overview

4

5

6

7

8

10

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C Port

10. 3.5mm Analog Jack

3

2

1

9

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

The Bluetooth

use of such marks by Creative Technology Ltd. and its afliates is under license.

®

word mark and logo are owned by the Bluetooth® SIG, Inc. and any

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH
(4.81Wh)

Enhance Your Audio

Unleash the performance of Super X-Fi with the
SXFI App and SXFI Control App

Charging

Built-in Battery

Charging SXFI Air when it is switched off

• Built-in LED will blink in Green every 2 secs

• Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink

twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Other Information

Supplementary documentation for this product includes a detailed user guide, DoC
and safety and regulatory information. These documents can be downloaded from
the creative.com/support/SXFI Air site.
Compliance markings can be seen on the surface upon removal of ear cup cushion
which can be removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to

switch on

• Press and hold for 2 secs

again to switch off

• Press and hold shortly to

indicate battery level. RGB
Lighting will blink twice in
Red in off mode if battery
level is low

RGB Lighting:

Blue OR User’s Color

Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs

to initiate Bluetooth pairing

• Press and hold for 2 secs

again to cancel

Voice Prompt:
Now In Pairing Mode

S

E

O

U

C

R

Note:
Bluetooth will cancel
discovery mode if no device
is paired within 30 secs.
Bluetooth can only be
paired in standalone state

Note:

Mobile app is required to

establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note:
Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Blue­tooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

Connecting/Disconnecting
Bluetooth:

• Bluetooth will auto connect

to last paired device when
switched on

Bluetooth Reset:

• Press and hold for 8 secs till

the RGB Lighting blink twice
in Red

• RGB Lighting will revert to

default color once Bluetooth
Reset is complete

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth

Pairing for 2 secs

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-FI Button

Touch Pad

• Increase Volume:

Headphones will play a tone

at Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function

by swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter Mass Storage mode

• Tap and hold for 4 secs again to exit Mass Storage mode

Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play
when switching on/off.

Shufe Mode:

• Tap once to shufe

Note:
Only applicable to Micro SD card playback

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to

deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi

button before powering up
the headphones

Voice Prompt:

• Shufe On

• Shufe Off

RGB Lighting:
Blink once in Green
when activated
Blink once again
in Orange when
deactivated

RGB Lighting:
Solid Green

FR

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C Port

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Other information

Les documents supplémentaires concernant ce produit incluent un guide de l’utilisateur détaillé, la
DoC, ainsi que des informations réglementaires et liées à la sécurité. Ils peuvent être téléchargés
sur le site creative.com/support/SXFI Air. Conservez ce document pour pouvoir vous y référer

ultérieurement.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

© 2018 Creative Labs Pte. Ltd. All rights reserved. Creative, the Creative logo, X-FI,
SXFI and the Super X-Fi logo are trademarks or registered trademarks of Creative
Technology Ltd in the United States and/or other countries. All other trademarks

are the property of their respective owners and are hereby recognized as such. All
specications are subject to change without notice. Use of this product is subject to

a limited hardware warranty. Actual contents may differ slightly from those pictured.

© 2018 Creative Labs Pte. Ltd. Tous droits réservés. Creative, le logo Creative, X-FI,

SXFI et le logo Super X-Fi sont des marques ou des marques déposées de Creative
Technology Ltd. aux États-Unis et/ou dans les autres pays. Toutes les autres marques
appartiennent à leurs propriétaires respectifs. Toutes les spécications peuvent faire
l’objet de modications sans préavis. L’utilisation de ce produit est soumise à une

garantie limitée sur le matériel. Le contenu réel peut légèrement différer de celui
présenté.

DE ES IT RU

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C-Anschluss

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Weitere Informationen

Die Zusatzinformationen zu diesem Produkt bestehen aus einem detaillierten Benutzerhandbuch,
DoC sowie Sicherheits- und Bestimmungsangaben. Diese Dokumente sind auf der Website creative.
com/support/SXFI Air als Download verfügbar. Bewahren Sie dieses Dokument zur späteren
Referenz auf.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. Puerto USB-C

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Otra información

La documentación complementaria para este producto incluye una guía del usuario detallada, así

como una “declaración de conformidad” (DoC) e información sobre normativa y seguridad. Estos

documentos se pueden descargar en el sitio creative.com/support/SXFI Air. Guarde este documento
para futuras consultas.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. Porta USB-C

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Altre informazioni

La documentazione aggiuntiva per questo prodotto include una dettagliata guida utente, DoC e
informazioni e normative sulla sicurezza. I documenti possono essere scaricati dal sito creative.com/

support/SXFI Air.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. Порт USB-C

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Дополнительная информация

Дополнительная документация для данного устройства включает в себя подробное
руководство пользователя, декларацию соответствия (DoC), а также сведения о
безопасности и стандартах. Эти документы можно загрузить с веб-узла creative.com/support/
SXFI Air site. Сохраните данный документ для использования его в будущем.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

CZ PL SK JP

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C Port

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Další informace

Dodatečná dokumentace k tomuto výrobku zahrnuje podrobnou uživatelskou příručku, dokumenty
(DoC) a informace o bezpečnosti a souladu s předpisy. Tyto dokumenty lze stáhnout na adrese
creative.com/support/SXFI Air. Tento dokument si ponechejte pro pozdější použití.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C Port

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Inne informacje

Dokumentacja uzupełniająca dla tego produktu zawiera szczegółową instrukcję dla użytkownika,
certykat zgodności (DoC) oraz informacje na temat bezpieczeństwa i przepisów prawnych. Doku­mentację można pobrać z witryny pod adresem creative.com/support/SXFI Air. Niniejszy dokument
należy zachować na przyszłość.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C Port

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

Ďalšie informácie

Ďalšia dokumentácia pre tento výrobok obsahuje podrobný návod na obsluhu, DOC a informácie
o bezpečnosti a právnyc¬h predpisov. Tieto dokumenty si môžete prevziať z lokality creative.com/
support/SXFI Air. Tento dokument uschovajte na budúce použitie.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-Cポート

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

その他の情報

本製品のユーザーガイドや安全についての補足文書についてはjp.creative.com/support からダウン
ロードできますのでお読みください。 今後参照する時のために、このクイックスタートガイドは大切に保管
しておいてください。

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

KO CS

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C 포트

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

기타 정보

이 제품에 대한 추가 설명서에는 자세한 사용 설명서, 문서 및 안전, 그리고 규제 관련 정보가
포함되어 있습니다.

이 설명서는 creative.com/support/SXFI Air 사이트에서 다운로드할 수 있습니다. 나중에 참조할 수
있도록 이 문서를 보관해 두십시오.

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

Overview

1. RGB Lighting

2. High Density Memory Foam

3. Durable Hybrid Headband

4. Super X-FI Button

5. SD Card Slot

Specication

Headphones

• Driver: 50mm Neodymium magnet

• Frequency response: 20 Hz ~ 20 kHz

• Impedance: 32 Ω

• Sensitivity: 105 dB/mW @ 1 kHz

• USB input: 5 V

Microphone

• Type: Unidirectional noise-reduction

• Frequency response: 50 Hz ~ 15 kHz

• Impedance: <2.2 kΩ

• Sensitivity: -42 dB @ 1 kHz

Enhance your audio

Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App

6. Bluetooth / Source Button

7. Power Button

8. NanoBoom Mic

9. USB-C端口

10. 3.5mm Analog Jack

Wireless Type: Bluetooth 4.2
Bluetooth Proles:

• A2DP (Wireless stereo Bluetooth)

• AVRCP (Bluetooth remote control)

• HFP (Hands-free prole)
Input: 5V 1A
RF Output Power: < 4dBm

Operating temperature: 0°C to 45°C

Wireless Range: Up to 10m

Charging Time: 2.5hr
Play Time: Up to 8hr playback time
Audio Codec: SBC

Lithium Ion Battery: 3.7V 1300mAH (4.81Wh)

Charging

Charging SXFI Air when it is switched off

- Built-in LED will blink in Green every 2 secs

- Built-in LED will turn off when fully charged

Voice Prompt:

- Battery Level Low

- Battery Level Medium

- Battery Level High

Note:

• RGB Lighting will light up and indicate Battery Level when switched on

• When battery is low, headphones will prompt “Battery Level Low” every 10 minutes

• Headphones will not switch on when battery is too low

• Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /

SD Card. Headphones will start charging when connected via USB to a power source except in
the following modes: USB Mode / Mass Storage Mode

• Battery Level is also indicated in app for user’s reference

Factory Reset

1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red

2. RGB Lighting will revert to default color once Factory Reset is complete

Voice Prompt: Reset to Factory Default

Note: Factory Reset can also be triggered via Windows app

其他信息

此产品的补充文档包括详细的用户手册、DoC 和安全说明以及规章信息。 这些文档可以从 creative.
com/support/SXFI Air 网站下载。 请保留此文件，以备今后参考。

Compliance markings can be seen on the surface upon removal of ear cup cushion which can be
removed by hand.

Keep this document for future reference.

Power Button

Power Button:

• Press and hold for 2 secs to switch on

• Press and hold for 2 secs again to switch off

• Press and hold shortly to indicate battery level. RGB Lighting

will blink twice in Red in off mode if battery level is low

RGB Lighting:

Blue OR User’s

Color Setting

Bluetooth / Source Button

Bluetooth Pairing:

• Press and hold for 2 secs to initiate Bluetooth pairing

• Press and hold for 2 secs again to cancel

S

E

O

U

C

R

Voice Prompt:
Now In Pairing Mode

Connecting/Disconnecting Bluetooth

• Bluetooth will auto connect to last paired device when

switched on

Bluetooth Reset:

• Press and hold for 8 secs till the RGB Lighting blink

twice in Red

• RGB Lighting will revert to default color once

Bluetooth Reset is complete

Note: Bluetooth will cancel discovery mode if no device is paired
within 30 secs. Bluetooth can only be paired in standalone state

Voice Prompt:
Bluetooth Reset

BLE Pairing:

• Trigger pairing on mobile app

• Press and hold Bluetooth Pairing for 2 secs

Note:

Mobile app is required to establish BLE connection

Change Sources:

Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio)

Voice Prompt:

- Bluetooth

- SD Card

- USB

Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode,

Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources

RGB Lighting:
Blinks in Blue when in
Pairing Mode

Super X-Fi Button

Enabling Super X-FI:

• Press once to activate SXFI

• Press once again to deactivate SXFI

Recovery Mode:

• Press and hold Super X-Fi button before powering

up the headphones

Touch Pad

• Increase Volume:

Headphones will play a tone at

Maximum Volume

• Decrease Volume

• Previous Track

• Next Track

• Call Panning:

Activate Call Panning function by

swiping Left/Right.

Default Call Direction: Center

Cycle Sequence (Left Swipe):

Right > Center > Left

Cycle Sequence (Right Swipe):

Left > Center > Right

Note:
Switching on/off Mass Storage mode takes 15
secs. 2 short beeps will play when switching
on/off.

Shufe Mode: Tap once to shufe

RGB Lighting:
Blink once in Green when
activated Blink once
again in Orange when
deactivated

RGB Lighting:
Solid Green

Initiate Voice Assistant:

• Tap and hold for 2 secs to initiate

voice assistant

Incoming Call:

• Tap twice to answer incoming call

• Tap twice again to end call

Initiate Playback:

• Tap twice to initiate playback

• Tap twice again to pause playback

Mass Storage Mode:

• Tap and hold for 4 secs to enter

Mass Storage mode

• Tap and hold for 4 secs again to exit

Mass Storage mode

Voice Prompt:

• Shufe On • Shufe Off

Note: Only applicable to Micro SD
card playback

EN

FR

DE

ES

IT

PL

NL

PT

SV

The use of the WEEE Symbol indicates that this product may not be treated

as household waste. By ensuring this product is disposed of correctly,
you will help protect the environment. For more detailed information
about the recycling of this product, please contact your local authority,
your household waste disposal service provider or the shop where you
purchase the product.

L’utilisation du symbole DEEE indique que ce produit ne peut être traîté

comme déchet ménager. En garantissant la mise au rebut appropriée

de ce produit, vous contribuez à préserver l’environnement. Pour plus
d’informations sur le recyclage de ce produit, contactez les autorités
locales, le fournisseur de service d’élimination des déchets ménagers ou
le magasin où vous avez acheté le produit.

Die Verwendung des WEEE-Symbols gibt an, dass dieses Produkt nicht

als Haushaltsmüll betrachtet werden kann. Durch die korrekte Entsorgung

dieses Produktes tragen Sie zum Schutz der Umwelt bei. Ausführliche
Informationen zum Recycling des Produkts erhalten Sie über die örtlichen
Behörden, die für Sie zuständige Müllabfuhr oder das Geschäft, in dem Sie

das Produkt erworben haben.

El uso del símbolo RAEE (WEEE) indica que el producto no se puede

tratar como un desecho doméstico. Si se deshace de este producto
debidamente, contribuirá a proteger el medioambiente. Si desea obtener

información detallada acerca del reciclaje de este producto, póngase en

contacto con las autoridades locales, el servicio de recogida de basura o

la tienda donde ha adquirido el producto.

L’uso del simbolo RAEE indica che questo prodotto non deve trattato
come un riuto domestico. Assicurandosi che questo prodotto sia smaltito
correttamente, si contribuisce a proteggere l’ambiente. Per informazioni
più dettagliate sul riciclaggio di questo prodotto, rivolgersi agli enti locali, al
fornitore del servizio di smaltimento dei riuti domestici o al negozio in cui
è stato acquistato il prodotto.

Symbol WEEE wskazuje, że ten produkt nie może być traktowany
jako odpad gospodarczy. Zapewniając prawidłową utylizację produktu
pomagasz w ochronie środowiska. Aby uzyskać szczegółowe informacje
na temat utylizacji produktu, należy skontaktować się z lokalnymi
władzami, przedsiębiorstwem świadczącym usługi usuwania odpadów z
gospodarstwa domowego lub sklepem, w którym zakupiono produkt.

Gebruik van het WEEE-symbool betekent dat het product niet als normaal
huishoudelijk afval mag worden verwerkt. U helpt met de bescherming van
het milieu door dit product op correctly wijze te verwijderen. Voor meer

informatie over het recyclen van dit product, neemt u contact op met het
gemeentehuis, uw afvaldienstverlener of de winkel waar u het product hebt
gekocht.

O uso do símbolo REEE indica que este produto não pode ser tratado
como resíduo doméstico. Ao garantir que este produto é eliminado

correctamente, estará a proteger o ambiente. Para obter informações mais
detalhadas sobre a reciclagem deste produto, contacte as autoridades

locais, o fornecedor de serviços de eliminação de lixo doméstico ou a loja
onde adquiriu este produto.

Användningen av WEEE-symbolen anger att produkten inte får hanteras
som hushållsavfall. Genom att säkerställa att produkten hanteras på rätt sätt
bidrar du till att skydda miljön. Mer detaljerad information om återvinningen
av denna produkt får du hos den lokala återvinningsorganisationen,
bolaget som hanterar dina hushållssopor eller den återförsäljare där du
köpte produkten.

NO

DK

HU

EL

LT

SK

CZ

RU

Hereby, Creative Labs Pte. Ltd. declares the Bluetooth

Bruken av WEEE-symbolet indikerer at dette produktet ikke kan
behandles som husholdningsavfall. Du vil bidra til å beskytte miljøet
ved å sørge for at dette produket blir avhendet på en forsvarlig måte. Ta
kontakt med kommunale myndigheter, renovasjonsselskapet der du bor
eller forretningen hvor du kjøpte produktet for å få mer informasjon om

resirkulering av dette produktet.

Brugen af WEEE symbolet angiver, at dette produkt ikke må behandles
som husholdningsaffald. Ved at sikre at produktet bortskaffes korrekt, vil
du hjælpe med til at beskytte miljøet. For mere detaljerede oplysninger

om genbrug af dette produkt, bedes du kontakte din kommune, dit

renovationsselskabs tjenesteudbyder eller den butik, hvor du købte

produktet.

FI

WEEE-symbolin käyttö ilmaisee, että tätä tuotetta ei saa hävittää
kotitalousjätteen seassa. Huolehtimalla siitä, että tämä tuote hävitetään
asianmukaisesti, autat suojelemaan ympäristöä. Pyydä tarkempia
kierrätysohjeita paikallisilta viranomaisilta, jäteyhtiöltä tai liikkeestä, josta

ostit tuotteen.

A WEEE szimbólum azt jelzi, hogy a terméket nem szabad általános
háztartási hulladékként kezelni. A termék megfelelő ártalmatlanításával
hozzájárul a környezet védelméhez. A termék újrahasznosításával
kapcsolatos részletes tudnivalókért forduljon a megfelelő helyi hatósághoz,
hulladékgyűjtő vállalathoz vagy a terméket árusító üzlethez.

Η χρήση του συμβόλου WEEE δηλώνει ότι δεν μπορείτε να
αντιμετωπίζετε αυτό το προϊόν ως οικιακό απόβλητο. Βεβαιώνοντας
της κατάλληλη απόρριψη του προϊόντος αυτού, βοηθάτε στην
προστασία του περιβάλλοντος. Για περισσότερες πληροφορίες
σχετικά με την ανακύκλωση αυτού του προϊόντος, επικοινωνήστε με
τις τοπικές αρχές, την υπηρεσία απόθεσης οικιακών απορριμάτων ή
το κατάστημα από όπου αγοράσατε το προϊόν.

EEĮA simbolis rodo, kad produkto negalima išmesti kartu su buitinėmis
atliekomis. Tinkamai išmesdami šį produktą padėsite saugoti aplinką. Dėl
išsamesnės informacijos, kaip perdirbti šį produktą, kreipkitės į vietines
atsakingąsias institucijas, buitinių atliekų perdirbimo paslaugų teikėją arba
į parduotuvę, kurioje įsigijote šį produktą.

Použitie symbolu WEEE označuje, že tento výrobok sa nesmie likvidovať
s komunálnym odpadom. Ak výrobok správne zlikvidujete, prispejete
k ochrane životného prostredia. Podrobnejšie informácie o recyklácii
výrobku získate na miestnom zastupiteľstve, u poskytovateľov služieb
likvidácie domového odpadu alebo v predajni, v ktorej ste výrobok zakúpili.

Použití symbolu WEEE označuje, že tento výrobek nesmí být považován
za domovní odpad. Zajištěním správné likvidace tohoto výrobku pomáháte
chránit životní prostředí. Podrobnější informace o recyklaci tohoto výrobku
získáte od místních úřadů, od rmy, která u vás zajišťuje odvoz odpadků,
nebo v obchodě, kde jste výrobek zakoupili.

Использование символа WEEE означает, что данный продукт не
может рассматриваться в качестве бытовых отходов. Соблюдая
правильную утилизацию этого изделия, вы поможете защитить
окружающую среду. Для получения более подробной информации
о переработке изделия, пожалуйста, обратитесь в местные органы
власти, в службу сбора бытовых отходов или в магазин, где был
приобретен продукт.

EN

compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at http://www.creative.com/EUDoC
Please visit creative.com/support/SXFI Air for user guide, safety and regulatory
information and battery removal instruction, which is meant strictly for independently

qualied professional.

Par la présente, Creative Labs Pte. Ltd. déclare ce Casque micro Bluetooth® que le

FR

modèle n° EF0810 est conforme à la Directive 2014/53/EU. L’intégralité du texte de

la déclaration de conformité européenne est disponible sur http://www.creative.com/
EUDoC

Hiermit erklärt Creative Labs Pte. Ltd. dass Bluetooth

DE

Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist

unter http://www.creative.com/EUDoC verfügbar.

Por el presente, Creative Labs Pte. Ltd. declara que el Auriculares Bluetooth

ES

micrófono, modelo nº EF0810 cumple con lo establecido en la Directiva 2014/53/UE. El
texto completo de la declaración de conformidad de la UE está disponible en http://www.
creative.com/EUDoC

Creative Labs Pte. Ltd. dichiara che Cufe Bluetooth

IT

alla Direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è

disponibile su http://www.creative.com/EUDoC

Настоящим документом Creative Labs Pte. Ltd. заявляет, Беспроводная гарнитура

RU

модель № EF0810 полностью соответствует Директиве 2014/53/ЕС. Полный текст
Декларации о соответствии требованиям ЕС доступен на сайте http://www.creative.

com/EUDoC

Společnost Creative Labs Pte. Ltd. tímto prohlašuje, Náhlavní souprava Bluetooth

CZ

model č. EF0810 vyhovuje směrnici 2014/53/EU. Úplné znění EU prohlášení o shodě je
k dispozici na http://www.creative.com/EUDoC

Spółka Creative Labs Pte. Ltd. niniejszym oświadcza, że Zestaw słuchawkowy Blue-

PL

SK

JP

KO

CS

®

, model EF0810 jest zgodny z dyrektywą 2014/53/UE. Z pełnym tekstem deklaracji

tooth

zgodności UE można zapoznać się pod adresem http://www.creative.com/EUDoC

Hereby, Creative Labs Pte. Ltd. declares the Bluetooth
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at http://www.creative.com/EUDoC

Hereby, Creative Labs Pte. Ltd. declares the Bluetooth
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at http://www.creative.com/EUDoC

Hereby, Creative Labs Pte. Ltd. declares the Bluetooth
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at http://www.creative.com/EUDoC

Hereby, Creative Labs Pte. Ltd. declares the Bluetooth
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at http://www.creative.com/EUDoC

®

headset, model no. EF0810 is in

®

-Headset, Modellnr. EF0810 der

®

con

®

, modello n. EF0810 è conforme

®

headset, model no. EF0810 is in

®

headset, model no. EF0810 is in

®

headset, model no. EF0810 is in

®

headset, model no. EF0810 is in

Техника безопасности

Ознакомьтесь с информацией, содержащейся в данном разделе, чтобы
обеспечить условия безопасного использования изделия и снизить риск
поражения электрическим током, возникновения короткого замыкания,
нанесения травм, возгорания, ухудшения слуха и прочих опасностей.
Неправильная эксплуатация изделия может привести к аннулированию
гарантии. Дополнительную информацию см. в гарантийном документе,
входящем в комплект поставки.

• Не разбирайте и не пытайтесь самостоятельно ремонтировать изделие.
Все работы по техническому обслуживанию и ремонту должны проводить
квалифицированные специалисты.

• Запрещено эксплуатировать устройство при температурах ниже 0°C (32°F)
и выше 45°C (113°F).

• Запрещено пробивать или повреждать корпус устройства и бросать его в
огонь.

• Держите устройство вдали от источников мощных магнитных полей.

• Запрещено подвергать изделие сильным механическим воздействиям и
ударам.

• Запрещено подвергать изделие воздействию воды или влаги. Если продукт
устойчив к высокой влажности, не погружайте его в воду и не выносите
под дождь.

®

,

Тип оборудования: Беспроводная гарнитура
Модели, торговая марка: EF0810, Creative
Питание: 5V 1.0A
Производитель: Creative Labs Pte. Ltd.
Страна происхождения: китай

Название и адрес представителя в таможенном союзе:
ООО “Прокси”, 142281, Московская
область, город Протвино, Оболенское шоссе, д.2, к.216.,
Номер телефона : [phone]
[phone]
Электронный адрес : [e-mail]
Данная контактнаяинформация только для соответствующих органов
таможенного союза (Россия, Белоруссия и Казахстан) по вопросам
соответствия продукции Для информации о продукте илигарантии,
пожалуйста, посмотрите гарантийный талон из комплекта поставки ата
производства (месяц и год): Указана на упаковке.
Данное устройство отвечает требованиям Технического регламента
Таможенного союза ТР ТС 020/2011 “Электромагнитная совместимость
технических средств” утв. Решением КТС от 09.12.2011г. №879

Additional Safety and Regulatory information for

Creative SXFI AIR

Regulatory Information

The following sections contain notices for various countries:

CAUTION: This product is intended for use with FCC/CE certified computer equipment. Please check the
equipment operating/installation manual and/or with the equipment manufacturer to verify/confirm if your
equipment is suitable prior to the installation or use of the product.

Notice for the USA

Federal Communication Commission (FCC) Interference Statement

FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more
of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired
operation.

CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules,
this device must be installed with computer equipment certified to comply with Class B limits.

All cables used to connect to the computer and peripherals must be shielded and grounded. Operation with
non-certified computers or non-shielded cables may result in interference to radio or television reception.
may result in interference to radio or television reception.

MODIFICATION: Any changes or modification not expressly approved by the grantee of this device could void
the user’s authority to operate the device the user’s authority to operate the device.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Notice for Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of

the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.

Canada Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet équipement est conforme aux limites d’exposition aux radiations IC CNR-102 établies pour un
environnement non contrôlé. Cet émetteur ne doit pas être situé ou fonctionner conjointement avec une
autre antenne ou un autre émetteur.

MODIFICATION: Any changes or modification not expressly approved by the grantee of this device could void
the user’s authority to operate the device.

Toute modification non approuvée explicitement par le fournisseur de licence de l’appareil peut entraîner
l’annulation du droit de l’utilisateur à utiliser l’appareil.

Ukraine RoHS Statement

Обладнання відповідає вимогам Технічного регламенту щодо обмеження використання деяких
небезпечних речовин в електричному та електронному обладнанні, затвердженого постановою
Кабінету Міністрів України від 3 грудня 2008 № 1057

充電式電池リサイクルについてのご注意

クリエイティブの一部製品にはリチウムイオン充電池が使用されています。

Li - ion

リチウムイオン充電池はリサイクル可能な資源です。

• クリエイティブ製品に内蔵されている充電池をリサイクルするには、充電池の取り外しはお客様ご自身で
は行わないで下さい。リサイクルの方法などのお問い合わせは、クリエイティブメディア株式会社のカスタ
マーサービスセンター (http://jp.creative.com/support/contact/日本語のみ）にご相談下さい。

• 取り外しが可能なクリエイティブ製品の充電池をリサイクルするには –

!

注意事项

• 安全の為、電力を完全に使い切ってから充電池を取り外して下さい。

• 安全の為、充電池の金属端子部分にはセロハンテープなどの絶縁テープを貼って下さい。

• 安全策を講じた使用済み充電池は、充電式電池のリサイクル協力店へお持ち下さい。 充電式電池の回

収/リサイクルおよびリサイクル協力店については、中間責任法人JBRCのホームページ http://www.
jbrc.com/ を参照して下さい。

Vietnam RoHS Statement

This product is in compliance with Circular 30/2011/TTBCT of the Ministry of Trade of the Socialist Republic
of Vietnam (“Circular”), it does not contain the following substances in concentration greater than the
Maximum Limit value as specified in the Circular.

Substance Maximum Limit (ppm) 1, 2

* lead 1000

* mercury 1000

* cadmium 100

* hexavalent chromium 1000

* polybrominated biphenyls (PBB) 1000

* polybrominated diphenyl ethers (PBDE) 1000

1

Maximum Limit does not apply to applications exempted from the Circular.

2

Maximum Limit refers to concentration by weight in homogeneous materials.

SUPPLIER’S DECLARATION OF CONFORMITY

According to CFR Title 47 §2.1077

Importer’s Name:
Importer’s Address:

declares under its sole responsibility that the product

Trade Name:
Model Numbers:
Product Name:

has been tested according to the FCC / CISPR22 requirement for Class B devices
and found compliant with the following standards:

EMI/EMC: ANSI C63.4 & C63.10, FCC Part 15 Subpart B & C
Complies with Canadian ICES-003 Class B & RSS-247 standards

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including Interference that may cause undesirable operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.

Creative Labs, Inc.
1901 McCarthy Boulevard
Milpitas, CA. 95035
Tel: [phone]

Creative
EF0810
Creative SXFI AIR

Supplementary Information: Thinh Bui

Compliance Manager
Creative Labs, Inc.
14th Dec 2018

JP

安全に関する注記

内蔵 バッテリー

• 内蔵バッテリーを取り外さないでください。
本製品は、各地の環境規制に準じて処分する必要があります。バッテリーを交換する場合は、お住まいの地域

のサポート営業所に製品をお送りください。 製品サービス情報については、
www.creative.comをご 覧くださ い。

• 直射日光や火等の過度の熱にさらさないでください。
注意: バッテリーが不適切な種類と交換されると、爆発する危険があります。交換は種類が同じまたは

同等の電池のみを使用してください。

(Bluetoothデバイス用の追加ガイドライン)

• Bluetoothデバイスの短波無線周波数信号は、他の電子機器や医療機器の動作に悪影響を及ぼすことが
あります。

• 使用を禁止されている場所ではデバイスの電源をお切りください。医療施設、飛行機、燃料補給地点、自動ド
ア付近、自動火災報知機付近、その他の自動制御機器の近くでこのデバイスを使用しないでください。

• このデバイスはペースメーカーや他の医療機器から20cm以上離してください。電波により、ペースメーカー
やその他の医療機器の動作に悪影響を及ぼすことがあります。

KO

안전 지침

내장된 배터리

• 내장된 배터리를 제거하지 마십시오.

제품은 해당 지역 환경 법규에 따라 폐기해야 합니다. 배터리를 교체하려면 지역에 제품을 반환사무실을

지원합니다. 제품서비스 정보에 대해 알아보려면 www.creative.com을 방문하십시오.

• 이러한 햇빛 화재 나 좋아하는 같은 과도한 열에 노출시키지 마십시오.

주의: 배터리가 잘못으로 대체하는 경우 폭발의 위험유형입니다. 동일하거나 같은 형식의 배터리 만

교체.

Bluetooth

장치에 대한 추가 지침)

(

• Bluetooth 장치의 단파 무선 주파수 신호는 다른 전자 및 의료 장비의 작동에 영향을 미칠 수 있습니다.

• 사용이 금지된 곳에서는 장치를 끄십시오. 의료 기관, 항공기, 급유 지점, 자동문, 자동 화재 경보기 또는

기타 자동으로 제어되는 장치 근처에서는 사용하지 마십시오.

• 이 장치를 심장 박동 조절 장치 및 기타 의료 장비에서 최소 20cm 멀리 두십시오. 라디오파가 심장 박동

조절 장치 및 기타 의료 장비의 작동에 손상을 끼칠 수 있습니다.

BI

Instruksi Keselamatan

Baterai Tersemat

• Jangan coba-coba melepas baterai yang tersemat.

Produk ini harus dibuang sesuai dengan peraturan lingkungan setempat. Untuk mengganti baterai,

kembalikan produk Anda ke kantor dukungan di wilayah Anda. Untuk informasi layanan produk,
kunjungi www.creative.com.

• Jangan sampai produk terkena panas yang berlebih seperti sinar matahari atau sejenisnya.

PERHATIAN: Berisiko meledak jika baterai diganti dengan tipe yang salah. Gantikan hanya dengan

jenis yang sama atau yang setaraf.

(Panduan tambahan untuk perangkat Bluetooth)

• Sinyal frekuensi radio gelombang pendek dari perangkat Bluetooth dapat mengganggu fungsi
perangkat elektronik dan medis lain.

• Matikan perangkat jika dilarang menggunakannya. Jangan gunakan perangkat di fasilitas medis,
pesawat, pom bensin, dekat dengan pintu otomatis, alarm kebakaran otomatis, atau perangkat lainnya
yang dikendalikan secara otomatis.

• Jauhkan perangkat ini setidaknya 20 cm dari alat pacu jantung dan perangkat medis lain. Gelombang
radio dapat mengganggu fungsi alat pacu jantung dan perangkat medis lainnya.

AR