Creative Labs CB2455 User Manual

En_CB2455.book Page 1 Wednesday, June 8, 2005 9:32 AM

Creative Handsfree CB2455 with

Bluetooth Technology

Vo lu me Increase

Microphone

Power adapter jack

When your headset is not in use, clip the earpiece to your headset as shown below.

button

Volume Decrease button

Light Emitting Diode (LED)

Multi-function button

Earpiece

En_CB2455.book Page 2 Wednesday, June 8, 2005 9:32 AM

Getting Started

Charge your headset

Fully charge your headset before using it for the first time. This takes approximately five hours. To charge your headset’s battery, connect the power adapter to your headset. Consequently, charging your headset takes three hours.

Pair your headset and mobile phone

1. If your headset is turned on, turn it off by pressing and holding the Multi-function button until the LED turns red.

2. Place your headset within one meter of your mobile phone.

3. Press and hold the Multi-function button and one of the Volume buttons simultaneously, until the LED alternately blinks red and blue.

4. Turn on your mobile phone’s Bluetooth feature. For more information, see your mobile phone’s documentation.

5. Set your mobile phone to detect Bluetooth devices.

6. From the list that appears, select CB2455Creative.

7. When prompted for a passkey, enter 0000 to complete pairing.

• Some mobile phones require an additional connection step after pairing.

• If the pairing is not completed within two minutes, your headset turns itself off automatically.

• If your headset is successfully paired to your mobile phone, the LED blinks blue five times, and then once every five seconds.

En_CB2455.book Page 3 Wednesday, June 8, 2005 9:32 AM

Using Your Headset

Usage Action Turning on

headset Turning off

headset

Making a call

Answering a call

Ending a call

Using Voice Dial*

Using Last Number Redial*

Adjusting volume

Rejecting a call Press and hold the Multi-function button for three seconds. Putting a call on

hold Switching between

calls Muting or

unmuting the microphone

Clearing all headset pairings

*Some features are available only for certain mobile phones. Refer to your mobile phone’s documentation.

Press and hold the Multi-function button for three seconds. The LED turns blue.

Press and hold the Multi-function button until the LED turns red.

Make sure that your headset is turned on (it may be in standby mode when inactive), dial the number, and then proceed with your call.

If there is an incoming call, your earpiece and mobile phone rings, and your headset beeps. Press the Multi-function button.

Press the Multi-function button to end a call. You can also end a call using your mobile phone.

Press the Multi-function button and when you hear a beep, say the voice tag.

Press the Multi-function button twice within one second.

Press the Volume Increase or Volume Decrease button to gradually increase or decrease the volume.

Press and hold the Volume Increase and Volume Decrease buttons simultaneously, for one second.

Press the Volume Increase and Volume Decrease buttons simultaneously.

Press and hold one of the Vol u me buttons until the LED alternately blinks red and blue. To unmute the microphone, press one of the Vol um e buttons.

Make sure that your headset is turned off. Press and hold both Vo lu me buttons simultaneously for 20 seconds. The LED alternately blinks red and blue. Press and hold both Volume buttons for two seconds. You hear two beeps and your headset turns itself off automatically. Charge your headset for a few seconds to reset your headset. All current pairings are cleared.

En_CB2455.book Page 4 Wednesday, June 8, 2005 9:32 AM

Reading your headset’s LED

The table below shows you the various LED indications available.

LED Meaning

Red

Blue

Blue and red

On (when charging) Battery is charging. Blinks every five

seconds On (when charging) Fully charged. Blinks once every five

seconds Blinks once every 15

seconds

Blinks alternately

Battery low.

Headset is paired to your mobile phone and is in standby mode.

Call in progress.

Headset is in pairing mode and is ready for pairing. OR Headset is paired, connected and the microphone is muted.

General Specifications

Bluetooth operation: • Bluetooth version 1.2 compliance

• Bluetooth 2.4 GHz Class 2 radio, up to a radius of 10 meters (32.8 feet) (varies depending on environment)

Supported Bluetooth profile: Headset and Handsfree profiles

Frequency range: 2.4000 - 2.4835 GHz

Battery type: Built-in Lithium-ion battery (rechargeable)

Talk Time: Up to 9 hours *

Standby Time: Up to 250 hours *

* May vary depending on operation mode and mobile phone settings.

+ 8 hidden pages