CRC 125-14424 User Manual

SAFETY DATA SHEET
www.crcindustries.com
with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated
1. Identification
HydroForce® Stainless Steel Cleaner and PolishProduct identifier
Other means of identification
Product code
Recommended use
Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information Manufactured or sold by:
Company name
Address
Telephone
General Information
Technical Assistance
Customer Service
24-Hour Emergency
(CHEMTREC)
Website
14424 (Item #1004977)
Stainless steel cleaner
CRC Industries, Inc.
885 Louis Dr.
Warminster, PA 18974 US
215-674-4300
800-521-3168
800-272-4620
800-424-9300 (US)
703-527-3887 (International)
2. Hazard(s) identification
Physical hazards
Health hazards
Environmental hazards
OSHA defined hazards
Label elements
Signal word
Hazard statement
Precautionary statement
Prevention
Response
Liquefied gasGases under pressure
Category 2Skin corrosion/irritation
Category 2ASerious eye damage/eye irritation
Category 1Aspiration hazard
Category 3Hazardous to the aquatic environment, acute
hazard
Category 3Hazardous to the aquatic environment,
long-term hazard
Not classified.
Danger
Contains gas under pressure; may explode if heated. May be fatal if swallowed and enters airways. Causes skin irritation. Causes serious eye irritation. Harmful to aquatic life with long lasting effects.
Do not puncture or incinerate container. Do not expose to heat or store at temperatures above 49°C/120°F. Use with adequate ventilation. Open doors and windows or use other means to ensure a fresh air supply during use and while product is drying. If you experience any symptoms listed on this label, increase ventilation or leave the area. Wash thoroughly after handling. Wear eye protection/face protection. Wear protective gloves. Avoid release to the environment.
If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Wash
clothing and wash before reuse. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
SDS US
1 / 9
Storage
CAS number
%
Chemical name
Common name and synonyms
water
white mineral oil
Disposal
Hazard(s) not otherwise classified (HNOC)
Store locked up. Protect from sunlight. Store in a well-ventilated place. Exposure to high temperature may cause can to burst.
Dispose of contents/container in accordance with local/regional/national regulations.
3. Composition/information on ingredients
Mixtures
7732-18-5
8042-47-5
64742-47-8distillates (petroleum), hydrotreated
light
68476-86-8liquefied petroleum gas 5 - 10
577-11-7dioctyl sodium sulfosuccinate 1 - 3
Specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Inhalation
Skin contact
Eye contact
Ingestion
Most important symptoms/effects, acute and delayed
Indication of immediate medical attention and special treatment needed
General information
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a physician if symptoms develop or persist.
Remove contaminated clothing. Wash off immediately with soap and plenty of water. If skin irritation occurs: Get medical advice/attention. Wash contaminated clothing before reuse.
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.
Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs.
Aspiration may cause pulmonary edema and pneumonitis. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May cause redness and pain.
Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed.
Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves.
50 - 60
20 - 30
5 - 10
5. Fire-fighting measures
Suitable extinguishing media
Unsuitable extinguishing media
Specific hazards arising from the chemical
Special protective equipment and precautions for firefighters
Fire-fighting equipment/instructions
General fire hazards
Water fog. Foam. Dry chemical powder. Dry chemicals. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
Pressurized container may rupture when exposed to heat or flame. During fire, gases hazardous to health may be formed.
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without risk. Cool containers exposed to heat with water spray and remove container, if no risk is involved. Containers should be cooled with water to prevent vapor pressure build up.
Contents under pressure. Pressurized container may rupture when exposed to heat or flame.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Many gases are heavier than air and will spread along ground and collect in low or confined areas (sewers, basements, tanks). Many vapors are heavier than air and will spread along ground and collect in low or confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing during clean-up. Emergency personnel need self-contained breathing equipment. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
SDS US
2 / 9
Methods and materials for
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
with skin. Avoid prolonged exposure. Use only in well-ventilated areas. Wear appropriate personal
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
white mineral oil (CAS
US. ACGIH Threshold Limit Values
white mineral oil (CAS
US. NIOSH: Pocket Guide to Chemical Hazards
white mineral oil (CAS
containment and cleaning up
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. This product is miscible in water. Prevent product from entering drains. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS.
Environmental precautions
Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into drains, water courses or onto the ground.
7. Handling and storage
Precautions for safe handling
Conditions for safe storage, including any incompatibilities
Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke
expose containers to heat, flame, sparks, or other sources of ignition. Use caution around energized equipment. The metal container will conduct electricity if it contacts a live source. This may result in injury to the user from electrical shock and/or flash fire. Do not get this material in contact with eyes. Avoid contact with eyes, skin, and clothing. Avoid prolonged or repeated contact
protective equipment. Wash hands thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene practices. For product usage instructions, see the product label.
Level 1 Aerosol.
Contents under pressure. Do not expose to heat or store at temperatures above 120°F/49°C as can may burst. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. Store in a well-ventilated place. Store away from incompatible materials (see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit. At this time, the other constituents have no known exposure limits.
Type
PEL 400 mg/m3distillates (petroleum), hydrotreated light (CAS 64742-47-8)
PEL 5 mg/m3 Mist. 8042-47-5)
Type
TWA 5 mg/m3 Inhalable fraction. 8042-47-5)
Type
TWA 100 mg/m3distillates (petroleum), hydrotreated light (CAS 64742-47-8)
STEL 10 mg/m3 Mist. 8042-47-5)
TWA 5 mg/m3 Mist.
Biological limit values
Appropriate engineering controls
No biological exposure limits noted for the ingredient(s).
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Provide eyewash station. Eye wash fountain and emergency showers are recommended.
Individual protection measures, such as personal protective equipment
Eye/face protection
Wear safety glasses with side shields (or goggles).
ValueComponents
100 ppm
ValueComponents
ValueComponents
Form
Form
Form
Skin protection
Hand protection
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
Wear protective gloves such as: Nitrile. Polyvinyl chloride (PVC).
SDS US
3 / 9
Other
Inhalation
Skin contact
Respiratory protection
Thermal hazards
General hygiene considerations
Wear suitable protective clothing. Use of an impervious apron is recommended.
If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to determine actual employee exposure levels.
Wear appropriate thermal protective clothing, when necessary.
When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.
9. Physical and chemical properties
Appearance
Physical state
Form
Color
Odor
Odor threshold
pH
Melting point/freezing point
Initial boiling point and boiling range
Flash point
Evaporation rate
Flammability (solid, gas)
Upper/lower flammability or explosive limits
Flammability limit - lower (%)
Flammability limit - upper (%)
Vapor pressure
Vapor density
Relative density
Solubility (water)
Partition coefficient (n-octanol/water)
Auto-ignition temperature
Decomposition temperature
Viscosity (kinematic)
Percent volatile
Liquid.
Aerosol.
Milky white.
Mild petroleum.
Not available.
10.5
-56.2 °F (-49 °C) estimated
200 °F (93.3 °C) estimated
None (Tag Closed Cup)
Slow.
Not available.
0.6 % estimated
23.5 % estimated
321.7 hPa estimated
Not available.
0.92 estimated
Soluble.
Not available.
428 °F (220 °C) estimated
Not available.
Not available.
95 % estimated
10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous reactions
Conditions to avoid
Incompatible materials
Hazardous decomposition products
11. Toxicological information
Information on likely routes of exposure
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
The product is stable and non-reactive under normal conditions of use, storage and transport.
Material is stable under normal conditions.
No dangerous reaction known under conditions of normal use.
Heat, flames and sparks. Contact with incompatible materials.
Strong oxidizing agents.
Carbon oxides.
Prolonged inhalation may be harmful.
Causes skin irritation.
SDS US
4 / 9
Eye contact
Causes serious eye irritation.
Acute toxicity
white mineral oil (CAS 8042-47-5)
Respiratory sensitization
Carcinogenicity
white mineral oil (CAS 8042-47-5)
Chronic effects
Ingestion
Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia.
Symptoms related to the physical, chemical and toxicological characteristics
Aspiration may cause pulmonary edema and pneumonitis. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May cause redness and pain.
Information on toxicological effects
May be fatal if swallowed and enters airways.
distillates (petroleum), hydrotreated light (CAS 64742-47-8)
Acute
Dermal
LD50 Rabbit > 2000 mg/kg
Acute
Dermal
LD50 Rabbit > 2000 mg/kg
Inhalation
LC50 Rat > 5 mg/l, 4 hours
* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation
Serious eye damage/eye
Causes skin irritation.
Causes serious eye irritation.
irritation
Not a respiratory sensitizer.
Skin sensitization
Germ cell mutagenicity
This product is not expected to cause skin sensitization.
No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic.
Not classifiable as to carcinogenicity to humans.
IARC Monographs. Overall Evaluation of Carcinogenicity
3 Not classifiable as to carcinogenicity to humans.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not regulated.
US. National Toxicology Program (NTP) Report on Carcinogens
Not listed.
Reproductive toxicity
Specific target organ toxicity -
This product is not expected to cause reproductive or developmental effects.
Not classified.
single exposure
Specific target organ toxicity -
Not classified.
repeated exposure
Aspiration hazard
May be fatal if swallowed and enters airways. If aspirated into lungs during swallowing or vomiting, may cause chemical pneumonia, pulmonary injury or death.
Prolonged inhalation may be harmful. Prolonged exposure may cause chronic effects.
Test ResultsComponents Species
12. Ecological information
Ecotoxicity
Components Test ResultsSpecies
dioctyl sodium sulfosuccinate (CAS 577-11-7)
Aquatic
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
Harmful to aquatic life with long lasting effects.
LC50Fish 20 - 40 mg/l, 96 hoursRainbow trout,donaldson trout
(Oncorhynchus mykiss)
SDS US
5 / 9
Components Test ResultsSpecies
Partition coefficient n-octanol / water (log Kow)
waste disposal site. Contents under pressure. The dispensed liquid product is not a RCRA
distillates (petroleum), hydrotreated light (CAS 64742-47-8)
Aquatic
EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex)
* Estimates for product may be based on additional component data not shown.
Persistence and degradability
Bioaccumulative potential
No data is available on the degradability of this product.
distillates (petroleum), hydrotreated light > 4
Mobility in soil
Other adverse effects
No data available.
No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal of waste from residues / unused products
Hazardous waste code
Contaminated packaging
The dispensed liquid product is not a RCRA hazardous waste (See 40 CFR Part 261.20 - 261.33). Empty container can be recycled. Collect and reclaim or dispose in sealed containers at licensed
hazardous waste (See 40 CFR Part 261.20 - 261.33). Do not puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose in accordance with all applicable regulations.
Not regulated.
Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal.
14. Transport information
DOT
UN number UN proper shipping name Transport hazard class(es)
Class Subsidiary risk
Label(s) Packing group Special precautions for user Packaging exceptions Packaging non bulk Packaging bulk
IATA
UN number UN proper shipping name Transport hazard class(es)
Class
Subsidiary risk Packing group ERG Code Special precautions for user Other information
Passenger and cargo
aircraft
Cargo aircraft only
IMDG
UN number UN proper shipping name Transport hazard class(es)
Class
Subsidiary risk Packing group
UN1950 Aerosols, non-flammable, Limited Quantity
2.2
-
2.2 Not applicable. Read safety instructions, SDS and emergency procedures before handling. 306 None None
UN1950 Aerosols, non-flammable, Limited Quantity
2.2
­Not applicable. 2L Read safety instructions, SDS and emergency procedures before handling.
Allowed with restrictions.
Allowed with restrictions.
UN1950 AEROSOLS, Limited Quantity
2
­Not applicable.
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
SDS US
6 / 9
Environmental hazards
white mineral oil (CAS 8042-47-5)
white mineral oil (CAS 8042-47-5)
white mineral oil (CAS 8042-47-5)
Marine pollutant EmS Special precautions for user
No. F-D, S-U Read safety instructions, SDS and emergency procedures before handling.
15. Regulatory information
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not regulated.
US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance
Not listed.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
CERCLA Hazardous Substances: Reportable quantity
Not listed.
Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National
Response Center (800-424-8802) and to your Local Emergency Planning Committee.
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act (SDWA)
Food and Drug Administration (FDA)
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Section 311/312
Hazard categories
SARA 302 Extremely
hazardous substance
US state regulations
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd. (a))
liquefied petroleum gas (CAS 68476-86-8)
US. New Jersey Worker and Community Right-to-Know Act
Not listed.
US. Massachusetts RTK - Substance List
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
Not regulated.
Not regulated.
Immediate Hazard - Yes Delayed Hazard - No Fire Hazard - No Pressure Hazard - Yes Reactivity Hazard - No
No
US. Pennsylvania Worker and Community Right-to-Know Law
US. Rhode Island RTK
US. California Proposition 65
WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other
reproductive harm.
US - California Proposition 65 - CRT: Listed date/Carcinogenic substance
1,3-dichloropropene (CAS 542-75-6) Listed: January 1, 1989 1,4-dioxane (CAS 123-91-1) Listed: January 1, 1988
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
SDS US
7 / 9
diethanolamine (CAS 111-42-2) Listed: June 22, 2012
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
ethylene oxide (CAS 75-21-8) Listed: July 1, 1987 methylene chloride (CAS 75-09-2) Listed: April 1, 1988
US - California Proposition 65 - CRT: Listed date/Developmental toxin
ethylene oxide (CAS 75-21-8) Listed: August 7, 2009
US - California Proposition 65 - CRT: Listed date/Female reproductive toxin
ethylene oxide (CAS 75-21-8) Listed: February 27, 1987
US - California Proposition 65 - CRT: Listed date/Male reproductive toxin
ethylene oxide (CAS 75-21-8) Listed: August 7, 2009
Volatile organic compounds (VOC) regulations
EPA
VOC content (40 CFR
35.2 %
51.100(s))
Consumer products
Not regulated
(40 CFR 59, Subpt. C)
State
Consumer products
This product is regulated as a Metal Polish or Cleanser (aerosol). This product is compliant for use in all 50 states.
VOC content (CA)
VOC content (OTC)
14.5 %
14.5 %
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Substances (EINECS)
(PICCS)
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
NoAustralia Australian Inventory of Chemical Substances (AICS)
NoCanada Domestic Substances List (DSL)
YesCanada Non-Domestic Substances List (NDSL)
YesChina Inventory of Existing Chemical Substances in China (IECSC)
NoEurope European Inventory of Existing Commercial Chemical
NoEurope European List of Notified Chemical Substances (ELINCS)
NoJapan Inventory of Existing and New Chemical Substances (ENCS)
NoKorea Existing Chemicals List (ECL)
NoNew Zealand New Zealand Inventory
NoPhilippines Philippine Inventory of Chemicals and Chemical Substances
YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory
country(s).
16. Other information, including date of preparation or last revision
Issue date
Revision date
Prepared by
Version #
Further information
HMIS® ratings
NFPA ratings
NFPA ratings
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
04-30-2015
06-20-2017
Allison Yoon
03
CRC # 925B
Health: 2 Flammability: 1 Physical hazard: 0 Personal protection: B
Health: 2 Flammability: 1 Instability: 0
1
02
SDS US
8 / 9
Disclaimer
Revision Information
The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. This information is accurate to the best of CRC's knowledge or obtained from sources believed by CRC to be accurate. Before using any product, read all warnings and directions on the label. For further clarification of any information contained on this (M)SDS consult your supervisor, a health & safety professional, or CRC Industries, Inc..
Product and Company Identification: Product Codes First-aid measures: Eye contact First-aid measures: Most important symptoms/effects, acute and delayed Toxicological information: Corrosivity Toxicological information: Eye contact Toxicological information: Eye contact Toxicological information: Ingestion Toxicological information: Inhalation Toxicological information: Skin contact Toxicological information: Symptoms related to the physical, chemical and toxicological characteristics
Material name: HydroForce® Stainless Steel Cleaner and Polish
14424 (Item #1004977) Version #: 03 Revision date: 06-20-2017 Issue date: 04-30-2015
SDS US
9 / 9
Loading...