Page 1
SAFETY DATA SHEET
www.crcindustries.com
Extremely flammable aerosol. Contains gas under pressure; may explode if heated. May be fatal if
1. Identification
2-26® Multi-Purpose Precision LubricantProduct identifier
Other means of identification
Product code
Recommended use
Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information
Manufactured or sold by:
Company name
Address
Telephone
General Information
Technical
Assistance
Customer Service
24-Hour Emergency
(CHEMTREC)
Website
02005
Multi-purpose lubricant
None known.
CRC Industries, Inc.
885 Louis Dr.
Warminster, PA 18974 US
215-674-4300
800-521-3168
800-272-4620
800-424-9300 (US)
703-527-3887 (International)
2. Hazard(s) identification
Physical hazards
Health hazards
Environmental hazards
OSHA defined hazards
Label elements
Signal word
Hazard statement
Precautionary statement
Prevention
Response
Storage
Disposal
Hazard(s) not otherwise
classified (HNOC)
Category 1Flammable aerosols
Compressed gasGases under pressure
Category 1Aspiration hazard
Category 2Hazardous to the aquatic environment, acute
hazard
Not classified.
Danger
swallowed and enters airways. Toxic to aquatic life.
Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open
flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Do
not apply while equipment is energized. Extinguish all flames, pilot lights and heaters. Vapors will
accumulate readily and may ignite. Use only with adequate ventilation; maintain ventilation during
use and until all vapors are gone. Open doors and windows or use other means to ensure a fresh
air supply during use and while product is drying. If you experience any symptoms listed on this
label, increase ventilation or leave the area. Avoid release to the environment.
If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting.
Store in a well-ventilated place. Store locked up. Protect from sunlight. Do not expose to
temperatures exceeding 50°C/122°F. Exposure to high temperature may cause can to burst.
Dispose of contents/container in accordance with local/regional/national regulations.
None known.
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
SDS US
1 / 8
Page 2
3. Composition/information on ingredients
Mixtures
CAS number %Common name and synonymsChemical name
Distillates (petroleum), hydrotreated
light
Light mineral oil
n-Butyl stearate
Carbon dioxide
Petrolatum
Sorbitan monooleate
Specific chemical identity and/or percentage of composition has been withheld as a trade secret.
64742-47-8
8042-47-5
123-95-5
124-38-9
8009-03-8
68910-94-1
4. First-aid measures
Inhalation
Skin contact
Eye contact
Ingestion
Most important
symptoms/effects, acute and
delayed
Indication of immediate
medical attention and special
treatment needed
General information
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Rinse skin with water/shower. Take off contaminated clothing and wash before reuse. If skin
irritation occurs: Get medical advice/attention.
Rinse with water. Get medical attention if irritation develops and persists.
Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting.
Aspiration may cause pulmonary edema and pneumonitis. If vomiting occurs, keep head low so
that stomach content doesn't get into the lungs.
Aspiration may cause pulmonary edema and pneumonitis.
Provide general supportive measures and treat symptomatically. Keep victim under observation.
Symptoms may be delayed.
Ensure that medical personnel are aware of the material(s) involved, and take precautions to
protect themselves.
60 - 70
10 - 20
3 - 5
1 - 3
1 - 3
1 - 3
5. Fire-fighting measures
Suitable extinguishing media
Unsuitable extinguishing
media
Specific hazards arising from
the chemical
Special protective equipment
and precautions for firefighters
Fire-fighting
equipment/instructions
General fire hazards
Alcohol resistant foam. Dry chemical powder. Dry chemicals. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
Contents under pressure. Pressurized container may rupture when exposed to heat or flame.
During fire, gases hazardous to health may be formed.
Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without
risk. Cool containers exposed to heat with water spray and remove container, if no risk is involved.
Containers should be cooled with water to prevent vapor pressure build up.
Extremely flammable aerosol. Contents under pressure. Pressurized container may rupture when
exposed to heat or flame.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Methods and materials for
containment and cleaning up
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Many gases are heavier than air and will spread along ground and collect in low or
confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing
during clean-up. Emergency personnel need self-contained breathing equipment. Do not touch
damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate
closed spaces before entering them. Local authorities should be advised if significant spillages
cannot be contained. For personal protection, see section 8 of the SDS.
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep
combustibles (wood, paper, oil, etc.) away from spilled material. This product is miscible in water.
Prevent product from entering drains. Stop the flow of material, if this is without risk. Wipe up with
absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
For waste disposal, see section 13 of the SDS.
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
SDS US
2 / 8
Page 3
Environmental precautions
will conduct electricity if it contacts a live source. This may result in injury to the user from electrical
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
US. ACGIH Threshold Limit Values
US. NIOSH: Pocket Guide to Chemical Hazards
Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into
drains, water courses or onto the ground.
7. Handling and storage
Precautions for safe handling
Conditions for safe storage,
including any incompatibilities
Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Pressurized container: Do
not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray
on a naked flame or any other incandescent material. Do not smoke while using or until sprayed
surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame,
sparks, or other sources of ignition. Use caution around energized equipment. The metal container
shock and/or flash fire. Avoid prolonged or repeated contact with skin. Avoid prolonged exposure.
Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands
thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene
practices. For product usage instructions, please see the product label.
Level 3 Aerosol.
Pressurized container. Protect from sunlight and do not expose to temperatures exceeding
50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open flame,
heat or other sources of ignition. This material can accumulate static charge which may cause
spark and become an ignition source. Store in a well-ventilated place. Store away from
incompatible materials (see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
124-38-9)
8042-47-5)
8009-03-8)
124-38-9)
8042-47-5)
123-95-5)
8009-03-8)
124-38-9)
hydrotreated light (CAS
64742-47-8)
8042-47-5)
8009-03-8)
Biological limit values
Type
ValueComponents
PEL 9000 mg/m3Carbon dioxide (CAS
5000 ppm
PEL 5 mg/m3 Mist.Light mineral oil (CAS
PEL 5 mg/m3 Mist.Petrolatum (CAS
Type
ValueComponents
STEL 30000 ppmCarbon dioxide (CAS
TWA 5000 ppm
TWA 5 mg/m3 Inhalable fraction.Light mineral oil (CAS
TWA 10 mg/m3n-Butyl stearate (CAS
TWA 5 mg/m3 Inhalable fraction.Petrolatum (CAS
Type
ValueComponents
STEL 54000 mg/m3Carbon dioxide (CAS
30000 ppm
TWA 9000 mg/m3
5000 ppm
TWA 100 mg/m3Distillates (petroleum),
STEL 10 mg/m3 Mist.Light mineral oil (CAS
TWA 5 mg/m3 Mist.
STEL 10 mg/m3 Mist.Petrolatum (CAS
TWA 5 mg/m3 Mist.
No biological exposure limits noted for the ingredient(s).
Form
Form
Form
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
SDS US
3 / 8
Page 4
Appropriate engineering
controls
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level.
Individual protection measures, such as personal protective equipment
Eye/face protection
Wear safety glasses with side shields (or goggles).
Skin protection
Hand protection
Other
Respiratory protection
Wear protective gloves such as: Nitrile. Neoprene.
Wear suitable protective clothing.
If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a
NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained
breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to
determine actual employee exposure levels.
Thermal hazards
General hygiene
considerations
Wear appropriate thermal protective clothing, when necessary.
Always observe good personal hygiene measures, such as washing after handling the material
and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants.
9. Physical and chemical properties
Appearance
Physical state
Form
Color
Odor
Odor threshold
pH
Melting point/freezing point
Initial boiling point and boiling
range
Flash point
Evaporation rate
Flammability (solid, gas)
Upper/lower flammability or explosive limits
Flammability limit - lower
(%)
Flammability limit - upper
(%)
Vapor pressure
Vapor density
Relative density
Solubility (water)
Partition coefficient
(n-octanol/water)
Auto-ignition temperature
Decomposition temperature
Viscosity (kinematic)
Percent volatile
Liquid.
Aerosol.
Amber.
Mild petroleum.
Not available.
Not available.
-56.2 °F (-49 °C) estimated
Not available.
200 °F (93.3 °C) Tag Closed Cup
Slow.
Not available.
0.6 % estimated
5.5 % estimated
1557.7 hPa estimated
> 1 (air = 1)
0.84 estimated
Negligible.
Not available.
392 °F (200 °C) estimated
Not available.
Not available.
88.4 % estimated
10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
The product is stable and non-reactive under normal conditions of use, storage and transport.
Material is stable under normal conditions.
No dangerous reaction known under conditions of normal use.
SDS US
4 / 8
Page 5
Conditions to avoid
Inhalation
Skin contact
Eye contact
Acute toxicity
Respiratory sensitization
Carcinogenicity
Heat, flames and sparks. Avoid temperatures exceeding the flash point. Contact with incompatible
materials.
Incompatible materials
Hazardous decomposition
Strong oxidizing agents.
Carbon oxides.
products
11. Toxicological information
Information on likely routes of exposure
Prolonged inhalation may be harmful.
Prolonged skin contact may cause temporary irritation.
Direct contact with eyes may cause temporary irritation.
Ingestion
Symptoms related to the
physical, chemical and
toxicological characteristics
Information on toxicological effects
2-26® Multi-Purpose Precision Lubricant
Acute
Dermal
LD50 Rabbit 2475 mg/kg estimated
Inhalation
LC50 Rat 58740 ppm, 4 hours estimated
Oral
LD50 Rat 6263 mg/kg estimated
Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious
chemical pneumonia.
Aspiration may cause pulmonary edema and pneumonitis. Headache. Nausea, vomiting.
Diarrhea.
May be fatal if swallowed and enters airways.
Test ResultsProduct Species
* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation
Serious eye damage/eye
Prolonged skin contact may cause temporary irritation.
Direct contact with eyes may cause temporary irritation.
irritation
Not a respiratory sensitizer.
Skin sensitization
Germ cell mutagenicity
This product is not expected to cause skin sensitization.
No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
IARC Monographs. Overall Evaluation of Carcinogenicity
Light mineral oil (CAS 8042-47-5) 3 Not classifiable as to carcinogenicity to humans.
US. National Toxicology Program (NTP) Report on Carcinogens
Not available.
Reproductive toxicity
Specific target organ toxicity -
This product is not expected to cause reproductive or developmental effects.
Not classified.
single exposure
Specific target organ toxicity -
Not classified.
repeated exposure
Aspiration hazard
May be fatal if swallowed and enters airways. If aspirated into lungs during swallowing or vomiting,
may cause chemical pneumonia, pulmonary injury or death.
12. Ecological information
Ecotoxicity
Toxic to aquatic life.
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
SDS US
5 / 8
Page 6
Components Test ResultsSpecies
Acute
waste disposal site. Do not puncture, incinerate or crush. Contents under pressure. Do not allow
with chemical or used container. Dispose in accordance with all applicable regulations.
Distillates (petroleum), hydrotreated light (CAS 64742-47-8)
Aquatic
LC50Fish 2.2 mg/l, 96 hoursBluegill (Lepomis macrochirus)
* Estimates for product may be based on additional component data not shown.
Persistence and degradability
Bioaccumulative potential
Mobility in soil
Other adverse effects
No data is available on the degradability of this product.
No data available.
No data available.
No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal of waste from
residues / unused products
The dispensed liquid product is not a RCRA hazardous waste (See 40 CFR Part 261.20 - 261.33).
Empty container can be recycled. Collect and reclaim or dispose in sealed containers at licensed
this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches
Hazardous waste code
Contaminated packaging
Not regulated.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal.
14. Transport information
DOT
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Label(s)
Packing group
Special precautions for user
Special provisions
Packaging exceptions
Packaging non bulk
Packaging bulk
IATA
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Environmental hazards
ERG Code
Special precautions for user
Other information
Passenger and cargo
aircraft
Cargo aircraft only
IMDG
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Environmental hazards
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
UN1950
Aerosols, flammable, Limited Quantity
2.1
-
2.1
Not applicable.
Read safety instructions, SDS and emergency procedures before handling.
N82
306
None
None
UN1950
Aerosols, flammable, Limited Quantity
2.1
Not applicable.
No.
10L
Read safety instructions, SDS and emergency procedures before handling.
Allowed with restrictions.
Allowed with restrictions.
UN1950
AEROSOLS, LIMITED QUANTITY
2
Not applicable.
No.
SDS US
6 / 8
Page 7
EmS
Special precautions for user
F-D, S-U
Read safety instructions, SDS and emergency procedures before handling.
15. Regulatory information
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
SARA 304 Emergency release notification
Not regulated.
US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance
Not listed.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
CERCLA Hazardous Substances: Reportable quantity
Not listed.
Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National
Response Center (800-424-8802) and to your Local Emergency Planning Committee.
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act
(SDWA)
Food and Drug
Administration (FDA)
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Section 311/312
Hazard categories
SARA 302 Extremely
hazardous substance
US state regulations
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd.
(a))
Distillates (petroleum), hydrotreated light (CAS 64742-47-8)
Petrolatum (CAS 8009-03-8)
US. New Jersey Worker and Community Right-to-Know Act
Carbon dioxide (CAS 124-38-9)
US. Massachusetts RTK - Substance List
Carbon dioxide (CAS 124-38-9)
Light mineral oil (CAS 8042-47-5)
US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100)
Not listed.
US. Rhode Island RTK
None.
US. New Jersey Worker and Community Right-to-Know Act
Distillates (petroleum), hydrotreated light (CAS 64742-47-8)
US. Pennsylvania Worker and Community Right-to-Know Law
Carbon dioxide (CAS 124-38-9)
Distillates (petroleum), hydrotreated light (CAS 64742-47-8)
Light mineral oil (CAS 8042-47-5)
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
All components are on the U.S. EPA TSCA Inventory List.
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
Not regulated.
Not regulated.
Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - Yes
Pressure Hazard - Yes
Reactivity Hazard - No
No
SDS US
7 / 8
Page 8
US. California Proposition 65
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
Volatile organic compounds (VOC) regulations
EPA
VOC content (40 CFR
97.3 %
51.100(s))
Consumer products
Not regulated
(40 CFR 59, Subpt. C)
State
Consumer products
This product is regulated as a Multi-Purpose Lubricant. This product is compliant for use in all 50
states.
VOC content (CA)
VOC content (OTC)
0 %
0 %
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Substances (EINECS)
(PICCS)
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
YesAustralia Australian Inventory of Chemical Substances (AICS)
NoCanada Domestic Substances List (DSL)
YesCanada Non-Domestic Substances List (NDSL)
YesChina Inventory of Existing Chemical Substances in China (IECSC)
NoEurope European Inventory of Existing Commercial Chemical
NoEurope European List of Notified Chemical Substances (ELINCS)
NoJapan Inventory of Existing and New Chemical Substances (ENCS)
YesKorea Existing Chemicals List (ECL)
NoNew Zealand New Zealand Inventory
NoPhilippines Philippine Inventory of Chemicals and Chemical Substances
YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory
country(s).
16. Other information, including date of preparation or last revision
Issue date
Revision date
Prepared by
Version #
Further information
HMIS® ratings
NFPA ratings
NFPA ratings
Disclaimer
01-28-2016
01-28-2016
Allison Cho
03
CRC # 591B-C
Health: 1
Flammability: 3
Physical hazard: 0
Personal protection: B
Health: 1
Flammability: 3
Instability: 0
3
01
The information contained in this document applies to this specific material as supplied. It may not
be valid for this material if it is used in combination with any other materials. This information is
accurate to the best of CRC Industries' knowledge or obtained from sources believed by CRC to
be accurate. Before using any product, read all warnings and directions on the label. For further
clarification of any information contained on this (M)SDS consult your supervisor, a health & safety
professional, or CRC Industries.
Material name: 2-26® Multi-Purpose Precision Lubricant
02005 Version #: 03 Revision date: 01-28-2016 Issue date: 01-28-2016
SDS US
8 / 8
Loading...