Crazy Controllerz Xbox Instruction Manual

ππ]=="

Instruction Manual

Xbox One Modded Controller

Mode

Speed

Game: Gun

Mode 1:

20 SPS

Dual Rapid Fire

Mode 2:

20 SPS

Open Slot

Mode 3:

20 SPS

Open Slot

Mode 4:

20 SPS

Open Slot

Mode 5:

24 SPS

Call of Duty Ghosts (MP-443)

Mode 6:

22 SPS

Call of Duty Ghosts (P226)

Mode 7:

16 SPS

Call of Duty Ghosts (Rifles)

Mode 8:

20 SPS

Titanfall (Pistols)

Mode 9:

24 SPS

Titanfall (Rifles)

Mode 10:

20 SPS

Burst Fire (3-Shot Burst)

Rapid Fire Speed Guide

Syncing Your Controller

AutoSave

Your controller will automatically save every setting as you do it. You can remove the
battery pack at any time and your settings will always be saved.

Mode Memory

Warnings

•

Keep batteries fresh. #

•

Rechargeable battery packs are not recommended and may limit your
controllers performance. #

•

Console limitations may limit the max speed your controller can be adjusted to.#

•

Remember to always turn the Mod off after shutting down your controller.

Dual Rapid Fire

To use Dual Rapid Fire, scroll to mode 1 of your controller. Dual Rapid Fire will make
dual weapons both shoot with rapid fire when the left and right triggers are pulled.

Information

•

Instructions regarding Add-On Mods (if purchased) can be found on the
additional instruction sheet provided. #

•

SPS: Shots Per Second.#

•

Always pause your game before changing any settings.

Product Support Email!

[e-mail]

Your controller will remember the last mode you were in when you shut off your
controller. When you turn your controller on, it will automatically enter that mode.

Address:!

Crazy Controllerz#
2000 E Oakley Park Rd.#
Suite 206#
Commerce, MI 48382#
United States#

Department under Crazy Controllerz#
All contents subject to Copyright ©#

Contact!

[e-mail]#

Hours!

Monday-Friday#
8 AM-4:30 PM EST
www.CrazyControllerz.com

Reset a Mode to Default

To reset the mode you are in to it’s default settings, hold the right trigger and tap “up”
on the D-Pad. The guide button light will flash 2 times, pause, and then flash 2 more
times.

Adjusting Burst Fire Length (Complete All Steps)

You can adjust the number of shots in a burst (3 shot burst, 4 shot burst, etc.). To
adjust the burst length, first make sure you’re in burst mode (Mode 10). Then, hold
both the right trigger and left trigger and tap the Mod button. The guide button light
will flash 2 times. This signals you are in programming mode.

1. Hold the right trigger

2. Tap up on the D-Pad

1. Hold the left and right triggers

2. Tap the Mod button

Once you’re in programming mode, hold the right trigger and tap the Mod button to
increase the burst length by 1 shot. Hold the left trigger and tap the Mod button to
decrease the burst length by one shot. The controller is set to a 3-shot burst by
default.

1. Hold the left or right trigger

2. Tap the Mod button

Once your burst length is all set, you’ll need to save the settings. To save the
settings, hold both the right trigger and left trigger and tap the Mod button. The guide
button light will flash 3 times. This signals your settings have been saved.

1. Hold the left and right triggers

2. Tap the Mod button

Rapid Fire

To turn Rapid Fire on, tap the Mod button on the back of the controller. When Rapid
Fire is on, the guide button light will be on. When Rapid Fire is off, the guide button
light will be off.

1. Tap the Mod Button

2. Guide button light will turn On or Off

Adjusting Rapid Fire Speed

To increase the speed of any mode, hold the right trigger and tap “down” on the D­Pad. To decrease the speed of any mode, hold the left trigger and tap “down” on the
D-Pad. Each time you tap the D-Pad, the guide button light will flash.

1. Hold the left or right trigger

2. Tap down on the D-Pad

Changing Modes

You can change modes by going up a mode or by going down a mode. To go up one
mode, hold the Mod button and tap “up” on the D-Pad. To go down one mode, hold
the Mod button and tap “down” on the D-Pad. When you change modes, the guide
button light will flash which mode you are in. (ex. 3 flashes = Mode 3)

1. Hold the Mod Button

2. Tap up or down on the D-Pad

Reset to Factory Settings

To reset your controller back to it’s factory settings, hold the left trigger and tap “up”
on the D-Pad. The guide button light will flash 2 times, pause, and then flash 2
more times. This can be done in any mode.

1. Hold the left trigger

2. Tap up on the D-Pad