Crate & Barrel Ypsilon Sideboard Assembly Instruction

ASSEMBLY HARDWARE
Thank you for purchasing the Ypsilon Sideboard. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
12 - wood dowels
6 - small spring washers
door hinges
Missing hardware? Please call 800.606.6387 for replacements.
6 - small bolts
6 - small flat washers
2 - center door hinges
4 - large bolts
4 - large spring washers
36 - screws
6 - cam screws
4 - large flat washers
3 - pulls4 - side
6 - cams
8 - shelf pins
6 - pull bolts
TOOLS REQUIRED
phillips head screwdriver allen wrench (included)
(We recommend the use of hand tools instead of power tools)
1 - top panel
1 - bottom
1 - back panel
panel
1 - small adjustable shelf
Made in Vietnam - r06 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
1 - large adjustable shelf
2 - side panels
(1 left, 1 right)
3 - door fronts
(1 left, 1 center, 1 right)
4 - legs
(2 A, 2 B)
1 - partition
YPSILON SIDEBOARD
NOTE: Make sure arrows on each cam point towards nearest edge with holes
left side panel
right side panel
partition
1 Insert 2 wood dowels and 2 cams into left/right side panel and partition as shown. Make sure arrows on each cam point towards nearest edge with holes.
NOTE: Do not over tighten the cam screws
top panel
2 Place top panel upside down onto a clean, padded surface as shown. Insert 6 cam screws and 6 wood dowels into top panel. Secure, but do not over tighten, cam screws with a phillips head screwdriver.
right side panel
partition
top panel
left side panel
3 Fit dowels of top panel into corresponding holes of right/left side panels and partition as shown. Using a phillips head screwdriver, turn each cam clockwise until each cam securely engages each cam screw.
back panel
4 Fit back panel into corresponding grooves of left/right side panels and top panel as shown.
Made in Vietnam - r06 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
YPSILON SIDEBOARD
NOTE: Do not over
bottom panel
5 Fit dowels of bottom panel into corresponding holes of left/right side panel and partition. Secure bottom panel to left/right side panel and partition with 6 small bolts, 6
small spring washers and 6 small flat washers, using an allen wrench. Do not over tighten the bolts.
tighten the bolts
leg A
leg B
leg B
leg A
6 Attach 4 legs (2 A, 2 B) to bottom panel as shown. Secure each leg to bottom panel with 1 large bolt, 1 large spring washer, and 1 large flat washer as shown, using an allen wrench.
shelf
A
pins
small
B
adjustable shelf
large adjustable
B
shelf
A
7 A) With the assistance of anther adult, position unit upright as shown. Insert 8 shelf pins at desired shelf heights. Press shelf pins firmly to secure. B) Place 1 small adjustable shelf and 1 large adjustable shelf onto shelf pins as shown. Make sure shelves are securely supported by each shelf pin.
NOTE: Do not over tighten the screws
A
side
door hinge
left door front
pull
C
B
right door front
C
B
pull
8 A) Attach 2 side door hinges to left door front with 2 screws per hinge as shown. Secure, but do not over tighten, screws with a screwdriver. B) Attach 2 side door hinges to right door front with 2 screws per hinge as shown. C) Attach 1 pull to left and right door fronts with 2 pull
bolts as shown.
A
side door hinge
Made in Vietnam - r06 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
YPSILON SIDEBOARD
A
center door hinge
pull
B
9 A) Attach 2 center door hinges to center door with 2 screws per hinge as
shown. B) Attach 1 pull to center door front with 2 pull bolts as shown.
center door front
Refer to Hinge Adjustment diagram for adjusting the alignment of the door hinges.
left door front
right door front
center door front
10 Attach hinges of left, center and right door fronts to assembled unit. Secure each hinge with 4 screws, using a screwdriver as shown. Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
HINGE ADJUSTMENT
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated.
1
2
3
C
A
B
Side to side adjustment:
Loosen screw A, adjust gap with screw B and re-tighten screw A
A
B
Depth adjustment:
Loosen screw A, push hinge arm forwards or backwards, re-tighten screw A and secure screw B with a 1/4 turn clockwise
C
Height adjustment:
Loosen screw C, adjust door height and re-tighten screw C
Made in Vietnam - r06 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...