Page 1
WELLS 3-DRAWER DRESSER
HARDWARE
Thank you for purchasing the Wells 3-Drawer Dresser.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
12 - small
wood dowels
6 - pull
bolts
Missing hardware? Please call 800.606.6387 for replacements.
14 - large
wood dowels
20 - cam
screws
36 - small
screws
20 - cams
24 - large
screws
WALL MOUNTING HARDWARE
1 - wall
strap
1 - screw
1 - washer
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools.)
1- top panel
1 - top
crossbar
3 - drawer
crossbars
Made in Vietnam - r02 Page 1 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
2 - side panels
(1 right, 1 left)
2 - crossbars
(1 back, 1 front)
3 - drawer
bottoms
1 - small
drawer front
2 - drawer
fronts
1 - bottom
panel
2 - back panels
2 - small drawer sides
(1 right, 1 left)
4 - drawer sides
(2 right, 2 left)
3 - pulls
1 - small
drawer back
2 - drawer
backs
Page 2
WELLS 3-DRAWER DRESSER
left and right
side panel
1 Insert 9 cam screws into left and right side panels as
shown. Secure, but do not over tighten, cam screws using a
phillips head screwdriver.
NOTE: Make sure arrows
on each cam point toward
nearest edge with holes
A
top panel
bottom
panel
B
2 A) Insert 4 large wood dowels, 2 cam screws and 6
cams into top panel as shown. Make sure arrows on each
cam point toward nearest edge with holes.
B) Insert 4 large wood dowels and 6 cams into bottom
panel as shown.
A
back and front
crossbar
top
B
crossbar
3 A) Insert 2 large wood dowels and 2 cams into back
and front crossbars as shown.
B) Insert 2 large wood dowels and 4 cams into top
crossbar as shown.
top
crossbar
top panel
4 Fit cam screws of top panel into cams of top
crossbar as shown. Using a screwdriver, turn each cam
clockwise until it securely engages each cam screw.
Made in Vietnam - r02 Page 2 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3
WELLS 3-DRAWER DRESSER
top panel
assembly
front
crossbar
B
A
back
crossbar
bottom panel
left side
panel
C
5 A) Fit dowels of top panel and top crossbar into
corresponding holes of left side panel. Secure all cams.
B) Fit dowels of front and back crossbars into
corresponding holes of left side panel. Secure all cams.
C) Fit dowels of bottom panel into corresponding holes
of left side panel. Secure all cams.
top panel
assembly
A
front
crossbar
B
back
crossbar
C
bottom panel
right side
panel
6 A) Fit dowels of top panel and top crossbar into
corresponding holes of right side panel. Secure all cams.
B) Fit dowels of front and back crossbars into
corresponding holes of right side panel. Secure all cams.
C) Fit dowels of bottom panel into corresponding holes
of right side panel. Secure all cams.
NOTE: Do not over
tighten the screws
back panel
7 Attach 2 back panels to assembled unit with 36 small
screws as shown. Secure, but do not over tighten, the
screws using a phillips head screwdriver.
small drawer
right side
small drawer
front
A
C
B
8 A) Attach small drawer left and right sides with 2
large screws as shown, using a screwdriver.
B) Insert 4 small wood dowels into drawer crossbar as
shown.
C) Fit dowels of drawer crossbar into corresponding
holes of small drawer front as shown.
drawer
crossbar
NOTE: Make
sure wheels are
at the back
small drawer
left side
Made in Vietnam - r02 Page 3 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4
WELLS 3-DRAWER DRESSER
NOTE: Do not over
tighten the bolts
pull
B
small
drawer back
small
drawer bottom
9 Fit drawer bottom into grooves of small drawer sides
and small drawer front as shown.
A
10 A) Fit dowels of drawer crossbar into corresponding
holes of small drawer back. Attach small drawer back to
small drawer sides with 2 large screws as shown.
B) Attach 1 pull to small drawer front with 2 pull bolts as
shown. Secure, but do not over tighten, bolts with a
screwdriver.
Repeat steps 8-10 for remaining drawer assemblies.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the wood is finished with a protective clear lacquer.
11 Fit drawer glides of drawer assemblies into
corresponding drawer glides of assembled unit as shown.
Assembly is now complete.
Made in Vietnam - r02 Page 4 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 5
WELLS
3-DRAWER DRESSER
SAFETY MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is essential
to use wall anchors appropriate to your wall type (i.e. plaster,
drywall, concrete, etc.). Mount to wood studs whenever possible.
NOTE: Insert screws 3/4"-1"
from the edge of the strap
washer
screw
WALL
A. Insert screw (included) and washer through end wall strap and
into the top back of unit as shown.
B. Insert wall screw (not included) through end of wall strap and
into wall as shown.
Mounting assembly is now complete.
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your
local hardware store.
wall
strap
3/4”-1”
wall
screw
(NOTE: Additional
screw not included.
Please consult your
local hardware store.)
Made in Vietnam - r02 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 5 of 5
Page 6
WELLS MEDIA HUTCH
HARDWARE
Thank you for purchasing the Wells Media Hutch. This
page lists all the contents included in the box. Please
take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
1 - flat
washer
12 - cam
screws
Missing hardware?
Please call 800.606.6387 for replacements.
1 - spring
washer
1 - bolt
12 - cams
4 - screws 2 - connecting
10 - wood
dowels
plates
TOOLS REQUIRED
allen wrench (included)
(We recommend the use of hand tools instead of power tools)
phillips head screwdriver
(1 left, 1 right)
NOTE: Do not over
tighten the cam screws
left and right
A
side panels
NOTE: Make sure arrow on
each cam points toward
1 - back panel1 - top panel
nearest edge with holes
B
top panel
1 - partition2 - side panels
1 A) Insert 4 cam screws into left and right side panels
as shown. Secure, but do not over tighten cam screws with
a phillips head screwdriver.
B) Insert 4 cam screws, 4 wood dowels and 4 cams into
top panel as shown. Make sure arrow on each cam points
toward nearest edge with holes.
Made in Vietnam - r04 Page 1 of 2
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 7
WELLS MEDIA HUTCH
partition
A
back panel
B
2 A) Fit 2 wood dowels and 2 cams into partition as
shown.
B) Fit 4 wood dowels and 6 cams into back panel as
shown.
NOTE: Do not over
tighten the bolts
B
partition
C
A
back panel
3 A) Fit dowels of back panel into corresponding holes of
top panel. Using a screwdriver, turn each cam clockwise
until it securely engages each cam screw.
B) Fit dowels of partition into corresponding holes of top
panel as shown. Secure cams.
C) Secure partition to back panel with 1 bolt, 1 spring
washer and 1 flat washer as shown, using an allen
wrench. Do not over tighten the bolts.
top panel
right side
panel
left side
panel
4 Fit dowels of assembled unit into corresponding holes
of left and right side panel as shown. Secure all cams.
hutch
dresser
(sold separately)
connecting
plate
5 With the assistance of another adult, carefully place
hutch on top of dresser (sold separately) as shown.
Secure hutch to dresser with 2 connecting plates and 4
screws as shown, using a screwdriver.
Assembly is now complete.
CLEANING AND CARE
Made in Vietnam - r04 Page 2 of 2
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not
use furniture wax or polish as the wood is finished with a protective clear lacquer.
Loading...