Page 1
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
SLIDING DOOR CABINET
Thank you for purchasing the Springdale Sliding Door
Cabinet. This page
box. Please take the time to identify the hardware as
well as the individual components
you unpack and prepare for assembly, place the
contents on a carpeted or padded area to protect them
from damage.
Note: 2 people are required to safely assemble this product.
lists all the contents included in the
to this product. As
COMPONENTS
1 - top
panel
2 - adjustable
shelves
1 - support
panel
Made in China R05 Page 1 of 4
panels
HARDWARE
10 - wood
dowels
6 - small
screws
2 - metal
brackets
Missing hardware?
Please call 800.606.6387 for replacements.
14 - cams 14 - cam
screws
1 - pan
head screw
1 - wall
strap
1 - medium
screw
TOOLS REQUIRED
Phillips head screwdriver
1 - left side
panel
1 - right side
panel
1 - left door
panel
1 - fixed shelf 1 - crossbar1 - bottom panel2 - back
8 - shelf pin
1 - wall
anchor
1 - right door
panel
Page 2
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
SLIDING DOOR CABINET
A
B
A
Fixed
Shelf
Bottom
Panel
Crossbar
B
1
A) Insert 10 cams into 1 bottom panel, 1 fixed shelf,
and 1 crossbar. Make sure the arrows on each cam
point towards the nearest edge with holes.
B) Insert 4 wood dowels into bottom panel, and 2
wood dowels into crossbar as shown.
3
Fit bottom panel, fixed shelf, and crossbar onto
right side panel by aligning corresponding holes
with cam screws and wood dowels. Make sure
grooves on the bottom panel, fixed shelf, and
crossbar are towards the back.
Made in China R05 Page 2 of 4
2
Insert 10 cam screws into right side panel and left
side panel as illustrated above. Secure each cam
screw with a phillips head screwdriver.
B
A
A
Cam in
unlocked
position
4
A) Slide 2 back panels into grooves provided on
bottom panel, fixed shelf, and crossbar.
B) Secure right side panel by turning each cam
clockwise with a phillips head screwdriver.
Cam in
locked
position
B
Page 3
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
SLIDING DOOR CABINET
B
B
5
A) Fit left side panel onto assembled unit, by aligning
cam screws and wood dowels.
B) Secure unit by turning each cam clockwise with
phillips head screwdriver.
A
B
A) With the assistance of another adult, stand
7
assembled unit upright. Insert 4 cams into left and
right side panels.
B) Insert 4 cam screws into top panel and 4 wood
dowels into assembled unit as illustrated above.
Made in China R05 Page 3 of 4
A
6
Attach support panel to underside of bottom
panel with 2 wood dowels and 3 small screws as
illustrated above.
8
A) Fit top panel onto assembled unit, by aligning
cam screws and wood dowels.
B) Secure by turning each cam clockwise with a
phillips head screwdriver.
Page 4
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
SLIDING DOOR CABINET
A
B
10
A) Insert 8 shelf pins into side panels at desired level.
B) Place 2 adjustable shelves into unit, make sure
grooves are toward the back.
Made in China R05 Page 4 of 4
11
Fit the bottom rollers of the right door panel into
back groove and left door panel into the front groove
at the top and base of the cabinet assembly. Tilt the
doors up into position, depressing the levers at the
tops of the doors. Fit the door into the corresponding
grooves in the top panel and release the levers.
Assembly is now complete.
WALL MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the
wall mounting hardware by installed. For safe mounting, it
is essential to use appropriate fasteners for you wall type.
Mount to wood studs whenever possible.
A) Attach bracket to top center of cabinet with 1 medium
screw, using Phillips head screwdriver to tighten.
B) Mark location on wall approximately 2" below the
bracket mounted to the back of cabinet.
C) Drill a pilot hole into the wall stud. If no wall stud is
available, drill a hole into the wall that is slightly smaller in
diameter than the anchor. Gently tap anchor until flange is
flush with the wall.
D) Attach other bracket by inserting pan head screw
through bracket and into anchor on the wall.
E) Place unit so the bracket on the back edge is in line with
the bracket on the wall.
F) Lace one end of the wall strap through one bracket then
the other, bringing both ends together.
G) Ensure that the strap is secure.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer.
Loading...