Crate & Barrel Springdale Black Tall Cabinet, Springdale Tall Cabinet, Springdale Yellow Tall Cabinet Assembly Instruction
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE TALL CABINET
Thank you for purchasing the Springdale Tall Cabinet.
This page
Please take the time to identify the hardware as well as
the individual components
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
lists all the contents included in the box.
to this product. As you
COMPONENTS
1- left side
panel
1 - right
side panel
1 - door
panel
1 - crossbar
Made in China R04
HARDWARE
10 - wood
dowels
33 - wood
screws
1 - machine
screw
Missing hardware?
Please call 800.606.6387 for replacements.
14 - cams
8 - shelf pins
1 - medium
screw
14 - cam
screws
1 - knobs
1 - large
screw
TOOLS REQUIRED
Phillips head screwdriver
1 - top
panel
1 - fixed
shelf
2 - adjustable
shelves
1 - back
panel
1 - bottom
panel
2 - metal
brackets
1 - wall
strap
1 - wall
anchor
Page 1 of 4
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
Fixed
Shelf
Bottom
Panel
TALL CABINET
Crossbar
B
A
A
B
x6
x10
1
A) Insert 10 cams into 1 bottom panel, 1 fixed shelf,
and 1 crossbar as shown. Make sure the arrows on
each cam point towards the nearest edge with holes.
B) Insert 6 wood dowels into bottom panel, fixed
shelf, and crossbar.
B
x10
A
B
3
A) Fit bottom panel, fixed shelf, and crossbar to
right side panel by aligning corresponding holes with
cam screws and wood dowels. Attach left side
panel after right side panel is attached.
B) Secure assembly by turning all 10 cams clockwise
with a phillips head screwdriver.
Made in China R04
2
Insert 10 cam screws into right and left panel, as
illustrated above. Secure each screw with a phillips
head screwdriver.
B
x4
A
x4
4
With the assistance of another adult, carefully position
unit upright.
A) Insert 4 cams into left and right side panels.
B) Insert 4 cam screws and 4 wood dowels into top
panel.
Page 2 of 4
A
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
TALL CABINET
5
A) Fit top panel to assembled unit, by aligning cam
screws and wood dowels with corresponding holes.
B) Secure unit by turning each cam clockwise with
phillips head screwdriver.
B
A
A) Insert 8 shelf pins into side panels at desired
7
level.
B) Place 2 adjustable shelves into unit, make sure
grooves are towards the back.
Made in China R04
6
A) Attach back panel with 24 wood screws along
perimeter and center (use pilot holes as guides).
Secure with a phillips head screwdriver.
B
A
A) Attach 1 knob with 1 machine screw. Tighten with
8
the phillips head screwdriver.
B) Attach door panel with 3 wood screws per hinge,
as illustrated above.
B
x9
Page 3 of 4
Customer Service 800-967-6696 | http://www.crateandbarrel.com
SPRINGDALE
TALL CABINET
Place unit in its final location. If the floor is uneven or
9
the door doesn't appear square in the case frame,
adjust levellers on the underside of the legs up or
down to compensate.
Assembly is now complete.
Made in China R04
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the unit is finished with
a protective clear lacquer.
WALL MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use appropriate toggle or
molly bolts for your wall type. Mount to wood studs
whenever possible.
A) Attach bracket to top center of cabinet with wood
screw, using Phillips head screwdriver to tighten.
B) Mark location on wall approximately 2" below the
bracket mounted to the back of cabinet.
C) Drill a pilot hole into the wall stud. If no wall stud is
available, drill a hole into the wall that is slightly smaller
in diameter than the anchor. Gently tap anchor until
flange is flush with the wall.
D) Attach other bracket by inserting large screw
through bracket and into anchor on the wall.
E) Place unit so the bracket on the back edge is in line
with the bracket on the wall.
F) Lace one end of the wall strap through one bracket
then the other, bringing both ends together.
G) Ensure that the strap is secure.
Page 4 of 4
Loading...