Crate & Barrel Spa Bath Tower Assembly Instruction

SPA BATH CABINET
HARDWARE
Thank you for purchasing the Spa Bath Cabinet. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
4 - large bolts
4 - flat washers
8 - small bolts
4 - spring washers
12 - screws
4 - shelf pins
14 - wood dowels
2 - hinge bolts
21 - cam screws
2 - hinge plates
21 - cams
2 - door hinges
MOUNTING HARDWARE
2 - small screws
Missing hardware? Please call 800.606.6387 for replacements.
2 - large screws
2 - plastic anchors
1 - wall straps
2 - mounting brackets
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
2 - side panels
(1 left, 1 right)
1 - door top panel
1 - adjustable shelf
Made in Vietnam - r07 Page 1 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
panel
1 - door crossbar
2 - front crossbars
1 - door front
2 - back crossbars
2 - slat shelves
1 - top panel1 - back panel1 - door bottom
1 - top crossbar (front)
1 - top crossbar (rear)
SPA BATH CABINET
ASSEMBLY
right side panel
left side panel
1 With the assistance of another adult, place left and
right side panels onto a clean, padded surface. Insert 10 cam screws and 4 wood dowels into left and right side panels as shown. Secure cam screws with a phillips head screwdriver.
NOTE: Make sure arrow on cam points toward nearest edge with holes
door top panel
A
top panel
2 Insert 4 wood dowels into top panel as shown.
top crossbar
front crossbar
door bottom panel
B
back crossbar
3 A) Insert 5 cams into door top panel as shown. Make sure arrows on each cam points toward nearest edge with holes.
4 Insert 2 cams into each top crossbar, front crossbar and back crossbar as shown.
B) Insert 4 cams into door bottom panel.
Made in Vietnam - r07 Page 2 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
SPA BATH CABINET
front crossbars
top front crossbar
top rear crossbar
door top panel
B
A
door crossbar
5 A) Fit 2 wood dowels and 1 cam screw into door crossbar. B) Fit dowels of door crossbar into corresponding holes of door top panel. With a phillips head screw­driver, turn cam clockwise until it securely engages cam screw.
door top panel
door bottom panel
B
A
back
left side panel
6 A) Fit dowels of left side panel into corresponding holes of door bottom panel and door top panel as shown. Secure cams with a screwdriver. B) Fit dowels of top front/rear crossbars, back cross-
bars and front crossbars into corresponding holes of left side panel as shown. Secure all cams.
crossbars
back panel
7 Fit back panel into corresponding grooves of assembled unit as shown.
right side panel
8 With the assistance of another adult, fit dowels of right side panel into corresponding holes of assembled unit as shown. Secure all cams.
Made in Vietnam - r07 Page 3 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
SPA BATH CABINET
top panel
slat shelf
NOTE: Do not over tighten the bolts
9 Fit dowels of top panel into corresponding holes of assembled unit. Secure top panel with 4 large bolts, 4 spring washers and 4 flat washers using a screw­driver. Do not over tighten the bolts.
NOTE: Do not over tighten the screws
door hinge
10 Attach 2 slat shelves to assembled unit as shown. Secure each shelf with 4 small bolts using a screwdriver.
A
hinge plate
shelf pin
A
B
B
door front
12 A) With the assistance of another adult, carefully posi-
11 Attach 2 door hinges to door front with 2 screws per door hinge as shown. Secure, but do not over tighten, screws using a screwdriver.
Made in Vietnam - r05 Page 4 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
tion unit upright. Attach 2 hinge plates to assembled unit with 4 screws per plate as shown using a screwdriver. B) Insert 4 shelf pins into assembled unit at desired shelf height.
SPA BATH CABINET
hinge plate
door hinge
door assembly
adjustable shelf
13 Fit door hinges of door assembly into hinge plates of assembled unit as shown. Secure with 2 hinge bolts using a screwdriver.
14 Fit adjustable shelf onto shelf pins in assembled unit. Make sure shelf is securely supported onto each shelf pin. Assembly is now complete.
HINGE ADJUSTMENT
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated.
1) Side to side
adjustment:
Loosen screw A, adjust gap with screw B and re-tighten screw A.
2) Depth adjustment: Loosen screw A, push hinge armforwards or backwards, re-tighten screw A and secure screw B witha 1/4 turn clockwise.
3) Height adjustment: Loosen screw C, adjust door height and re­tighten screw C.
CLEANING & CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit is finished with a protective clear lacquer.
Made in Vietnam - r07 Page 5 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
SPA BATH CABINET
OPTIONAL WALL MOUNTING ASSEMBLY
wall bracket
plastic
C
anchor
wall strap
A
small screw
D
wall bracket
large screw
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. A) Attach 2 wall brackets to top panel using 2 small screws per bracket. B) Determine the final location of unit. Mark position on the wall, approximately 2" below the wall brackets mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) Attach 2 wall brackets to the wall by inserting 2 large screws through each wall bracket and into the wall anchor in the wall. E) Place the unit so the wall brackets on the back of the unit are aligned is allowed with the wall brackets. F) Lace one end of the wall strap through both brackets, and into the other end of the strap. G) Pull the strap tightly until secure. Repeat for remaining pair of wall brackets.
Wall mounting is now complete.
Made in Vietnam - r07 Page 6 of 6
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...