SENTRY WALL BOX
HARDWARE FOR WALL BOX WITH SHELF
Thank you for purchasing the Sentry Wall Box. This page
lists all the contents included in the box. Please take the
time to identify the hardware as well as the individual
components
to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or
padded area to protect them from damage.
WEIGHT LIMITATION
The Sentry Wall Box with Shelf is able to support up to
a total of 30 lbs and the Sentry Wall Box with Drawers
10 lbs per drawer.
anchor
wall
bracket
B
C
4 - screws
(for brick)
4 - anchors
(for brick)
4 - bolts
(for drywall)
4 - anchors
(for drywall)
2 - wall
brackets
4 - shelf
pins
HARDWARE FOR WALL BOX WITH DRAWERS
4 - screws
(for brick)
4 - anchors
(for brick)
4 - bolts
(for drywall)
Missing hardware?
Please call 800.606.6387 for replacements.
4 - anchors
(for drywall)
2 - wall
brackets
TOOLS REQUIRED
phillips head
screwdriver
drill
INSTALLATION INSTRUCTIONS
For safe mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, brick etc.). Mount to wood studs whenever
possible. The following instructions are for drywall
mounting only:
A. Determine final location of wall box. Position the
wall brackets 16” (41cm) apart as shown. Make sure
wall brackets are level and mark the 4 hole locations
A
onto the wall. Set wall brackets aside until further
instructions.
WALL
D
)
m
c
1
(4
”
6
1
B. Drill 4 pilot holes into marked positions on the wall
and into a wall stud. If the wall stud is not available, drill
a hole at each mark slightly smaller than the diameter of
the anchor.
C. Insert 4 anchors into holes. Make sure the flange of
each anchor is flush with the wall.
NOTE: If you are unsure about
your wall type or what mounting
method you should use, consult a
qualified professional or your local
hardware store.
Made in China - r05 Page 1 of 2
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
D. Attach wall brackets to the wall by inserting 2 bolts
through each bracket and each anchor in the wall.
SENTRY WALL BOX
ASSEMBLY INSTRUCTIONS FOR
WALL BOX WITH SHELF
WALL
wall
box
1 With the assistance of another adult, fit pre-
assembled brackets on back of unit into wall brack-
ets on wall as shown. Make sure unit is securely
supported by each bracket.
pre-assembled
wall bracket
wall bracket
B
2 A) Insert 4 shelf pins as shown.
B) Place shelf into wall box as shown. Make sure
shelf is securely supported by each shelf pin.
Assembly is now complete.
A
A
shelf
Made in China - r05 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
SENTRY WALL BOX
ASSEMBLY INSTRUCTIONS FOR
WALL BOX WITH DRAWERS
NOTE: The removal of the
drawers is not necessary to
properly install the wall box.
Doing this only allows you
to reduce the weight for
lifting during installation.
1 Extend drawer as far as possible. Using a phillips
head screwdriver, remove small screws from drawer
bottom as shown. Repeat for all remaining drawers.
Set drawers and screws aside.
WALL
2 With the assistance of another adult, fit pre-
assembled brackets on back of unit into wall brack-
ets on wall as shown. Make sure unit is securely
supported by each bracket.
pre-assembled
wall bracket
wall bracket
wall
box
Made in China - r05 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
SENTRY WALL BOX
drawer
drawer
glide
A. Extend drawer glides from
assembly as far out as possible.
Fit drawer onto glides as
shown.
B. Align holes of drawer glides
with drawer bottom and
secure with small screws,
using a phillips head screw-
driver. Do not over tighten the
screws.
C. Push drawer into assembled
unit. Repeat A-C for all remain-
ing drawers.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners.
Made in China - r05 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...