Crate & Barrel Ronan Four-Drawer Chest Assembly Instruction

RONAN 4 DRAWER CHEST
ASSEMBLY HARDWARE
Thank you for purchasing the Ronan 4 Drawer Chest. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
COMPONENTS
24- wood dowels
8 - cams
48 - small screws
Missing hardware? Please call 800.606.6387 for replacements.
32 - large screws
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead power tools)
8 - cam screws
1 - top panel
3 - front crossbars
8- drawer side panels
(4 left, 4 right)
Made in Indonesia - r11 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
1 - bottom panel
1 - back crossbar
4 - drawer bottoms
2 - side panels
(1 left, 1 right)
4 - drawer fronts
2 - back panels
4 - drawer backs
RONAN 4 DRAWER CHEST
NOTE: Make sure arrows on each cam point towards nearest edge with holes
bottom
B
panel
A
top panel
NOTE: Do not over tighten the cam screw
1 A) Place top panel onto a clean, padded surface. Insert 6 wood dowels and 4 cam screws into top panel as shown. Secure, but do not over tighten, cam screw with a
phillips head screwdriver.
B) Insert 4 cams and 2 wood dowels into bottom panel as shown. Make sure arrows on each cam point towards nearest edge with holes.
left and right
side panels
2 Insert 2 cams, 2 cam screws and 8 wood dowels into left and right side panels as shown.
right side panel
front crossbar
bottom
B
panel
A
left side panel
NOTE: Make sure crossbar of bottom panel faces back as shown
3 A) Fit wood dowels of left side panel into correspond­ing holes of 3 front crossbars as shown. B) Fit wood dowels of left side panel into corresponding holes of bottom panel as shown. Using a screwdriver, turn each cam clockwise until it securely engages each cam screw. Repeat steps 3A-3B for right side panel.
glides
4 With the assistance of another adult, place assembled unit upright. Carefully cut tape and remove from glides.
Made in Indonesia- r11 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
RONAN 4 DRAWER CHEST
top
B
panel
NOTE: Make sure crossbar of top panel faces front as shown
back
A
crossbar
5 A) Fit wood dowels of bottom panel into correspond­ing hole of back crossbar. B) Fit wood dowels of top panel into corresponding holes of left and right side panels. Secure all cams.
NOTE: Do not over tighten the screws
back panel
back panel
6 Attach 2 back panels to assembled unit with 12 small screws per back panel as shown, using a screw­driver. Do not over tighten the screws.
NOTE: Make sure drawer stops on the inside of drawer front are at the bottom
drawer right side panel
drawer front
drawer left side panel
7 Attach drawer left and right side panels to drawer front with 2 large screws per side as shown, using a
screwdriver.
drawer bottom
NOTE: Make sure glide locking devices on drawer bottom face drawer front as shown
8 Slide edge of drawer bottom with locking devices into grooves of assembled drawer first as shown.
Made in Indonesia - r11 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
RONAN 4 DRAWER CHEST
C
drawer
B
bottom
A
9 A) Attach drawer back to drawer left and right side panels with 2 large screws per side as shown.
Make sure notches face out and are at the bottom of the back panel as shown. B) Adjust drawer bottom to make sure space between inside of glide locking device and inside edge of side panel is even. C) Secure drawer bottom to drawer back and front with 6 small screws as shown. Repeat steps 6-8 for
remaining drawer assemblies.
drawer back
C
NOTE:Make sure notches face out and are at the bottom of the back panel as shown
drawer assembly
10 Fully extend top drawer glides of assembled unit. Carefully set 1 drawer assembly on top of extended drawer glides. Push drawer assembly into assembled unit until locking devices of drawer bottom engage drawer glides of assembly. Repeat
for remaining drawer assemblies.
Assembly is now complete.
drawer glide
locking device
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
Made in Indonesia - r11 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...