MOTEL DOUBLE GLIDER
Thank you for purchasing the Motel Double Glider.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
HARDWARE
10 - small
bolts
4 - end
caps
Missing hardware? Please call
800.606.6387 for replacements.
19 - large
bolts
4 - plastic
spacers
4 - acorn
nuts
58 - small
washers
TOOLS REQUIRED
hex wrench
(included)
(We recommend the use of hand tools instead of power tools)
allen wrench
(included)
29 - lock
nuts
16 - large
washers
COMPONENTS
2 - seats
2 - seat
backs
2 - inner leg frames
(1 left, 1 right)
1 - top
crossbar
1 - front
crossbar
1 - bottom
crossbar
2 - outer leg frames
(1 left, 1 right)
4 - swing
arms
1 - center
support
2 - side
supports
Made in China - r01 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
MOTEL DOUBLE GLIDER
NOTE: Do not over
tighten the bolts
seat
back
seat
1 Place seat and seat back onto a clean, padded
surface. Attach seat to seat back with 4 small bolts, 8
small washers and 4 lock nuts as shown. Make sure
bolts are attached from the backside of seat back.
Secure, but do not over tighten the bolts and nuts, using
an allen wrench and a hex wrench. Repeat for remain-
ing seat and seat back.
2 Attach 1 center support to 2 seat assemblies with 1
small bolt, 2 small washers and 1 lock nut as shown,
using an allen wrench.
seat
assembly
center
support
seat
assembly
top crossbar
inner left
leg frame
inner right
leg frame
3 Fit ends of inner left and right leg frames into top
crossbar as shown.
Made in China - r01
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
front crossbar
inner right
leg frame
inner left
leg frame
4 Position assembled inner leg frame as shown. With the
assistance of another adult, attach front crossbar to inner
left and right leg frames with 2 small bolts, 4 small
washers and 2 lock nuts as shown.
Page 2 of 4
MOTEL DOUBLE GLIDER
outer left
leg frame
bottom
crossbar
outer right
leg frame
5 Attach outer left and right leg frames to bottom
crossbar as shown. Loosely secure left and right
outer leg frames to bottom crossbar with 2 long
bolts, 4 washers and 2 lock nuts as shown. Do not
fully tighten bolts.
end cap
seat
assembly
B
B
inner leg
frame assembly
6 A) Loosely secure center support of seat assembly to
inner leg frame assembly with 1 bolt, 2 small washers and
1 lock nut. Do not fully tighten the bolts.
B) Fit 2 end caps into inner right and left leg frames as
shown.
A
inner leg
frame assembly
side support
seat
assembly
B
7 A) With the assistance of another adult, loosely attach
seat assembly to inner leg frame assembly with 1 large
bolt, 1 small washer, 1 plastic spacer, 1 side support, 1
small washer and 1 lock nut per side as shown. Do not
fully tighten bolts.
B) Loosely secure each side support to inner leg frame
assembly with 1 bolt, 2 small washers and 1 lock nut as
shown.
large
bolt
plastic
spacer
small
washer
A
small
washer
lock
nut
side support
Made in China - r01
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 4
MOTEL DOUBLE GLIDER
CORRECT
SIDE VIEW
side
support
lock
nut
acorn
nut
side support
NOTE: Do not
over tighten the
bolts
outer right
leg frame
small
washer
large
washer
A
INCORRECT
SIDE VIEW
side
support
large
washer
small
washer
A
outer right
leg frame
large
bolt
8 A) Loosely attach 4 swing arms to outer leg frame
assembly with 1 large bolt, 1 small washer, 2 large
washers, 1 small washer, 1 lock nut and 1 acorn
nut per arm as shown.
B) Loosely attach 4 swing arms to inner leg frame
assembly with 1 large bolt, 1 small washer, 2 large
washers, 2 small washers and 1 lock nut per arm as
shown. At this point, using an allen wrench and a hex
wrench, fully tighten all bolts and nuts. Do not over
tighten the bolts.
Assembly is now complete.
B
A
A
A
B
B
B
B
outer leg
frame assembly
swing arm
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners.
We recommend the use of outdoor furniture covers during inclement weather.
Periodically tighten bolts as necessary.
NOTE: Make sure acorn
nuts are assembled on the
outside of assembly as shown
Made in China - r01
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4 of 4
Loading...