Page 1
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
!
WARNING:
• Failure to follow these warnings and assembly instructions could result in serious injury or death.
• Read all instructions before assembling crib. Keep instructions for future use.
!
WARNING:
• For toddler bed use, the minimum age shall be no less than 15 months, and the maximum weight shall not be
greater than 50 lb (22.7 kg).
• Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an
infant.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
• Strings can cause strangulation! DO NOT place items with a string, cord or ribbon around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over crib or toddler bed, or attach strings to toys for any
reason.
• To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
• DO NOT place crib or toddler bed near windows where cords from blinds or drapes may strangle a child.
Fall Hazard:
• When child is able to pull to standing position, set mattress to lowest position and remove bumper pads, large toys
and other objects that could serve as steps for climbing out.
• When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be used and the
child should be placed in a youth or regular bed.
CAUTION: ANY MATTRESS USED IN THIS CRIB
!
MUST BE AT LEAST 27-1/4 INCHES (69 cm) BY 51-5/8
INCHES (131 cm) WITH A THICKNESS NOT EXCEEDING
6 INCHES (15 cm).
• Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly and
frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing,
damaged, or broken. Contact Crate and Barrel® for replacement parts and instructional literature if needed. DO NOT
substitute parts.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
• Infants can suffocate in gaps between crib sides and a mattress that is too small.
• Periodically check to see that all bolts are securely tightened.
• To clean crib: Wipe with clean soft cloth dampened with a mild cleanser and water. Rinse with clean water using a
soft cloth, and dry thoroughly.
• Follow warnings on all products in a crib.
• When a vaporizer is in use, always aim vapor steam away from the crib as well as away from other wood furniture.
Made in Vietnam - r09
800.967.6696 | crateandbarrel.com
Page 2
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
This page lists the contents included in the box. Please take
time to identify the hardware as well as the individual
components of the product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area
to protect them from damage. Please follow the assembly
instructions closely. Improper assembly can result in
personal or property damage.
Note: 2 adults are required to safely assemble this product.
WARNING:
CHOKING HAZARD - SMALL PARTS
Small parts present in unassembled state.
Adult assembly required.
CLEANINGANDCARE:
Cleansurfaceswithadryordampsoftcloth.Donotuseabrasivecleaners.
Periodically tighten bolts as necessary.
24 - Large bolts 4 - Support pins
4 - Bolt caps
24 - Flat washers
(pre-attached to large bolts)
24 - Spring washers
(pre-attached to large bolts)
Made in Vietnam - r09
1 - Small Allen wrench 1 - Large Allen wrench
Page 1 of 6
800.967.6696 | crateandbarrel.com
Page 3
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
2 - Side panels
1 - Bottom
dust panel
2 - End panels
1 - Mattress
support panel
Made in Vietnam - r09
A
2 - Leg A 2 - Leg B
800.967.6696 | crateandbarrel.com
B
Page 2 of 6
Page 4
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
A
A
A
B
B
1
Attach 1 leg A and 1 leg B to each side panel as shown. Secure, but not fully tighten, each leg with 2 large bolts, 2
spring washers and 2 flat washers, using a small Allen wrench.
(pre-attached to large bolts)
2
Made in Vietnam - r09
With assistance of another adult, attach 2 side panels to 1 end panel with 8 large bolts, 8 spring washers and 8 flat
washers as shown. Do not fully tighten until further instructions.
Page 3 of 6
800.967.6696 | crateandbarrel.com
Page 5
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
(pre-attached to large bolts)
3
With assistance of another adult, attach 2 side panels to remaining end panel with 8 large bolts, 8 spring washers
and 8 flat washers as shown. Do not fully tighten until further instructions.
Place bottom dust panel into assembly as shown. Make sure bottom dust panel is securely supported by legs and
4
Made in Vietnam - r09
assembly.
Page 4 of 6
800.967.6696 | crateandbarrel.com
Page 6
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
High
Middle
Low
5
Determine the desired height (low, middle, high) for the crib mattress. Fit each support pin into corresponding corner as
shown. Make sure support pin is securely engaged with assembly.
NOTE: Make sure
metal plate of mattress
panel is at the bottom
during assembly
Carefully place mattress support panel onto corresponding pins of assembly and secure with 4 bolt caps as shown.
6
Made in Vietnam - r09
Secure each cap with large Allen wrench. At this point, fully tighten all bolts. Assembly is now complete.
Page 5 of 6
800.967.6696 | crateandbarrel.com
Page 7
Mid-Century 3-in-1 Spindle Crib Assembly Instructions
Once the crib is in use, periodically check to make sure all bolts are tight, and tighten as necessary. Keep these
instructions for future use.
MAINTENANCE
Upon completion of assembly, be sure all screws, bolts and fastening devices have been tightened securely.
Periodically repeat this check to make sure all screws, bolts and fastening devices are tight. Before each usage or
assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts
are missing or broken. DO NOT substitute parts. DO NOT make any alteration to this crib.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth
lightly dampened in the solution. Rinse with clean water again using a soft clean cloth, then dry all surfaces
thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COARSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE
After completing the assembly process you are advised to read and beware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions. For long term storage of
the crib, store in a cool, dry place and keep away from moisture and extreme temperature changes.
Made in Vietnam - r09
Page 6 of 6
800.967.6696 | crateandbarrel.com
Loading...