MENDOCINO WORKBAR
Thank you for purchasing the Mendocino Workbar.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
HARDWARE
6 - washers 6 - nuts 6 - screws
Missing hardware? Please call
800.606.6387 for replacements.
4 - small
bolts
10 - large
bolts
WALL MOUNTING HARDWARE
1 - small
screw
1 - large
screw
1- wall
strap
1 - plastic
anchor
2 - wall
fittings
TOOLS REQUIRED
allen wrench key
(included)
(We recommend the use of hand tools instead of power tools)
hex wrench
(included)
phillips head screwdriver
(not included)
COMPONENTS
1 - back frame
2- legs
2 - small
shelves
3 - large
shelves
Made in Indonesia - r03 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
MENDOCINO WORKBAR
ASSEMBLY
C
threaded bolt
washer
nut
C
leg
screw
A
large shelf
large shelf
A
large shelf
large bolt
small shelf
small shelf
B
large bolt
B
small bolt
B
A
leg
B
back frame
A
1 A) With the assistance of another adult, place back frame onto a clean, padded surface. Loosely attach 3 large
shelves to back frame with 6 large bolts and 6 screws as shown. Do not tighten bolts or screws.
B) Loosely attach 2 small shelves to back frame with 4 large bolts and 4 small bolts as shown. Do not tighten the bolts
C) Fit threaded bolts of 2 legs into corresponding holes of 3 large shelves as shown. Secure each leg with 3 washers and
3 nuts. At this point, fully tighten all bolts using an allen wrench, all screws using a phillips head screwdriver and all
nuts using a hex wrench. Do not over tighten the bolts, screws or nuts. With the assistance of another adult, position
assembled unit upright.
Assembly is now complete.
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners.
CLEANING AND CARE
Periodically tighten bolts as necessary. We recommend the use of outdoor furniture
covers during inclement weather.
Made in Indonesia - r03
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 2 of 3
MENDONCINO WORKBAR
WALL MOUNTING ASSEMBLY
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall
type (i.e. plaster, drywall, concrete, etc.). Mount to wood
studs whenever possible.
A) Attach 1 wall fitting to assembled unit as shown, using
1 small screw.
B) Determine the final location of unit. Mark position on
the wall, approximately 2" below the bracket mounted to
the back of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach the wall fitting to the wall by inserting 1 large
screw through the wall fitting and into the plastic anchor
in the wall.
E) Place the unit so the wall fitting on the back edge is
aligned with the wall fitting on wall.
F) Lace one end of the wall strap through both fittings,
and into the other end of the strap.
G) Pull the strap tightly until secure.
F
wall strap
D
large screw
A
wall fitting &
small screw
C
plastic
anchor
Wall mounting assembly is now complete.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in Indonesia - r03 Page 3 of 3
Customer Service 800.967.6696 | Latest instructions avaliable at www.crateandbarrel.com
Loading...