Page 1
McALLISTER STEM HOLDER HUTCH
ASSEMBLY HARDWARE
Thank you for purchasing the McAllister Stem Holder
Hutch. This page lists all the contents included in the
box. Please take time to identify the hardware as well as
the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
4 - shelf pins
6 - plate
screws
3 - connecting
plates
WALL MOUNTING HARDWARE
4 - small
screws
Missing hardware? Please call 800.606.6387 for replacements.
4 - large
screws
2 - wall
straps
4 - wall
brackets
4 - plastic
anchors
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
NOTE: Make sure shelf
is securely supported
by shelf pins
A
A
B
adjustable shelf
1 - hutch assembly
1 A) Insert 4 shelf pins into holes at the desired shelf
height.
B) Place adjustable shelf into hutch assembly. Make
1 - adjustable shelf
Made in China - r01 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
sure shelf is securely supported by shelf pins.
Page 2
McALLISTER
UNIT CONFIGURATIONS
STEM HOLDER HUTCH
DB
door/drawer
base
SH DH
DBWB
WB
wine base
DB WB
MULTIPLE UNIT ASSEMBLY
SH
stem holder
hutch
SHDH
door hutch
bracket
DH
SH
WB
2 Any base and hutch can be configured to create
different buffet/hutch or wine tower combinations.
DH
DB
hutch
SH
DB
DH
WB
hutch
base
single hutch
A
and base assembly
3 A) For every hutch and base combination, it is
suggested that the 2 units be secured together with 2
connecting plates as shown. Secure each plate with 2
plate screws, using a phillips head screwdriver.
screw
bracket
screw
multiple hutch
B
base
and base assembly
B) For additional hutch and base assemblies, it is
suggested that every 2 assemblies are secure with 3
connecting plates as shown.
Made in China - r01 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3
McALLISTER
WALL MOUNTING ASSEMBLY
STEM HOLDER HUTCH
4 Safety Mounting Instructions
wall
bracket
large
D
screw
A
C
plastic
anchor
small
screw
F
wall
strap
wall
bracket
NOTE:
If you are unsure about your wall type or
what mounting method you should use,
consult a qualified professional or your
local hardware store.
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors appropriate
to your wall type (i.e. plaster, drywall, concrete, etc.).
Mount to wood studs whenever possible.
A) Attach wall bracket to top of unit using 2 small
screws as shown.
B) Determine the final location of unit. Mark position on
the wall, approximately 2" below the wall bracket
mounted to the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach wall bracket to the wall by inserting 2 large
screws, and into the plastic anchor in the wall.
E) Place the unit so the wall brackets on the back edge
are aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both
brackets, and into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets and
wall straps.
Wall mounting assembly is now complete.
CLEANING & CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit
is finished with a protective clear lacquer. It is recommended to use coasters to protect surface from heat and water.
Made in China - r01 Page 3 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...