MADISON SMALL BUFFET
HARDWARE
Thank you for purchasing the Madison Small Buffet. This
page
lists all the contents included in the box. Please
take the time
individual components
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
to identify the hardware as well as the
to this product. As you unpack
COMPONENTS
4 - glides
6 - case
hinges
4 - support
wedges
4 - adhesive
pads
6 - door
hinges
2 - plastic
brackets
TOOLS REQUIRED
Phillips head screwdriver
8 - shelf
pegs
screws
12 - cam
covers
20 - cam
screws
20 - cams22 - small
Missing hardware?
Please call 800.606.6387
for replacements.
hammer
8 - large
screws
34 - wood
dowels
1 - top panel
1 - bottom panel
2 - aprons
2 - side aprons
Made in Denmark - r07
3 - cabinet pulls
1 - large
back panel
2 - side
panels
1 - panel
connector
2 - small
back panels
1 - middle
partition
4 - legs3 - front
door panels
1 - large shelf
1 - small shelf
Page 1 of 5
MADISON SMALL BUFFET
B
A
C
1
A. Insert 1 cam screw per leg and tighten with a
phillips head screwdriver.
B. Insert 2 wood dowels into the ends of each long
apron.
C. Insert 2 cams into the face of each long apron.
Make sure the arrow on each cam points to the
closest short end of the the apron.
A
B
2
A. Fit 1 leg on the end of each long apron, aligning
dowels and cam screws with corresponding holes.
B. Secure legs by turning each cam 180º clockwise
with a phillips head screwdriver.
3
Repeat assembly method in Steps 1 and 2 for the
attachment of the 2 short aprons, using 4 wood
dowels, 2 cam screws, and 2 cams per apron.
Secure all cams with a phillips head screwdriver.
A
4
A) Align pre-drilled holes on apron with pre-drilled
holes on bottom panel. Insert 8 large screws
through front, back and side aprons into bottom
panel as shown. Secure each screw with a phillips
head screwdriver.
C) Using a hammer, gently tap in 1 glide onto the
bottom of each leg.
B
Made in Denmark - r07
Page 2 of 5
MADISON SMALL BUFFET
Top
Panel
5
A) Position assembled unit upright. Insert 6 cam screws
to the bottom panel as illustrated. Secure with a phillips
head screwdriver.
B) Attach 6 cam screws and 2 plastic brackets to the
underside of top panel. Set top panel aside.
A
Make sure
case hinges
face inwards
Side
Panel
Middle
Partition
Side
Panel
6
A) Insert 4 cams into 2 side panels and 1 middle
partition. Make sure arrows on each cam point
towards the short end of each panel.
B) Attach 2 case hinges to 2 side panels and 1 middle
partition with 2 small screws per hinge. Secure all screws
with a phillips head screwdriver.
A
B
B
B
7
A) Insert 6 wood dowels into 2 side panels and 1
middle partition. Press firmly to secure.
B) Fit 2 side panels and 1 middle partition onto cam
screws and bottom panel. Using a phillips head
screwdriver, turn bottom 6 cams 180º clockwise to
secure panels as illustrated above.
Made in Denmark - r07
A
A
8
A) Slide large and small back panels into grooves at
rear of side panels and middle partition.
B) Slide panel connector between 2 small back
panels.
Page 3 of 5
MADISON SMALL BUFFET
9
Carefully position top panel over assembled unit.
Align cam screws and wood dowels with
corresponding holes in the top and side panels.
Make sure the top panel brackets face the front of
the assembled unit.
10
Position 4 support wedges onto the back edges of
the assembled unit as shown. Secure each support
wedge with 1 small screw.
A
B
11
A) Attach 2 door hinges to 3 door panels with 2
small screws per hinge. Secure all screws with a
phillips head screwdriver.
B) Adhere 1 adhesive pad to top corner of each door
panel opposite of case hinge, as illustrated above.
B
A
12
A) Attach 3 front door panels to assembled unit. Fit
each door hinge into corresponding case hinge and
secure by tightening preinstalled screws in case hinge
with a screwdriver.
B) Insert 8 shelf pins to side panels and middle
partition at desired shelf height (adjustable).
Made in Denmark - r07
Page 4 of 5
MADISON SMALL BUFFET
13
Position 1 large shelf and 1 small shelf onto shelf
pegs in assembled unit.
14
Attach 3 door pulls to 3 door panels with 2 small
screws per door. Using a Phillips head screwdriver,
turn screws clockwise to secure.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
15
Attach 12 cam covers onto cams, as illustrated above.
Press firmly to secure. Assembly is now complete.
Made in Denmark - r07
Page 5 of 5
MADISON SMALL HUTCH
ASSEMBLY HARDWARE
Thank you for purchasing the Madison Small Hutch.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
28 - wood
dowels
6 - large
screws
3 - mending
plates
8 - cam
screws
2 - pulls
1 - felt
8 - cams
12 - shelf
pins
12 - connecting
bolts
4 - bumpers 4 - hinges
Missing hardware? Please call
800.606.6387 for replacements.
WALL MOUNTING HARDWARE
1 - cabinet
screw
2 - flat
washers
1 - wall
anchor strap
8 - cam
covers
12 - small
screws
4 - hinge
plates
1 - top
panel
1 - bottom
panel
1 - bottom
back panel
2 - partitions
1 - large adjustable
shelf
2 - side panels
(1 left, 1 right)
TOOLS REQUIRED
Made in Denmark - r06 Page 1 of 6
2 - small adjustable
shelves
phillips head screwdriver
Customer Service 800.967.6696 | www.crateandbarrel.com
2 - door fronts
1 - large back
panel
allen wrench
2 - small back
panels
MADISON SMALL HUTCH
A
B
left and right
side panels
1 A) Insert 4 cam screws and 3 wood dowels into left and
right side panels as shown. Secure cam screws with a
phillips head screwdriver.
B) Position each hinge plate over corresponding holes in side
panels. Secure hinges with pre-attached bolts, using a
screwdriver.
NOTE: Make sure
arrows on each cam
point towards nearest
edge with holes
A
bottom back
panel
B
bottom
panel
2 A) Insert 4 cams and 4 wood dowels into bottom back
panel as shown. Make sure arrows on each cam point towards
nearest edge with holes.
B) Insert 4 cams and 6 wood dowels into bottom panel as
shown.
right side
panel
bottom
panel
left side
panel
bottom
back panel
3 Fit dowels of bottom panel and bottom back
panel into corresponding holes of right and left side
panel as shown. With a screwdriver, turn cams
clockwise until it securely engages each cam screw.
partition
4 Insert 6 wood dowels into 2 partitions as shown.
Made in Denmark - r06 Page 2 of 6
Customer Service 800.967.6696 | www.crateandbarrel.com
MADISON SMALL HUTCH
B
partition
BACK VIEW OF
ASSEMBLED UNIT
A
felt
5 A) Adhere felt along bottom edge of assembled unit as
shown.
B) Fit dowels of partitions into corresponding holes of assembled
unit as shown.
small back
panel
large
back
panel
BACK VIEW OF
ASSEMBLED UNIT
small
back
panel
6 Secure bottom panel to assembled unit with 4
connecting bolts as shown, using an allen wrench.
top
panel
7 Slide 2 small back panels and 1 large back panel
through grooves of assembled unit as shown.
Made in Denmark - r06 Page 3 of 6
Customer Service 800.967.6696 | www.crateandbarrel.com
8 Fit dowels of assembled unit into corresponding
holes of top panel as shown.
MADISON SMALL HUTCH
9 Secure top panel to assembled unit with 8
connecting bolts as shown.
small
adjustable
shelf
large
adjustable
shelf
A
A
B
small
adjustable
shelf
10 A) Insert 12 shelf pins at desired shelf heights as shown.
B) Place 2 small adjustable shelves and 1 large adjustable
shelf into assembled unit. Make sure each shelf is securely
supported by shelf pins.
door
front
door
front
A
C
NOTE: Please refer
B
11 A) Attach 2 hinges to each door front with 2 small
screws per hinge as shown. Secure screws with a
screwdriver.
B) Attach 1 pull to each door front with 2 small screws as
shown. Secure screws with a screwdriver.
C) Adhere 2 bumpers to each door front as shown.
Made in Denmark - r06 Page 4 of 6
Customer Service 800.967.6696 | www.crateandbarrel.com
12 Attach hinges of 2 door fronts to hinge plates of
assembled unit as shown. Refer to diagram on page 5 for
hinge adjustment.
to diagram for
hinge adjustment.
MADISON SMALL HUTCH
13 With the assistance of another adult,
carefully place hutch on top of buffet as shown.
Attach 3 connecting brackets to back of
hutch/buffet assembly with 2 large screws per
bracket as shown. Secure screws with a
screwdriver.
Assembly is now complete.
BACK VIEW OF
ASSEMBLED UNITS
hutch
buffet
(sold separately)
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
HINGE ADJUSTMENT
If the doors do not appear square or aligned,
loosen or tighten the appropriate screws on
each case hinge as illustrated.
1) Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A.
A
B
2
3) Height adjustment:
Loosen screw C, adjust
door height and retighten screw C.
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw A and secure screw B with
a 1/4 turn clockwise.
A
B
1
C
C
3
Made in Denamrk - r06 Page 5 of 6
Customer Service 800.967.6696 | www.crateandbarrel.com
MADISON SMALL HUTCH
SIDE VIEW
flat
washer
cabinet
screw
NOTE: Insert screws 3/4"-1"
from the edge of the strap
wall
strap
wall screw
appropriate
to wall type
flat
washer
wall
wall anchor
appropriate
to wall type
WALL MOUNTING ASSEMBLY
For added safety and stability, it is recommended
that the wall mounting hardware be installed. For
safe mounting, it is essential to use wall anchors
made for your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
The included hardware is used for attaching wall
strap to unit only. You will need to purchase the
appropriate screw and anchor for your wall type.
NOTE: If you are unsure about your wall type or
what mounting method you should use, consult
a qualified professional or your local hardware
store.
Made in Denmark - r06 Page 6 of 6
Customer Service 800.967.6696 | www.crateandbarrel.com
A. Drill a hole in the wall slightly smaller
than the diameter of the wall anchor (not
included). Lightly tap with a hammer until
the face is flush with the wall.
B. Insert 1 wall screw (not included) and 1
flat washer through wall strap and into
the wall anchor.
C. Insert 1 cabinet screw and 1 flat
washer through wall anchor strap and into
the top of unit.
Loading...